• Journal of Ocean Engineering and Technology
• /
• v.20 no.1 s.68
• /
• pp.32-36
• /
• 2006

The initial hull form of a 100 tan, 45 knot class high-speed craft is newly developed. The resistance performances are investigated using a model test at high speed in a circulating water channel. The effect of the initial trim is studied together. Wave patterns are observed to clarify the relationship between the resistance performance and the wave characteristics. It can be found that the initial trim plays a role in increasing the resistance performance above a certain velocity.

• Journal of Korean Society of Water and Wastewater
• /
• v.22 no.3
• /
• pp.281-288
• /
• 2008

Cake resistance is influenced by floc size deposited on membrane surface. Enlarging floc size can reduce cake resistance. The small particles are enlarged by coagulation and flocculation process in conventional mixing tank at membrane filtration system. Fully-grown flocs for reducing the cake resistance, however, are ruptured while passing through a pump. In light of this fact, this study aims to experimentally look at the reaggregation phenomenon of mixing system. In addition, reaggregation phenomenon of mixing system is compared with first-aggregation of in-line injection system in which coagulant is injected just before a pump. These results suggest that first-aggregation of in-line injection system is better than reaggregation of mixing system for G-value above $3100sec^{-1}$. Since G-value in pipe of actual membrane filtration system are usually larger than $3100sec^{-1}$. The performance of in-line injection system is expected to be better than the conventional mixing tank system.

• Journal of the Korean Applied Science and Technology
• /
• v.24 no.4
• /
• pp.399-409
• /
• 2007

Characteristics of polyaniline anti-corrosive coatings with various primer coating resins(epoxy resin, urethane resin, and others) and top coating resins(epoxy and acrylic urethane resins) were investigated through adhesion, acid resistance, alkaline resistance, water resistance, and anti-corrosion tests. As a result, the anti-corrosive properties of the prepared coatings using polyaniline varied with the types of primer and top coating resins. In this condition, the properties of adhesion, chemical resistance, and water resistance were found to be very satisfactory when using emeraldine base (EB) of polyaniline blended with single-packaged urethane and acrylic urethane resins as the primer coatings, and using acrylic urethane resin as the top coatings. Also, the anti-corrosive function of these anti-corrosive coatings was well preserved for 1000 hr in the salt spray experiment.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.721-727
• /
• 2000

Impedance method was carried out to design the electrode that can measure the void fraction of the bubbly flow in pool reservoir. To find out the optimum electrode shape, Styrofoam-tests were performed in a specially designed acrylic reservoir. Three kinds of electrodes were designed to compare the characteristics of water-air flow. The resistance was increased as the void fraction increased and the capacitance was decreased as the void fraction increased. The resistance is a main parameter to express the nature of the water-air flow in impedance method. Almost all the values of impedance were involved in resistance. The degree of deviation from the mean-resistance values showed reasonable results. Electrode type-I expressed excellent results among the three electrode shapes. The impedance values in void fraction 0-10% were similar to those of Maxwell's equation. But the impedance values in void fraction 10-20% were not similar to those of Maxwell' equation because of the edge effect near electrode.

• Korean Journal Plant Pathology
• /
• v.14 no.6
• /
• pp.594-597
• /
• 1998

The optimal quantity of inoculum was determined to screen resistance of garlic cultivars against Sclerotium cepivorum and 30 cultivars was tested. The growth of the pathogen in detached roots, Disease incidence was increased when the inoculum density was raised form 10 to 100 sclerotia. The optimal inoculum density to differentiate resistance or susceptibility of garlic cultivars was seemed to be 50 sclerotia. The cultivars collected from England, Japan, Nepal and Turkey, and cultivars such as common red, PI1356104 and PI135693 were less than the other cultivars in their disease incidence. The growth of S. cepivorum in detached roots varied from 23 to 33 mm according to garlic cultivars. There was no relationship between the disease incidence and the growth in detached roots. The sclerotial germination was increased significantly when root extract was extract was added. The addition of only distilled water resulted in 13% germination, but the addition of 0.25 g of root extract in 100 ml distilled water resulted in more than 85% germination. There was no difference in the stimulation of sclerotial germination among cultivars which showed different resistance.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10b
• /
• pp.1267-1272
• /
• 2000

When fresh concrete is exposed to low temperature, the concrete may suffer frost damage due to freezing at early ages and strength development may be delayed. These are problems on cold weather concrete. One of the solution methods for resolving these problems has been to reduce the freezing temperature of concrete by the use of chemical admixtures called Accelerators for freezing resistance. Therefore, in this study, we executed freezing temperature of mortar, setting and strength properties with using water reducing accelerator and accelerators for freezing resistance which are producted internationally. As a result of this experiment, the freezing temperature of mortar is lower and the setting property is promoted when the admixing content of accelerators for freezing resistance is increased. Moreover, the compressive strength of mortar used accelerators for freezing resistance represented the result which is similar with result of analysis of compressive strength increase with using logistic curve formula, but in the case of plain and using water reducing accelerator, there is no relation between logistic curve formula, maturity and compressive strength.

• Journal of Ocean Engineering and Technology
• /
• v.26 no.6
• /
• pp.14-18
• /
• 2012

A 30ft class aluminum leisure boat is newly developed and the resistance performances are investigated by a model test at a high-speed circulating water channel. The effect of a fin attached to the side of the hull is studied at two different displacements. Wave patterns are observed to make clear the relationship between the resistance performance and wave characteristics. It can be found that a chine position at the draft line can have a strong effect on the resistance performance around a certain velocity range.

• Ocean Systems Engineering
• /
• v.7 no.4
• /
• pp.371-398
• /
• 2017

Calm water wave resistance plays a very important role in ship hull design. Numerical methods are meaningful for this reason. In this study, two prevailing methods, the Neumann-Kelvin and the Rankine source method, were implemented and compared. The Neumann-Kelvin method assumes linearized free surface boundary condition and only needs to mesh the hull surface. The Rankine source method considers nonlinear free surface boundary condition and meshes both the ship hull surface and free surface. Both methods were implemented and the wave resistance of a Wigley III and three Series 60(Cb=0.6, 0.7, 0.8) hulls were analyzed. The results were compared with experimental results and the merits of both numerical techniques were quantified. Based on the results, it is concluded that the Rankine source method is more accurate in the calculation of the wave-making resistance. Using the Neumann-Kelvin method, it is found to be easier to model the hull and can be used for slender ships to solve problems like wave current coupling calculation.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.06a
• /
• pp.12-13
• /
• 2020

Construction projects and buildings are becoming taller and larger, and the size of water tanks of production facilities and high-rise buildings is also gradually increasing. Most large water tanks apply a waterproofing layer to the water tank type concrete structure. The application of polyurea coating materials, which are excellent in water resistance, chemical resistance, physical performance, rapid hardening, and workability is gradually increasing as waterproofing and anticorrosion layer for water tank. As a result, defects such as water leakage and damage to the waterproofing layer are continuously occurring, causing production disruption, setback to users. Therefore, it is required to review suitability through performance verification of the waterproofing and anticorrosion system.

• Journal of Korean Society for Quality Management
• /
• v.46 no.3
• /
• pp.425-440
• /
• 2018

Purpose: This study is aimed at developing of the flex resistance testing process at low temperature with the waterproof fabric to suit the military environment, and is designed to fit for the purpose of the waterproof materials in order to optimize the test method by finding out matters to improve from existing the test method and through previous studies. Methods: The test method, which has been applied to flex resistance of existing water-repellent materials, was improved and consequently, differentiated test results could be obtained according to the test temperature, sample size, and flexing method. Results: The testing of the total of 8 samples revealed that performance of the military requirement could hardly be met just by presenting the materials or 2~3 layers when the quality criteria for high functional water repellent fabrics were applied. PTFE(Polytetrafluoroethylene) is preferred to PU(Polyurethane) to be used in the extremely low-temperature environment, but durability under the low-temperature environment may be varied depending on film thickness or laminating technique even if the materials of waterproof films are identical. Therefore, in addition to the material or texture, the test method capable of reflecting durability under the low-temperature environment shall be suggested, and the newly designed test method proposed in this study was shown to suggest differentiated quality criteria by the material. Conclusion: The water resistance measurement and the test method following flex resistance with expanded range of flex will enable the differentiable test of the samples according to the number of repetition. This study is meaningful in that it suggests a differentiable test method capable of establishing a basis of deciding suitable material when selecting military goods made of water repellent material by properly improving the test method.