• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.6
• /
• pp.779-787
• /
• 2002

The cooling heat transfer by impinging water spray jets on a rotating roll with a relatively large diameter has been investigated under various experimental conditions with 3 different sizes of flat type nozzle. The local heat transfer coefficients were calculated by finite difference method using measured surface temperatures of the circular cylinder as boundary conditions. Results show that a peak value of the heat transfer coefficient is located at the center of sprayed area and there may be a secondary peak at the downstream. The average heat transfer coefficients on the sprayed area were found to be 10 to 22 ㎾/$m^2$$^{\circ}C$, and were not related to spraying pressure, but approximately linearly to flow rate of sprayed water. Also it is found that increasing the distance from roll to nozzle could improve the cooling efficiency by increasing the sprayed area.

• Journal of Korea Water Resources Association
• /
• v.30 no.6
• /
• pp.743-751
• /
• 1997

A thorough literatural review of researches on the experimental prediction of scour depths caused by jets was carried out to find out a measure of scour prediction. A new experimental equation for predicting scour depths due to a vortical or an inclined jet was developed from five hundreds of experimental data which were carefully reviewed and adopted from the previous researches. The developed equation shows 0.941 statistical correlation coefficient. It was found that the parameters governing the scour depth were the size of bed material, flow rate through unit width of spillway, and head drop across structure. The predicted scour depth could be expressed as the deepest scouring depth below tail water surface with correlation coefficient ${\gamma}$ = 0.941.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.14 no.6
• /
• pp.441-449
• /
• 2002

Single-phase convection and partial nucleate boiling in free-surface and submerged jet impingements of subcooled water ejected through a 2-mm-diameter circular pipe nozzle were investigated by local measurements. Effects of jet velocity and nozzle-to-imping-ing surface distance as well as heat flux on distributions of wall temperature and heat transfer coefficients were considered. Incipience of boiling began from far downstream in contrast with the cases of the planar water jets of high Reynolds numbers. Heat flux increase and velocity decrease reduced the temperature difference between stagnation and far downstream regions with the increasing influence of boiling in partial boiling regime. The chance in nozzle-to-impinging surface distance from H/d=1 to 12 had a significant effect on heat transfer around the stagnation point of the submerged jet, but not for the free-surface jet. The submerged jet provided the lower cooling performance than the free-surface jet due to the entrainment of the pool fluid of which temperature increased.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.6
• /
• pp.1385-1394
• /
• 1994

A three-dimensional numerical model of surface buoyant jets with variable density was established. The model uses fully nonlinear, time-dependent, three-dimensional, ${\sigma}$-transformed equations of motion and equation of heat transport. A semi-implicit numerical scheme in time has been adopted for computational efficiency. The model was applied for thermal jets discharging into a stagnant water and the simulated results were compared with a hydraulic experimental data set showing good agreement. Comparative studies of exchange coefficients and stability functions indicated that spatial variation of exchange coefficients should be considered and the existing stability functions should be modified to simulate surface buoyant jets accurately.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.11-14
• /
• 2009

The implementation of gelled propellants systems offers high performance, thrust-control, energy management of propulsion, storability, and high density impulse of solid propulsion. Present study focused on the spray behavior of liquid sheets formed by impinging jets of non-Newtonian liquids which are mixed by Carbopol 941 0.5%wt. The results are then compared with experiments conducted on spray images formed by impinging jets concerning with air-blast effect at center orifice. When gel propellants are injected by doublet impinging jets at low pressure, closed rim pattern shape appeared. As increasing air mass flow rate(decreasing GLR), spray breakup and atomization phenomenon better improved and spray structure instabilities for the effect of air-blast are also increased.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2001.10a
• /
• pp.121-121
• /
• 2001

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.12
• /
• pp.1051-1056
• /
• 2014

After hot rolling, a high-temperature steel plate with a temperature higher than $800^{\circ}C$ is rapidly cooled by multiple circular water jets. In this cooling process, because the temperature of the steel plate is much higher than the boiling point of the cooling water, film-boiling heat transfer occurs and a very thin steam layer forms between the plate surface and the cooling water. The steam layer acts as a thermal resistance that prevents heat transfer between the cooling water and the steel plate. In addition to the film-boiling heat transfer, complex physical phenomena such as the free-surface flow of residual water that accumulated on the material and the material's high-speed motion also occur in the cooling process. In this study, the simultaneous cooling process of the upper and lower sides of a running hot steel strip is investigated using a three-dimensional numerical model and the cooling performances and characteristics of the upper-side cooling and lower-side cooling are compared.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.233-236
• /
• 2002

The high-pressurized spray nozzle is used f3r special washing and cutting with strong impact force. The performance of this nozzle, which focused on spray penetration and radial dispersion, was mainly investigated to maximize the momentum and minimize the flow loss. Hence, our experimental research was conducted by changing the aspect ratio ranging from 0 to 3 with nozzle outlet of 1.1. The spray trajectory far high-pressurized water was experimentally investigated using PDPA diagnostics, which was available at spray downstream region. As the spray at upstream near the nozzle exit did not show the improved disintegration. The results showed empirical correlation with regard to non-dimensional axial velocity distribution, spray penetration, and radial spreading rate with photographic visualization.

• Journal of ILASS-Korea
• /
• v.9 no.4
• /
• pp.1-8
• /
• 2004

Breakup characteristics of liquid sheets formed by the impingement of two water jets, such as a breakup length and a breakup wavelength of sheet, were investigated as increasing the injection velocity up to 30m/s and the ambient gas pressure up to 4.0MPa. While round edged orifices formed a laminar sheet which has no waves on the sheet when the injection velocity is low, sharp edged orifices formed a turbulent sheet which has impact waves irrespective of the injection velocity. Thus we compared the differences of breakup characteristics between them. The results showed that the aerodynamic force significantly affects the breakup of laminar sheet when the gas based Weber number is higher than unity, It was also found that the turbulent sheets have three breakup regimes, i.e. expansion regime, wave breakup regime and catastrophic breakup regime according to the gas based Weber number.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.173-179
• /
• 2004

Breakup characteristics of liquid sheets formed by the impingement of two water jets, such as a breakup length and a breakup wavelength of sheet, were investigated as increasing the injection velocity up to 30m/s and the ambient gas pressure up to 4.0㎫. While round edged orifices formed a laminar sheet which has no waves on the sheet when the injection velocity is low, sharp edged orifices formed a turbulent sheet which has impact waves irrespective of the injection velocity. Thus we compared the differences of breakup characteristics between them. The results showed that the aerodynamic force significantly affects the breakup of laminar sheet when the gas based Weber number is higher than unity. It was also found that the turbulent sheets have three breakup regimes, i.e. expansion regime, wave breakup regime and catastrophic breakup regime according to the gas based Weber number.