• Korean Journal of Agricultural and Forest Meteorology
• /
• v.7 no.1
• /
• pp.107-114
• /
• 2005

Soil CO₂ emission is one of the primary components in carbon balance of terrestrial ecosystems. In soil CO₂ flux measurements, chamber method is currently the most common technique. Prior to compare or synthesize the data collected from different chamber methods, potential biases must be quantified for each measurement system. We have conducted an intercomparison experiment among four closed dynamic chamber systems and an automatic open-closed chamber system in a temperature-controlled phytotron. Due to the disturbed CO₂ concentrations inside the phytotron during the measurements with closed dynamic chambers and the changes in soil water content, the interpretation of the data was difficult to quantify the biases of individual methods. However, the experiment provided not only valuable information on the performance characteristics of the five instruments to varying soil temperature and CO₂ concentration but also useful insights for better designs and strategy for future intercomparison in a controlled environment.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.2
• /
• pp.178-182
• /
• 2006

The purpose of this research is to remove the bromate that is a disinfection by-poduct of water purification by ozone. I achieved a high rate of removal with iron, copper, or silver impregnated activated carbon by using both the adsorbing power of granular activated carbon and the oxidizing power of metal ions as deoxidizing agents. In the removal test of bromate with the quantity of activated carbon input I injected each activated carbon by 0.1, 0.3, 0.1, and 1.0 g and let them react for 240 minutes. I found the quantity of removed bromate was in proportion to the amount of input. The removal rate of bromate increased about 20% when I used acid treated activated carbon. The metal impregnated activated carbon had a higher removal rate of bromate than that of general activated carbon by about $30{\sim}50%$. Iron impregnated activated carbon showed a 92% removal rate of bromate. Iron, copper, or silver impregnated activated carbon removed about $0.9{\sim}1.5mg\;{BrO_3}^-/g$ while general activated carbon removed about $0.02{\sim}0.45mg\;{BrO_3}^-/g$. In the continuous column reaction, there were breakthrough phenomena at 96, 180, and 252 hours when I tested EBCT by 1, 2 and 3 minutes while I was changing the flux rate of bromate from 15.6 to 46.8 mL/min.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.5
• /
• pp.117-124
• /
• 2010

Most of the rivers which exist in nature are not a single river but the network that is composed of several branches and mainstreams. The river network are more complicated than other sigle rivers and streams. Therefore the hydraulic characteristics are sensitively changed by reduction and expansion of the width in the confluence or the variation of the flux. In this paper, the hydraulic characteristics were calculated by the change of the width and length in the confluence and the hydraulic model test. The deposit of confluence emerged at the left bank, right bank and the stagnation sector. As the total flow in the branch have increased, stagnation of the left bank and right bank have decreased. When the width of the downstream have been get smaller from 3 m to 2 m, the deposit of the left bank and right bank and stagnation sector have decreased. But as the eddy flow in the center of the confluence is occurred, the erosion has been increased. The result of this paper can be used as a basic data of water management around the junction and for maintenance on the ground of development of the river.

• Korean Journal of Medicinal Crop Science
• /
• v.28 no.1
• /
• pp.1-8
• /
• 2020

Background: This study was conducted to investigate the effects of NaCl concentration on the photosynthetic parameters, chlorophyll fluorescence and growth characteristics of Crepidiastrum sonchifolium. Methods and Results: As treatments, we subjected C. sonchifolium plants to four different concentrations of NaCl (0, 50, 100 and 200 mM). We found that the photosynthetic parameters maximum photosynthesis rate (P_{N max}), net apparent quantum yield (Φ), maximum carboxylation rate (V_cmax), and maximum electron transport rate (J_max) were significantly reduced at an NaCl concentration greater than 100 mM. In contrast, there was an increase in water-use efficiency with increasing NaCl concentration, although in terms of growth performances, leaf dry weight, root dry weight, stem length, and total dry weight all decreased with increasing NaCl concentration. Furthermore, leakage of electrolytes, as a consequence of cell membrane damage, clearly increased in response to an increase in NaCl concentration. Analysis of the polyphasic elevation of chlorophyll a fluorescence transients (OKJIP) revealed marked decrease in flux ratios (Φ_PO, Ψ_O and Φ_EO) and the PI_abs, performance index in response to treatment with 200 mM NaCl, thereby reflectings the relatively reduced state of photosystem II. This increase in fluorescence could be due to a reduction in electron transport beyond Q^-_A. We thus found that the photosynthetic parameters, chlorophyll fluorescence and growth characteristics of C. sonchifolium significantly increased in response to treatment with 200 mM NaCl. Conclusions: Collectively, the findings of this study indicate that C. sonchifolium shows relatively low sensitivity to NaCl stress, although photosynthetic activity was markedly reduced in plants exposed to 200 mM NaCl.

• Korean Chemical Engineering Research
• /
• v.47 no.2
• /
• pp.190-194
• /
• 2009

In this study sodium dodecyl sulfate (SDS), which was anionic surfactant, was added for forming micelles to remove iron ion that could be contained with small amount in industrial water. Then aggregates binding between iron ions and micelles were rejected by a ceramic microfiltration membrane. As result of SDS concentration effect on removal rates of iron and SDS in modified iron solution, the removal rate of iron was the highest value of 92.26% and the removal rate of SDS was 61.10% a little higher than the result of calcium ion at 8 mM which was CMC (Critical micelle concentration) of SDS. As final resistance of membrane fouling $R_f$ increased the more at the higher SDS concentration, it showed the highest value at 4 mM and the lowest at 10 mM of SDS. The final permeate flux $J_{180}$ had the highest value and the largest total permeate volume could be finally acquired at SDS 10 mM. In case of CMC 8 mM, low $R_f$ was shown as same as that of 10 mM until 80 minutes of operation, and tended to increase dramatically to 120 minutes and increase slowly again until 180 minutes.

• Journal of Soil and Groundwater Environment
• /
• v.17 no.3
• /
• pp.21-31
• /
• 2012

This paper presents the short-term and long-term measures to determine the fugitive dust concentration in a contaminated site, which is a crucial step for the determination of particulate emission factor (PEF) for risk assessment. As a long-term measure, USEPA method employing Q/C value (inverse of the ratio of the geometric mean air concentration to the emission flux at center of a 0.5-acre square source) seems to be suitable as it reflects regional-specific meteorological conditions. However, it requires nation-wide database collection and interpretation. Use of ASTM method is an alternative as a short-term measure. The method is readily field-applicable as PEF calculation equation is simple and input parameters can be easily derived at the site of interest as well without the nation-wide efforts. Using ASTM method, PEF at the Former Janghang Smelter Site was determined. According to various mode of aggregate size distribution and fractions of vegetative cover, which are the most important factors in PEF calculation, PEF values at the Former Janghang Smelter Site varied greatly. When the mode of aggregate size distribution was set at 0.25 mm, PEF values at the Former Janghang Smelter Site was 5~20 times higher than the default PEF value (i.e., 35 ${\mu}g/m^3$) shown in the current Korean Soil Contamination Risk Assessment Guidance. On contrast, when the mode was set at 2 mm, PEF values at the Former Janghang Smelter Site was 160~640 times lower than the default PEF value in the Korean Guidance.

• Journal of Bio-Environment Control
• /
• v.10 no.4
• /
• pp.232-236
• /
• 2001

Four air temperature levels of 23, 25, 27 and 29$^{\circ}C$, three humidity levels of 85, 90 and 95% R.H. at photosynthetic photon flux (PPF) of 50 $\mu$mol.m$^{-2}$ .s$^{-1}$ were provided to investigate the effect of vapor pressure deficit on the evapotranspiration rate (EVTR) and graft-taking of watermelon grafted seed-increase. Thus EVTR of grafted seedlings increased with increasing air temperature at high humidity of 95%R.H. At relatively low humidity of 85% R.H., grafted seedlings showed a high EVTR and some wilting of scions was observed at this condition. This result would be ascribed to the low supply of water to vascular bundles according to the insufficient joining of scions and rootstocks. Differences in EVTR between 90% R.H. and 95% R.H. were not observed. Grafted seedlings showed high graft-taking at high relative humidity. Relative humidity had highly influenced to the graft-taking as compared to the air temperature. Graft-taking increased with decreasing vapor pressure deficit. Graft-taking greater than 90% was found at vapor pressure deficit less than 0.4kPa which could be obtained at humidity higher than 90% R.H. Therefore it is required to control the humidity higher than 90% R.H. for suppressing EVTR of grafted seedlings and preventing some wilting of scoins and thus enhancing the graft-taking of grafted seedlings.

• Membrane Journal
• /
• v.29 no.6
• /
• pp.348-354
• /
• 2019

Recently, the application range of organic solvent nanofiltration (OSN) technology has been expanding, requiring membranes with better performance. In this work, thin film composite (TFC) OSN membrane was fabricated. First, ultrafiltration support membrane was prepared via nonsolvent-induced phase separation (NIPS) technique using polysulfone (PSf) and polyethersulfone (PES). Then, the effect of pore forming additives such as polyvinylpyrrolidone (PVP) and pluronic F-127 were employed to improve the membrane permeance. The well-known interfacial polymerization technique was employed using MPD-TMC chemistry to form a thin film on top of the fabricated support, and its solvent permeance and nanofiltration performance was characterized. It was found that polyethersulfone support exhibited more reliable performance compared to polysulfone, and PVP additive was more effective compared to Pluronic F-127. As for the oSN performance, polar aprotic solvents like acetonitrile show significantly higher flux (986.5 L·m^-2·h^-1·bar^-1) compared to water and EtOH (9.5 L·m^-2·h^-1·bar^-1).

• Journal of Pharmaceutical Investigation
• /
• v.40 no.5
• /
• pp.305-311
• /
• 2010

The present study was aimed at preparing microemulsion-based hydrogel (MBH) for the skin delivery of itraconazole. Microemulsion prepared with Transcutol as a surfactant, benzyl alcohol as an oil and the mixture of ethanol and phasphatidyl choline (3:2) as a cosurfactant were characterized by solubility, phase diagram, particle size. MBHs were prepared using 0.7 % of xanthan gum (F1-1) or carbopol 940 (F1-2) as gelling agents and characterized by viscosity studies. The in vitro permeation data obtained by using the Franz diffusion cells and hairless mouse skin showed that the optimized microemulsion (F1) consisting of itraconazole (1% w/w), benzyl alcohol (10% w/w), Transcutol (10% w/w) and the mixture of ethanol and phospahtidylcholine (3:2) (10% w/w) and water (49% w/w) showed significant difference in the flux (${\sim}1{\mu}g/cm^2/h$) with their corresponding MBHs (0.25-0.64 ${\mu}g/cm^2/h$). However, the in vitro skin drug content showed no significant difference between F1 and F1-1, while F1-2 showed significantly low skin drug content. The effect of the amount of drug loading (0.02, 1 and 1.5% w/w) on the optimized MBH (F1-2) showed that the permeation and skin drug content increased with higher drug loading (1.5%). The in vivo study of the optimized MBH (F1-2 with1.5% w/w drug loading) showed that this formulation could be used as a potential topical formulation for itraconazole.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.43 no.6
• /
• pp.715-722
• /
• 2010

The effects of temperature, salinity and irradiance on the growth of the harmful red tide dinoflagellate Cochlodinium polykrikoides Margelef isolated from the South Sea of Korea were examined in the laboratory. Growth was examined under the following combinations of temperature and salinity: 15, 20, 25 and $30^{\circ}C$, and 15, 20, 25, 30 and 35 psu at a constant irradiance of $180\;{\mu}mol/m^2/s$. No growth was observed with a temperature of $15^{\circ}C$ and a salinitiy of 15 psu. Moderate growth rates of more than 0.30 /day were obtained at $25^{\circ}C$ with salinities of 25.35 psu. These values are similar to in situ observations for this species. The maximum growth rate, 0.35 /day, was obtained at $25^{\circ}C$ and 30 psu. In light experiments, cell growth of C. polykrikoides was conducted with constant temperature ($20^{\circ}C$) and salinity (30 psu) under light photon flux densities (PFD) of 10, 25, 50, 70, 100, 150, 250 and $350\;{\mu}mol/m^2/s$. C. polykrikoides did not grow at $10\;{\mu}mol/m^2/s$. Cell growth was observed at irradiance values of $25\;{\mu}mol/m^2/s$ and above. The irradiance-growth curve was described as ${\mu}=0.30{\cdot}(I-15.27)/(I+27.22)$, (r=0.99). This suggests a compensation PFD of $15.27\;{\mu}mol/m^2/s$ and a maximum growth rate of 0.30 /day. In conclusion, C. polykrikoides prefers high salinity, temperature and irradiance in summer in Korea. These results provide important information for understanding the mechanism of C. polykrikoides blooms and developing technology to predict blooms of this organism in the field.