• Proceedings of KOSOMES biannual meeting
• /
• 2008.05a
• /
• pp.117-120
• /
• 2008

As we can see at the oil spill occident on the coast of Taean, the viscosity of the spilled oil becomes thicker as time goes by. It becomes waste oil with the form of tar. It moves to other areas following a tide. When the temperature of the water goes up, the viscosity becomes lighter and forms oil film. It repeats the process spreading to and polluting extensive areas where the tide reaches. People have used hand nets to collect waste oil of tar at the sea. But it is very difficult for them to collect the tar type waste oil spread on large areas before it reaches to the beach. This paper tried to find a way to collect the tar type waste oil efficiently. It used absorption mat of boom type that uses the attachment characteristics of the tar type waste oil and floating waste recovery device of net type. It tested the possibility of using the devices at the oil spill accident on the beach of Taean. The result showed that net type recovery device was much more efficient in collecting the waste oil in short time than the hand net system of people. It confirmed that the net type recovery device could be used to collect tar type waste oil.

• Food Science and Preservation
• /
• v.19 no.6
• /
• pp.807-812
• /
• 2012

This study was investigated the changes in quality of heat treated fresh-cut lotus roots using various packaging materials. Lotus roots were purchased from Daegu, Korea. Lotus roots were washed, peeled and sliced with a sharp ceramic knife. The prepared peeled and sliced lotus roots were dipped for 45 sec in water at $55^{\circ}C$. After air-dried at room temperature, the slices were packaged with polyethylene films, polyethylene terephthalate tray+wrapping, vacuum packaging and then stored at $4^{\circ}C$. Changes in weight loss, color, firmness, microorganisms and sensory characteristics were measured. In general, the weight loss rate was increased slightly in vacuum packaged lotus roots. Application of heat treatment delayed browning of lotus roots, and especially vacuum packaged lotus roots were the most lowest ${\Delta}E$ value. However, L and ${\Delta}E$ value of PE film packaged lotus roots were increased highly during storage. The heat treated and vacuum packaging inhibited the growth of microorganisms effectively. The organoleptic quality of vacuum packaged lotus roots showed the best by sensory evaluation.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.6
• /
• pp.776-781
• /
• 2010

Estimating the electrical conductivity of the saturation-paste (SP) is a common method to assess soil salinity. To assess soil salinity realistically, it is important to extract soil solution under field capacity. However, few studies on salinity assessment have been conducted for soil solution extracted under field capacity (-33 kPa; FC) moisture condition due to difficulty in soil solution extraction. This study was conducted to evaluate whether saturation-paste can represent field condition. Soil solutions were extracted from 22 soils in the plastic film house (PFH) and 18 soils in the reclaimed land (RL) at saturation and field capacity moisture conditions. Those were analyzed for pH, EC, cations ($K^+$, $Ca^{2+}$, $Mg^{2+}$, $Na^+$) and anions ($Cl^-$, ${NO_3}^-$, ${PO_4}^{3-}$, ${SO_4}^{2-}$). Both cations and anions of soil solution extracted from FC showed high correlations with ions extracted from SP in the PFH and the RL, except for ${NO_3}^-$, ${PO_4}^{3-}$ in the RL. Results of the t-test, the ECe and $EC_{FC}$ were not significant at significance level 0.05. The slopes of the equations between $EC_{FC}$ and ECe at more than sand 50% soils were higher than less than sand 50% soils, and differences of saturation percentage between SP and FC showed larger as increasing sand percentage. EC was related to soil water retention by soil texture. To determine the EC, soil texture and other soil properties which effect the soil moisture should be considered.

• Journal of Conservation Science
• /
• v.34 no.6
• /
• pp.459-470
• /
• 2018

Cellulose nitrates were used for folklore artifacts(ornamental beads and pipes in hatstrings, frames of eyeglasses, ornamental eyeglass cases, headband ornaments, and jeogori buttons) between the 19th and 20th centuries; however, they are susceptible to cracking, crazing, embrittlement, and crumbling due to deterioration. To consolidate and adhere deteriorated cellulose nitrate folklore artifacts, water-soluble acrylic emulsion adhesives were investigated. For consolidation, Plextol D 498, which has the lowest viscosity in low concentrations, was used. In adhesive films whose glass transition temperature(Tg) is lower than room temperature, the tensile stress and modulus decreased and the strain increased; therefore, the flexibility was high. The Plextol D 498 and Plextol D 498 and Dispersion K 52 films maintained their adhesiveness and flexibility after artificial-sunlight-accelerated ageing, and Plextol D 498 and Dispersion K 52 films hardly caused yellowing. Plextol D 498 was the most stable for accelerating ageing. A low concentration of Plextol D 498 emulsion resulted in the best permeability on the surface of cellulose nitrate, compared with other acrylic emulsions. To prevent ornamental hatstrings from cracking, crazing, embrittlement, and crumbling, a Plextol D 498 emulsion was used. After applying low concentrations(1%, 3%) of the emulsion to consolidate the fragments and high concentration to adhere the fragments, the ornamental hatstrings were protected from crumbling by deterioration, and their fragments were well-adhered. To preserve it from deterioration by oxygen and humidity, the treated ornament was sealed with an oxygen-barrier film using a low-humidity oxygen scavenger.

• Economic and Environmental Geology
• /
• v.55 no.3
• /
• pp.281-293
• /
• 2022

We examined degradation characteristics of lead based pigments(white lead, Red lead, Litharge) according to atmospheric environmet condition, for example atmospheric gas(CO₂, NO₂) and soluble salt. Painted samples not changed material compositions but were occured the color change(𝚫E 4~31) after exposed UV irradiation. All sample were not affected by CO₂ gas not only color but chemical composition. However, samples were remakably changed color exposed NO₂ gas and it was formed secondary product like as lead nitrate. Such as red lead and white lead samples' color difference were 𝚫E 2 and 𝚫 10 respectively and became dark, along with litharge became bright and color difference was 𝚫E 5 after react with NO₂ gas. It confirm that NO₂ was influential factor than CO₂ in the case of same concentration. Furthermore salt spray test was taken to figure out soluble salt influence in fine dust. The result showed noticeable color change and secondary product was formed on samples' surface. The glue film peeled off or hole, and color changed around the secondary products. After salt spray, XRD pattern showed decrease peak intensity and lower crystalinity. As a result of salt spray test, white lead was formed new product litharge and litharge was formed litharge and minium. According to the results, influential atmospheric factors for conservation of paint pigments were UV, NO₂, soluble salt, and litharge was most weakness throughout lead base pigments.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.6
• /
• pp.503-516
• /
• 2021

Autonomous fire detection and suppression system requires advanced technology for complex detection technology and injection/control technology for accurate hitting by fire location. Also, foam spraying should be included to respond to oil fires. However, when a single spray monitor is used in common, water and foam spray properties appear different, so for accurate fire suppression, research on the spray trajectory and distance will be required. In this study, experimental studies and numerical analysis studies were combined to analyze the foam spray characteristics through the spray monitor developed for the establishment of an autonomous fire extinguishing system. For flow analysis of foam injection, modeling was performed using OpenFOAM analysis software, and the commonly used foaming agent (Aqueous Film-Forming Foam) was applied for foam properties. The injection distance analysis was performed according to the injection pressure and the injection angle according to the form of the foam, and at the same time, the results were verified and presented through the injection experiment.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.spc
• /
• pp.23-29
• /
• 2022

To detect harmful chemical substances in seawater, we fabricated a prototype sensor and evaluated its performance. The prototype sensor consisted of a detector, housing, and driving circuit. We built the detector by printing an Indium-Tin-Oxide (ITO) nanoparticle film on a flexible substrate, and it had two detection parts for simultaneous detection of temperature and HNS concentration. The housing connected the detector and the driving circuit and was made of Teflon material to prevent chemical reactions that may affect sensor performance. The driving circuit supplied electric power, and display measured data using a bridge circuit and an Arduino board. We evaluated the sensor performances such as response (ΔR), the limit of detection (LOD), response time, and errors to confirm the specification.

• Fisheries and Aquatic Sciences
• /
• v.26 no.8
• /
• pp.500-513
• /
• 2023

The effects of prolonged photoperiod (additional night lighting) were investigated on the production of Ocimum basilicum (lemon basil) and fish/crayfish raised in a nutrient film technique aquaponic system. Hybrid lemon fin barb and red claw crayfish juveniles were co-cultured with O. basilicum and subjected to 12 h of ambient natural daylight and additional 0, 4, 8, and 12 h of night lighting for 14 weeks (two batches of 7 weeks each). The water quality parameters and the performance characteristics of the fish/crayfish/plant were evaluated, and the nutri- ent uptake (nitrogen, phosphorus, and potassium) in the system by the three organisms was also measured. The fish growth performance showed no significant differences (p > 0.05) in all the growth parameters measured across the treatments. The body proximate and nitrogen, phosphate, and potassium (NPK) composition of the fish and crayfish were not significantly (p > 0.05) different across the treatments. Similarly, there was no significant difference (p > 0.05) in the NPK uptake by the fish and crayfish across the treatments. The plant growth performance showed that there were no significant (p > 0.05) differences in the plant growth parameters measured, except for % plant height gained in the 12 h-light treatment (403.2 ± 26.0%) which was significantly (p < 0.05) higher than other treatments and cycles. Hence, this study demonstrat- ed that varying supplementary night lighting has no significant effect on the growth performance of O. basilicum, hybrid lemon fin barb, and red claw crayfish. This study, therefore, suggests that supplementary night lighting should not be considered for O. basilicum production as it does not significantly improve the performance characteristics of the plant nor the fish co-cultured with it in a polyculture aquaponic system.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.3
• /
• pp.116-123
• /
• 2023

A high intensity focuses ultrasound (HIFU) is one of the emerging technologies in the biomedical field. The piezoelectric HIFU transducer is a device that utilizes the thermal energy generated by high ultrasound energy. Recently an operating frequency of the HIFU transducer is to expand above a 7 MHz. In this study, the acoustic pressures and temperature distributions in the tissue that generated by the HIFU transducer at 10 MHz were calculated with the finite element method. In addition, the pressure focusing characteristics of the device were analyzed. The geometrical variables are the piezomaterial thickness, lens shape, water height, and film thickness. The results shown that the acoustic pressure increased and saturated gradually when the height/radius (H_L/R_L) ratio of the lens increased. Moreover, the focal area was gradually decreases with H_L/R_L ratio of the lens. In case of the optimized HIFU transducer, the maximum pressure and temperature were analyzed about 19 MPa and 65℃ respectively. And the -3 dB focused distances in the axial and lateral direction are around 2.3 mm and 0.23 mm respectively.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.3
• /
• pp.344-352
• /
• 2012

Soil physical properties determine soil quality in aspect of root growth, infiltration, water and nutrient holding capacity. Although the monitoring of soil physical properties is important for sustainable agricultural production, there were few studies. This study was conducted to investigate the condition of soil physical properties of arable land according to land use across the country. The work was investigated on plastic film house soils, upland soils, orchard soils, and paddy soils from 2008 to 2011, including depth of topsoil, bulk density, hardness, soil texture, and organic matter. The average physical properties were following; In plastic film house soils, the depth of topsoil was 16.2 cm. For the topsoils, hardness was 9.0 mm, bulk density was 1.09 Mg $m^{-3}$, and organic matter content was 29.0 g $kg^{-1}$. For the subsoils, hardness was 19.8 mm, bulk density was 1.32 Mg $m^{-3}$, and organic matter content was 29.5 g $kg^{-1}$; In upland soils, depth of topsoil was 13.3 cm. For the topsoils, hardness was 11.3 mm, bulk density was 1.33 Mg $m^{-3}$, and organic matter content was 20.6 g $kg^{-1}$. For the subsoils, hardness was 18.8 mm, bulk density was 1.52 Mg $m^{-3}$, and organic matter content was 13.0 g $kg^{-1}$. Classified by the types of crop, soil physical properties were high value in a group of deep-rooted vegetables and a group of short-rooted vegetables soil, but low value in a group of leafy vegetables soil; In orchard soils, the depth of topsoil was 15.4 cm. For the topsoils, hardness was 16.1 mm, bulk density was 1.25 Mg $m^{-3}$, and organic matter content was 28.5 g $kg^{-1}$. For the subsoils, hardness was 19.8 mm, bulk density was 1.41 Mg $m^{-3}$, and organic matter content was 15.9 g $kg^{-1}$; In paddy soils, the depth of topsoil was 17.5 cm. For the topsoils, hardness was 15.3 mm, bulk density was 1.22 Mg $m^{-3}$, and organic matter content was 23.5 g $kg^{-1}$. For the subsoils, hardness was 20.3 mm, bulk density was 1.47 Mg $m^{-3}$, and organic matter content was 17.5 g $kg^{-1}$. The average of bulk density was plastic film house soils < paddy soils < orchard soils < upland soils in order, according to land use. The bulk density value of topsoils is mainly distributed in 1.0~1.25 Mg $m^{-3}$. The bulk density value of subsoils is mostly distributed in more than 1.50, 1.35~1.50, and 1.0~1.50 Mg $m^{-3}$ for upland and paddy soils, orchard soils, and plastic film house soils, respectively. Classified by soil textural family, there was lower bulk density in clayey soil, and higher bulk density in fine silty and sandy soil. Soil physical properties and distribution of topography were different classified by the types of land use and growing crops. Therefore, we need to consider the types of land use and crop for appropriate soil management.