• Korean Journal of Optics and Photonics
• /
• v.22 no.6
• /
• pp.283-290
• /
• 2011

A Raman LIDAR system has been designed and constructed for quantitative measurement of water vapor mixing ratio. The comparison with commercial microwave radiometer and global navigation satellite system(GNSS) was performed for the precipitable water vapor(PWV) profile and total PWV. The result shows that the total GNSS-PWV and LIDAR-PWV have good correlation with each other. But, there is small difference between the two methods because of maximum measurement height in LIDAR and the GNSS method. There are some significant differences between Raman and MWR when the water vapor concentration changes quickly near the boundary layer or at the edge of a cloud. Finally we have decided that MWR cannot detect spatial changes but LIDAR can measure spatial changes.

• Korean Journal of Food Science and Technology
• /
• v.34 no.6
• /
• pp.1023-1029
• /
• 2002

Relationship between RVA properties and physical properties of film made from native corn starch and hydroxypropylated corn starch at various levels of plasticizers was examinel. Tensile strength of the film decreased, but its elongation and water vapor permeability increased with increasing plasticizer concentration. The film with glycerol showed greater changes in physical properties than that with sorbitol. Hydroxypropylated starch film showed lower tensile strength, higher elongation, and higher water vapor permeability than the native starch film. Sorbitol resulted in films with relatively high tensile strength, whereas glycerol produced films with increased elongation. The most reliable parameters for the relationship between RVA properties and film properties were RVA peak viscosity, tensile strength, and water vapor permeability. Water vapor permeability and tensile strength had linear relationship with RVA properties. The tensile strength and water vapor permeability of film could be predicted using the RVA peak viscosity.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.238.2-238.2
• /
• 2015

Surface modification of vertically-aligned carbon nanotube (VACNT) is essential in order to meet specific demands for particular applications such as field emission displays, heat dissipation device and potential sun energy conversion due to their superior electrical and thermal conductivity and strong light absorption. In this study, we observe the effect of exposure to water vapor on a different lengths of the surfaces of VACNT. The study was conducted on three different lengths of the VACNT: short length around $200{\mu}m$, medium-length around $500{\mu}m$, and high length around 1 mm. Water exposure time ranges between 2-10 min and temperature of the water ranges from 60 to 120 oC. The result of water vapor exposure mainly show that increasing the exposure time and water temperature give rise to increase of the speed of change on the surface of the VACNT. Especially, the shorter VACNT change their surface morphology most rapidly.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.304-310
• /
• 2001

A numerical model which simulates the heat and mass transfer processes within a counter-current plate type generator for ammonia/water absorption refrigerators was developed. Ammonia/water solution flows downward under gravity and ammonia/water vapor generated by flow boiling flows upward. The flow pattern within the generator was assumed to be a bubbly flow, and the liquid and vapor phase were assumed to be saturated. It was shown that the boiling of ammonia occurred mainly in the upper part of the generator. The effects of the generator length, the wall temperature and the mass flow rate of ammonia/water solution into the generator on the generation of ammonia/water vapor were investigated.

• Journal of Applied Biological Chemistry
• /
• v.43 no.2
• /
• pp.79-85
• /
• 2000

Biodegradable films were prepared from roasted sesame meal and rice bran. Acetic anhydride, succinic anhydride, and formaldehyde were added to the film-forming solutions, and their effects on tensile strength, percent elongation, water vapor permeability, and water solubility of the films were studied. Roasted sesame meal did not form film without acylation or addition of formaldehyde. Acylated roasted sesame films had higher tensile strength and water-solubility, and lower % elongation than rice bran films. Acylation with acetic and succinic anhydrides increased tensile strength, percent elongation, and water solubility of rice bran films, but decreased water vapor permeability. Treatment with formaldehyde increased tensile strength of roasted sesame and rice bran films and % elongation of rice bran films, while reducing water-solubility of roasted sesame and rice bran films and water vapor permeability of rice bran films.

• Membrane Journal
• /
• v.22 no.5
• /
• pp.369-380
• /
• 2012

A one-dimensional numerical model based on the energy and mass equations have been developed to predict the trans membrane water vapor flux and thermal efficiency under various operating conditions in Direct Contact Membrane Distillation (DCMD) process. The model validation have been carried out by experimental data from literature and showed good agreement. The effect of operating parameters such as brine inlet temperature and velocity, and distillate inlet temperature and velocity to increase water vapor flux and thermal efficiency were predicted by the steady-state model. The results showed that the inlet temperature and velocity in brine side are dominant factors to control the water vapor flux and thermal efficiency because the effect of inlet temperature and velocity in brine side showed the higher water vapor flux and thermal efficiency than that of inlet temperature and velocity in distillate side. The water vapor flux was increased 3.4 times in the range of 21.22 $kg/m^2h$ to 71.26 $kg/m^2h$ and the thermal efficiency was increased 37.5% in that of 0.556 to 0.765 with increasing brine inlet temperature from $60^{\circ}C$ to $95^{\circ}C$. Meanwhile, the water vapor flux was increased 30% in that of 27.91 $kg/m^2h$ to 36.33 $kg/m^2h$ and thermal efficiency increased 7.5% in that of 0.6 to 0.646 as the brine inlet velocity was increased from 60 m/h to 300 m/h.

• Fibers and Polymers
• /
• v.3 no.4
• /
• pp.153-158
• /
• 2002

A series of waterborne polyurethanes (WBPU) were prepared from 4,4-dicyclohexylmethane diisocyanate ($H_{12}$MDI),2,2-bis(hydroxylmethyl) propionic acid (DMPA), othylenediarnine (EDA), triethylamine (TEA), and triblock glycol [TBG, ($\varepsilon$-caprolactone)$_{4.5}$-poly(tetramethylene ether) glycol (MW= 2000)-($\varepsilon$-caprolactone)$_{4.5}$: $(CL)_{4.5}$-PTMG-$(CL)_{4.5}$, MW=3000] as a soft segment. Two melting peaks of TBG at about 14$^{\circ}C$ and 38$^{\circ}C$ were observed indicating the presence of two different crystalline domains composed of CL and PTMG dominant component. The effect of soft segment content (60-75 wt%) on the colloidal properties of dispersion, and thermal and mechanical properties of WBPU films, the water vapor permeability (WVP) and water resistance (WR) of WBPU-coated Nylon fabrics, and the adhesive strength of WBPU- coated layer and Nylon fabrics was investigated. As soft segment contents increased, the water vapor permeability of WBPU- coated Nylon fabrics increased from 3615 to 4502 g/$m^2$day, however, the water resistances decreased from 1300 to 500 mm$H_2$O.O.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.1036-1038
• /
• 2003

Diurnal variations in the atmospheric vapor at Banchiao of Taiwan are studied by analyzing 30 min-averaged data in the summer of 1998. The surface meteorological measurements were mainly obtained from the Central Weather Bureau (CWB) of Taiwan. It is found that precipitable water (PW) is increased in the afternoon. The maximum of precipitable water appears at around 0900 LST. The diurnal range of precipitable water is larger on the days with than without rainfall events. Rainfall events often occur in the afternoon and early morning. We also examine the difference in the characteristics of the PW signatures with and without rainfall according to the occurrence of the times for the rainfall peak and the onset of rainfall.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.5
• /
• pp.191-198
• /
• 1998

In this study, the effects of water vapor in inlet air, spark advance and fuel type in the spark ignition engine were investigated through the experiments of combustion and flame arriving pattern analysis using ionization probe. The results of flame propagation experiment using ionization probe show that the flame which ignited from spark plug located at the center of the combustion chamber propagated faster in exhaust side than in intake side due to the mixture flow motion inducted into combustion chamber from intake tumble port at all conditions. And as the partial vapor pressure increased, the flame propagation became slower in all direction. Especially effects were greater for intake side than the exhaust side.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.22-23
• /
• 2006

A process for removal of photoresist(PR) m semiconductor manufacturing using water vapor with ozone is presented. For the realization of the ozone/vapor mixture process, high concentration ozone generator and process facilities have developed. As a result of the silicon wafer PR strip test, we confirmed the high efficiency PR strip rates of 400nm/mm or more at the ozone concentration of 16wt%/$O_2$. The ozone/vapor mixture process is more effective than the ozonized water Immersion process.