• Ocean Systems Engineering
• /
• v.2 no.1
• /
• pp.33-47
• /
• 2012

This study revealed the behavior of droplets formed through leak process in deep water. There was a threshold depth named the universal attraction depth (UAD). Droplets rose upward in the zone below the UAD called the rising zone, and settled down in the zone above the UAD called the settling zone. Three mass loss modes were identified and formulated: dissolution induced by mass transfer, condensation by heat transfer and phase separation by pressure decrease. The first two were active for the settling zone, and all the three were effective for the rising zone. In consequence, the life time of the droplets in the rising zone was far shorter than that of the droplets in the settling zone.

• Journal of ILASS-Korea
• /
• v.25 no.2
• /
• pp.68-73
• /
• 2020

In the present study, experiments on the film boiling of liquid droplets on oxidized copper surface was conducted. The shape of pure water droplets was observed, and the evaporation rate of them was measured during the film boiling evaporation process. The droplet of initial volume 16 ~ 30 µl was applied onto the oxidized copper surface heated up to 300 ~ 500℃, then the shape of the droplet was analyzed during the film boiling evaporation. Experimental results showed that there was good correlation between dimensionless volume and dimensionless time. However, a significant difference in evaporation rate for small and large droplets discussed in previous study was not found.

• Journal of the Korean Society of Visualization
• /
• v.22 no.2
• /
• pp.82-89
• /
• 2024

In this study, experiments were conducted to visualize and analyze the dynamic characteristics of splash and residual liquid film formation during and after the injection of water droplets onto vertically situated solid substrates with varying surface wettability, elasticity, and microtexture. As wettability decreased (higher contact angle), more splash droplets formed, and the residual liquid film decreased. Low contact angles resulted in thin residual films and less splash. Surface elasticity absorbed the impact forces of droplets, thereby decreasing splash phenomena and significantly reducing the formation of residual liquid films due to surface vibration. Surfaces with microtextures demonstrated control over droplet splash direction, guiding the liquid along desired pathways. High-speed imaging provided detailed insights, showing that surface properties critically influence splash dynamics and residual liquid film formation.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.04a
• /
• pp.159-164
• /
• 2009

The water droplet motion and the interaction between the droplets in a PEMFC air flow channel with multiple pores, through which water emerges, is studied numerically by solving the equations governing the conservation of mass and momentum. The liquid-gas interface is tracked by a level set method which is based on a sharp-interface representation for accurately imposing the matching conditions at the interface. The method is modified to implement the contact angle conditions on the walls and pores. The dynamic interaction between the droplets growing on multiple pores while keeping the total water flow rate through pores constant is investigated by conducting the computations until the droplet motion exhibits a periodic pattern. The numerical results show that the droplet merging caused by increasing the number of pores is not effective for water removal and that the contact angle of channel wall strongly affects water management in the PEMFC air flow channel.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.18-24
• /
• 2005

Wet compression means the injection of water droplets into the compressor of gas turbines. This method decreases the compression work and increases the turbine output by decreasing the compressor exit temperature through the evaporation of water droplets inside the compressor. This paper provides thermodynamic and aerodynamic analysis on wet compression in a centrifugal compressor for a microturbine. The meanline performance analysis of centrifugal compressor is coupled with the thermodynamic equation of wet compression to get the meanline performance of wet compression. The most influencing parameter in the analysis is the evaporative rate of water droplets. It is found that the impeller exit flow temperature and compression work decreases as the evaporative rate increases. And the exit flow angle decreases as the evaporative rate increases.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1534-1539
• /
• 2004

This experiment has been carried out to measure the process of droplet formation between water phase fluid(PVA 3%) and organic phase fluid(oil) and vector fields measured by a Dynamic Micro-PIV method in the inside of a droplet while generated. Droplet length controlled by changing flow rate conditions in microchannel. Water-in-oil(W/O) droplets successfully generated at a Y junction and cross microchannel. But oil-in-water(O/W) droplets could not be formed at a Y junction microchannel. That is, PVA 3% flow could not be detached from the PDMS surface and ran parallel with oil flow. When PVA 3% flow rate was constant, droplet length and time period decreased as oil flow rate increased, but droplet frequency increased. When PVA 3% and oil flow rate ratio was constant, droplet length and time period decreased as flow rate increased, but droplet frequency increased. All that case, Standard deviation of droplet formation have less than 5% at averaged droplet length and regular-sized droplets were reproducibly formed.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.25 no.4 s.34
• /
• pp.65-74
• /
• 1999

We have studied the stability of W/O high internal phase emulsions(HIPE) containing water, cetyl dimethicone copolyol and oils varying magnesium sulfate in the range 0 to 0.5 wt% and oil polarities, respectively. The rheological consistency was mainly destroyed by the coalescence of the deformed water droplets. The greater the increase of complex modulus was, the less coalescence occurred and the more consistent the concentrated emulsions were. The increasing pattern of complex modulus versus volume fraction has been explained with the resistance to coalescence of the deformed interfacial film of water droplets in concentrated W/O emulsion. The stability is dependent on: (i) the choice of the oil is important, the requirements coincide with the requirements for the formation of the rigid liquid crystalline phases; and (ii) addition of salts the aqueous phase opposes the instability due to coalescence. Increasing the salt concentration increases the refractive index of the aqueous phase. It lowers the difference in the refractive index between the oil and aqueous phases. This decreases the attraction between the water domains, thus increasing the stability.

• Journal of the Korean Society of Combustion
• /
• v.5 no.1
• /
• pp.81-89
• /
• 2000

An experimental study has been carried on single fuel droplets of water-in-light oil emulsions in an electric furnace to elucidate the dominant factor for the occurrence of micro-explosions. The tests were carried out by changing the following four parameters; the surfactant, the ratio of water to light oil, ambient temperature in electric furnace, and four kinds of fuels having different viscosity(light-oil, kerosene, iso-octane, bunker fuel). The result shows that micro-explosion phenomena is dominated without surfactant and below 30% of water content. Explosion-time is affected by ambient temperature and viscosity of used fuel.

• Proceedings of the SCSK Conference
• /
• 1999.10a
• /
• pp.65-74
• /
• 1999

We have studied the stability of W/O high internal phase emulsions(HIPE) containing water, cetyl dimethicone copolyol and oils varying magnesium sulfate in the range 0 to 0.5wt% and oil polarities, respectively. The rheological consistency was mainly destroyed by the coalescence of the deformed water droplets. The greater the increase of concentrated modulus was, the less coalescence occurred and the more consistent the concentrated emulsions were. The increasing pattern of complex modulus versus volume fraction has been explained with the resistance to coalescence of the deformed interfacial film of water droplets in concentrated W/O emulsion. The stability is dependent on: (i) the choice of the oil is important, the requirements coincide with the requirements for the formation of the rigid liquid crystalline phases :5; and (ii) addition of salts the aqueous phase opposes the instability due to coalescence:. Increasing the salt concentration increases the refractive index of the aqueous phase. It lowers the difference in the refractive index between the oil and aqueous phases. This decreases the attraction between the water domains, thus increasing the stability.

• Journal of Ceramic Processing Research
• /
• v.13 no.spc1
• /
• pp.145-148
• /
• 2012

Spherical silica aerogel powders were fabricated via an emulsion polymerization method from a water glass. A water-in-oil emulsion, in which droplets of a silicic acid solution are emulsified with span 80 (surfactant) in n-hexane, was produced by a high power homogenizer. After gelation, the surface of the spherical silica hydrogels was modified using a TMCS (trimethylchlorosilane)/n-hexane solution followed by solvent exchange from water to n-hexane. Hydrophobic silica wet gel droplets were dried at 80 ℃ under ambient pressure. A perfect spherical silica aerogel powder between1 to 12 ㎛ in diameter was obtained and its size can be controlled by mixing speed. The tapping density, pore volume, and BET surface area of the silica aerogel powder were approximately 0.08 g·cm-3, 3.5 ㎤·g-1 and 742 ㎡·g-1, respectively.