• Journal of Korean Society for Atmospheric Environment
• /
• v.28 no.1
• /
• pp.39-51
• /
• 2012

Aerosol slurry samples were collected in 60-min interval using Korean Semi-continuous Elements in Aerosol Sampler (KSEAS) between May 19 and June 6, 2010 at an urban site of Gwangju. The $PM_{2.5}$ samples were collected with a flow rate of 16.7 L/min and particles are grown by condensation of water vapor in a condenser maintained at ${\sim}5^{\circ}C$ after saturation by direct injection of steam. The resulting droplets are collected in a liquid slurry with a airdroplet separator. Concentrations of 16 elements (Al, Fe, Mn, Ca, K, Cu, Zn, Pb, Cd, Cr, Ti, V, Ni, Co, As, Se) in the collected slurry samples were determined off-line by ICP-MS. KSEAS sample analysis encompassed the sampling periods for which 24-hr average elemental species concentrations were calculated for comparison with those derived from 24-hr integrated filter samples. Relationship between elemental species measured by two methods indicated high correlation coefficients (r), mostly greater than r of 0.80. However, we note that concentrations of Al, K, Ca, Mn, and Fe, which are often associated with crustal elemental particles, in the KSEAS samples, were substantially lower (1.4~11 times) than those found in the typical filter-based samples. This discrepancy is probably due to difficulties in transferring insoluble dust particles to the collection vials in the KSEAS. Temporal profiles of elemental concentrations indicate that some transient events in their concentrations are observed over the sampling periods. For the elemental species studied, atmospheric concentrations during the transient events increased by factors of 4 in Mn~80 in Zn, compared to their background levels. Principle component analyses were applied to the hourly KSEAS data sets to identify sources affecting the concentrations of the metal constituents observed. In this study, we conclude that hourly measurements for particle-bound elemental constituents were extremely useful for revealing the short-term variability in their concentrations and developing insights into their sources.

• Macromolecular Research
• /
• v.14 no.4
• /
• pp.466-472
• /
• 2006

The kinetic behavior of emulsion polymerizations of styrene in the presence of sulfonated N-hydroxy ethyl aniline (SHEA) was investigated with two initiators: 2,2'-azobisisobutyronitrile (AIBN) and potassium persulfate (KPS). SHEA was synthesized using a stepwise polyurethane reaction method from 3-hydroxy-1-propane sulfonic acid sodium salt, isophorone diisocyanate (IPDI), and N-(2-hydroxyethyl) aniline. Stable core-shell poly(styrene/sulfonated N-hydroxy ethyl aniline, St/SHEA) latex particles were successfully prepared by using an appropriate amount of AIBN, in which SHEA plays the role of 'surfmer', i.e., acting as both a surfactant in the emulsion polymerization and a monomer in the chemical oxidative polymerization. The kinetic behavior was dissimilar to that of typical emulsion polymerization systems. A long inhibition period and low rate of polymerization were observed due to radical loss by the oxidative polymerization of SHEA. It was concluded, due to the low water-solubility of AIBN and retardation reaction by SHEA, that the initial loci of polymerization were monomer droplets. However, growing polymer particles as polymerization loci became predominant as polymerization proceeded. It was suggested that AIBN was more effective than KPS in the preparation of the core-shell type poly(St/SHEA) latex particles. With KPS, no substantial polymerization was observed in any of the samples.

• Journal of Powder Materials
• /
• v.8 no.3
• /
• pp.151-156
• /
• 2001

MgO based nanocomposite powder including ferromagnetic iron particle dispersions, which can be available for the magnetic and catalytic applications, was fabricated by the spray pyrolysis process using ultra-sonic atomizer and reduction processes. Liquid source was prepared from iron (Fe)-nitrate, as a source of Fe nano-dispersion, and magnesium (Mg)-nitrate, as a source of MgO materials, with pure water solvent. After the chamber were heated to given temperatures (500~$^800{\circ}C$), the mist of liquid droplets generated by ultrasonic atomizer carried into the chamber by a carrier gas of air, and the ist was decomposed into Fe-oxide and MgO nano-powder. The obtained powders were reduced by hydrogen atmosphere at 600~$^800{\circ}C$. The reduction behavior was investigated by thermal gravity and hygrometry. After reduction, the aggregated sub-micron Fe/MgO powders were obtained, and each aggregated powder composed of nano-sized Fe/MgO materials. By the difference of the chamber temperature, the particle size of Fe and MgO was changed in a few 10 nm levels. Also, the nano-porous Fe-MgO sub-micron powders were obtained. Through this preparation process and the evaluation of phase and microstructure, it was concluded that the Fe/MgO nanocomposite powders with high surface area and the higher coercive force were successfully fabricated.

• International Journal of Aeronautical and Space Sciences
• /
• v.4 no.1
• /
• pp.63-74
• /
• 2003

The vortical flow of a 65-deg flat plate delta wing with a leading edge extension(LEX) was examined through off-surface visualization, 5-hole probe and hot-film measurements. The off-surface flow visualization technique used micro water droplets generated by a home-style ultrasonic humidifier and a laser beam sheet. The angles of attack ranged from 10 to 30 degrees, and the sideslip angles ranged from 0 to -15 degrees. The Reynolds number was $1.82{\times}10^5$ for the flow visualization, and $1.76{\times}10^6$ for the 5-hole probe and hot-film measurements. The comparison of the visualization photos and the flow field measurement showed that the two results were in a good agreement for the relative position and the structure of the wing and LEX vortices, even though the flow Reynolds numbers of the two results were much different. The wing vortex and the LEX vortex coil each other while maintaining a comparable strength and identity at zero sideslip. Neither a looping of the wing vortex around the strake vortex, nor the lopsided coiling of the stronger strake and the weaker wing vortices was observed. At non-zero sideslip, the downward movement of the LEX vortex when going downstream was enhanced on the windward side, and the downward and inboard movement of the LEX vortex when going downstream was suppressed on the leeward side. The counterclockwise coiling of the wing and LEX vortices was decreased significantly on the leeward side.

• Nuclear Engineering and Technology
• /
• v.22 no.4
• /
• pp.326-336
• /
• 1990

Recent experiments show the existence of spacer grid improves the heat removal from the fuel rods during the reflood phase of LOCA. The local heat transfer within and downstream of the grid is increased due to the earlier quenching than rod surface, shattering of the entrained droplets into smaller ones which can be more easily evaporated and enhanced turbulent effect. Therefore, the consideration of these phenomena is necessary for the DFFB regime which prevails above the water level during the reflood. In this paper, droplet breakup model at spacer grid has been developed and incorporated into RELAP5/MOD2. Verification calculations are carried out for FEBA tests which examine the thermalhydraulic performance of grid spacer during reflood.

• Corrosion Science and Technology
• /
• v.15 no.4
• /
• pp.182-188
• /
• 2016

Significant piping wall thinning caused by Flow-Accelerated Corrosion (FAC) and Erosion-Corrosion (EC) continues to occur, even after the Mihama Power Station unit 3 secondary pipe rupture in 2004, in which workers were seriously injured or died. Nuclear power plants in many countries have experienced FAC and EC-related cases in steam cycle piping systems. Korea has also experienced piping wall thinning cases including thinning in the downstream straight pipe of a check valve in a feedwater pump line, the downstream elbow of a control valve in a feedwater flow control line, and failure of the straight pipe downstream of an orifice in an auxiliary steam return line. Cause analyses were performed by reviewing thickness data using Ultrasonic Techniques (UT) and, Scanning Electron Microscope (SEM) images for the failed pipe, and numerical simulation results for FAC and EC cases in Korea Nuclear Power Plants. It was concluded that the main cause of wall thinning for the downstream pipe of a check valve is FAC caused by water vortex flow due to the internal flow shape of a check valve, the main cause of wall thinning for the downstream elbow of a control valve is FAC caused by a thickness difference with the upstream pipe, and the main cause of wall thinning for the downstream pipe of an orifice is FAC and EC caused by liquid droplets and vortex flow. In order to investigate more cases, additional analyses were performed with the review of a lot of thickness data for inspected pipes. The results showed that pipe wall thinning was also affected by the operating condition of upstream equipment. Management of FAC and EC based on these cases will focus on the downstream piping of abnormal or unusual operated equipment.

• Korean journal of applied entomology
• /
• v.59 no.2
• /
• pp.83-91
• /
• 2020

We assessed efficacy of spraying pesticides from an unmanned helicopter to control two insect species, Monochamus alternatus and M. saltuarius, which are vectors of pine wood nematodes. Control efficacy of thiacloprid FL (33×), acetamiprid ME (33×), and flupyradifurone SL (33×) was determined by placing caged insects in the canopy of pine trees (Pinus sp). Water-sensitive paper was used to record the spray pattern of pesticide droplets and the degree of coverage; furthermore, we investigated peripheral scattering due to spraying. The three pesticides showed > 96% control efficacy against the targeted vectors, and pesticide droplet spray patterns were similar. Peripheral scattering was observed up to 20 m in front and 10 m to the left, right, and behind the targeted area. The coverage index of all the directions at 5 and 10 m distance was 6-7 and 2, respectively.

• Journal of the Korean Chemical Society
• /
• v.26 no.2
• /
• pp.88-94
• /
• 1982

The concentrations of gaseous ammonia and particulate ammonium emitted from a urea plan were measured, and the conversion rate of ammonia to ammonium was estimated. The conversion of ammonia to ammonium has two stages with transport time in the atmosphere. In the initial 15min the conversion rate was 3.2% min$^{-1}$, and thereafter 0.26% min$^{-1}$. The high conversion rate of ammonia to ammonium at the initial period of it's transport might be due to the dissolution of ammonia into water droplets formed by the decrease in temperature of the stack effluent. The concentration of ammonium is further increased by the decomposition of urea in alkaline droplet formed. Half-lives of ammonia gas at initial and latter slag were 16 min and 192 min respectively. No correlation of particulate ammonium concentration to temperature, relative humidity, and concentrations of sulfur dioxide, nitrogen oxides and airborne particulate matter were found in this field measurement.

• Korean Chemical Engineering Research
• /
• v.51 no.5
• /
• pp.597-601
• /
• 2013

In this study, we present simple microfluidic approach for the synthesis of monodisperse microcapsules by using droplet-based system. We generate double emulsion through single step in the microfluidic device having single junction while conventional approaches are limited in surface treatment for the generation of double emulsion. First, we have injected disperse fluid containing FC-77 oil and photocurable ethoxylated trimethylolpropane triacrylate (ETPTA) and water containing 3 wt% poly(vinyl alcohol) (PVA) as continuous phase into microfluidic device. Under the condition, we easily generate double emulsion with high monodispersity by using flow focusing. The double emulsion droplets are transformed into microcapsules under the UV irradiation via photopolymerization. In addition, we control thickness of double emulsion's shell by controlling flow rate of ETPTA. We also show that the size of double emulsions can be controlled by manipulation of flow rate of continuous phase. Furthermore, we synthesize microcapsules encapsulating various materials for the application of drug delivery systems.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1621-1622
• /
• 2006

This paper presents the effect of driving waveform for piezoelectric bend mode inkjet printhead with optimized mechanical design. Experimental and theoretical studies on the applied driving waveform versus jetting characteristic s were performed. The inkjet head has been designed to maximize the droplet velocity, minimize voltage response of the actuator and optimize the firing frequency to eject ink droplet. The head design was carried out by using mechanical simulation. The printhead has been fabricated with Si(100) and SOI wafers by MEMS process and silicon direct bonding method. To investigate how performance of the piezoelectric ceramic actuator influences on droplet diameter and droplet velocity, the method of stroboscopy was used. Also we observed the movement characteristics of PZT actuator with LDV(Laser Doppler Vibrometer) system, oscilloscope and dynamic signal analyzer. Missing nozzles caused by bubbles in chamber were monitored by their resonance frequency. Using the water based ink of viscosity of 4.8 cps and surface tension of 0.025N/m, it is possible to eject stable droplets up to 20kHz, 4.4m/s and above 8pL at the different applied driving waveforms.