• 설비공학논문집
• /
• 제10권4호
• /
• pp.475-482
• /
• 1998

In this paper, an experimental study was conducted to investigate the performance of the spherical ice particle production system which uses the technology of water spray in a vacuum chamber for increasing the heat transfer area. As a result, following conclusions were obtained. The diffusion-controlled evaporation model agreed relatively well with experiments. The spray flow rate influences the performance of the system rather than any other factors, for example, the spray nozzle position, the nozzle number. As the spray rate increases, the system efficiency increases. It is due to the entrainment of small droplets among the spray with the exhausted vapor. Thus the system should be designed and operated to prevent the entrainment. Assuming the compressor efficiency to be 70%, the COP of the system reaches highly up to 6 at a maximum spray rate. Under the conditions, however, the rigid ice layer is obtained because ice particles bond together with increase of the spray rate. Therefore, the spray rate should be controlled properly to make the spherical ice particles.

• 에너지공학
• /
• 제9권3호
• /
• pp.261-268
• /
• 2000

A heat transfer correlation to predict the vaporization of a water droplet in highly superheated steam during a loss-of-coolant accident(LOCA) of a nuclear power plant is provided. Vaporization of liquid fuel or water droplets in superheated air or steam and subsequent interface heat transfer between a liquid droplet and superheated gas is typically correlated by way of a Nusselt number as a function of Reynolds number, Prantl number, and in some cases including mass transfer number. Presently available correlations and experimental data of the evaporation of liquid droplets in air or steam are analyzed and a new Nusselt number correlation is proposed taking Schmidt number into consideration in order to account for binary diffusion of the vapor as well, Nu$\_$f/(1+B)$\^$0.7/=2+0.53Sc$\_$f/$\^$-1/5/Re$\_$M/$\^$$\sfrac{1}{2}$/Pr$\_$f/$\^$$\sfrac{1}{3}$/ for which properties are evaluated at film condition except the density of Reynolds number evaluated at ambient condition. Diverse correlations for various combinations of liquid and gas species are put into single equation. The blowing correction factor of (1+B)$\^$0.7/ is confirmed appropriate, and a criterion to distinguish so-called high- and low-temperature condition of ambient gas is set forth.

• International Journal of Precision Engineering and Manufacturing
• /
• 제8권2호
• /
• pp.75-79
• /
• 2007

This paper describes the self-alignment and bonding of microparts using adhesive surface tension to assemble microsystems in air. The alignment and bonding were tested experimentally using adhesive droplets, and the resulting performance was evaluated. The adhesive, which was inorganic and water-soluble before hardening, was diluted with water to a ratio of 10:1 so that its surface tension generated a sufficient restoring force for self-alignment. The experimental results showed that the average of the alignment errors obtained using the adhesive on $1.0\times1.0\times0.15-mm$ microparts was less than $2{\mu}m$ in the X and Y directions and 0.2 degrees in the e direction. These alignment errors were almost the same as those obtained using water. The use of a suitable adhesive had no negative effects on the alignment accuracy. The average tensile strength of the adhesive bond after self-alignment was $0.61N/mm^2$.

• 한국가시화정보학회지
• /
• 제19권3호
• /
• pp.123-129
• /
• 2021

Many plants and animals in nature have superhydrophobic surfaces. This superhydrophobic surface has various properties such as self-cleaning, moisture collection, and anti-icing. In this study, the superhydrophobic properties of PTFE surface were treated by plasma etching. There were four important factors that changed the surface properties. Micro-sized protrusions were formed by plasma etching. The most influential parameter was RF Power. The contact angle of the pristine PTFE surface was about 113.8°. The maximum contact angle of the surface after plasma treatment with optimized parameters was about 168.1°. In this case, the sliding angle was quite small about 1°. These properties made it possible to remove droplets easily from the surface. To verify the self-cleaning effect of the surface, graphite was used to contaminate the surface and remove it with water droplets. Graphite particles were easily removed from the optimized surface compared to the pristine surface. As a result, a surface having water repellency and self-cleaning effects could be produced with optimized plasma etching parameters.

• 한국분무공학회지
• /
• 제5권1호
• /
• pp.5-12
• /
• 2000

The beneficial aspects of applying emulsion fuels to combustion systems may be due to the changes of fuel properties which lead to the enhanced atomization characteristics. The spray characteristics of water/oil emulsified fuel injected from the pressure-swirl(simplex) atomizer using for oil burner were investigated. Four different water contents from 10 to 40 % by volume at 10% increment were prepared by mixing with the different contents of surfactants. Total amount of surfactant used was varied from 1 to 3 % by volume. This study demonstrates the influence of water and surfactant contents of emulsified fuel, injection pressure on the spray characteristics, i.e. Sauter mean diameter(SMD) and spray angle. The drop size distribution of the emulsified fuel spray was measured with a Malvem particle sizer. In order to measure the spray angle, the digital image processing was employed by capturing multiple images of the spray with 3-CCD digital video camera. It was evident that the addition of water and surfactant changes fuel properties which are the key parameters influencing the atomization of the spray. The increase in surfactant content results in the decrease of SMD and the increase in spray angle. The droplets decease with increase in injection pressure, but the influence of injection pressure in this experimental condition was less important than expected. The more viscous fuel with the increase of water content exhibits the larger droplets in the centerline of the spray, and the less viscous fuel in the outer edges of the spray. The increase in axial position from the nozzle causes the spray angle to decrease. The spray angle decreases with increase in water content. This is due to increase in viscosity with increase in water content.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2015년도 추계학술대회 논문집
• /
• pp.199-200
• /
• 2015

실리콘 기판위에 Gecko의 피부를 모사한 다층의 나노, 마이크로 구조표면에서 일어나는 응결된 water vapor droplets의 coalescence에 기인하는 surface energy의 kinetic energy의 변환을 통하여 발생하는 water droplets의 self-propelling을 이용한 빙점하에서 dynamic wetting 성질의 관찰을 통해서 얼음 방지, 지연, 또는 얼음 부착성 최소화 표면의 구현 가능성을 보여준다.

• 대한기계학회논문집B
• /
• 제20권2호
• /
• pp.624-631
• /
• 1996

가솔린 화재의 소화과정을 규명하기 위하여 부력과 순수확산에 의해서만 연료와 산화제가 혼합되는 순수확산화염을 대항으로 수분무에 의한 소화실험을 체계적으로 수행하여 다음과 같은 결론을 얻었다. 1) 수분무는 특정 조건에서 수분무가 없을 때인 자연연소상태에 비하여 더 높은 값의 연소율을 가지게 되어, 오히려 화재의 연소를 촉진하게 된다. 2) 수분무시 연소율은 자연연소상태보다 더 높은 값으로 증가하다가 어느 순간 연료표면의 냉각조건이 충분히 이루어지면 소화기 일어나게 된다. 30 수분무에 의해 유입되는 공기는 분무 자체와 함쎄 화염을 반경방향으로 흐트러지게 함으로써 연료와 공기와의 접촉면적을 증대시켜 연소를 촉진하는 반면, 분무수가 연료 표면에 쉽게 도달할 수 있도록하여 연료표면을 보다 잘 냉각시키게 된다. 즉 주위공기의 유입은 연소율의 증가 및 감소에 영향을 미친다. 4) 본 실험조건에서는 분무수의 입경이 약 40.mu.m 이하인 액적들은 화염구역내에서 증발하거나 그 경로가 바뀌어 연료 표면에 도달되지 못함을 발견하였다. 5) 본 연구와 같이 주로 냉각작용에 의하여 화염이 소화되는 경우에는, 화염자체의 냉각효과 보다는 연료표면의 냉각에 의한 효과가 지배적임을 알 수 있었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.738-744
• /
• 2000

The breakup behaviors of impinging droplet on a hot surface are studied experimentally. The droplets are produced by the dripping method and the breakup behaviors of liquid droplet are recorded by photographs. Experimental conditions are, droplet diameter di : 2.5, 3.2 [mm], weber number : $30{\sim}140$, surface temperature : $28^{\circ}C(room\;temperature){\sim}450^{\circ}C$. Water is used to liquid. As weber number of droplet increases, a liquid sheet, which is formed after the impingement on a hot surface, is disintergrated by the dynamical effect. But at low weber number, it has effected by thermodynamical effect. The breakup behaviors of droplet are divided into three patterns with weber number and surface temperature, non-disintegration, transition and disintegration region. Further, these boundary values are affected by the hot surface temperature and weber number. SMD of breakup droplets are calculated in according to surface temperatures and weber number. The minium SMD of breakup droplets are observed at weber number 65.49, temperature $250^{\circ}C$ and weber number 99.08, temperature $350^{\circ}C$.

• Korean Chemical Engineering Research
• /
• 제51권6호
• /
• pp.760-765
• /
• 2013

액적기반 미세유체 시스템을 이용해 난백단백질인 라이소자임의 결정화실험을 하였다. Flow-focusing 칩을 이용해 water-in-oil 형태의 액적을 만들고 페트리 디쉬와 십자몰드에 넣은 후, 액적 내부에서 라이소자임 수용액과 침전제 (NaCl) 사이의 액-액 반응을 관찰하였다. 그리고 수용액의 pH가 4.8일 때와 7.2일 때의 결정형태를 비교하였다. 그 결과, pH 4.8에서는 다면체 또는 판상형의 결정이 형성되었고, pH 7.2에서는 침상형 결정이 생성되었다. pH 4.8, 7.2 두 경우 액적이 홀로 있을 때에는 액적부피가 유지되거나 감소하면서 결정이 형성되었다. 하지만 액적이 서로 인접해 있을 때는 액적사이의 상호작용이 관찰되었고, 두 pH에서 다른 경향성을 보였다. pH 4.8에서는 인접한 액적의 부피에 영향을 주어 한 액적의 부피가 커졌고, 부피가 커진 액적에서 결정이 형성되었다. pH 7.2에서는 부피에 영향을 서로 주지 않고 각각의 액적에서 결정이 형성되었다.

• Nuclear Engineering and Technology
• /
• 제23권2호
• /
• pp.183-199
• /
• 1991

가압수형 원자로 가압기의 오동작 보조살수 과도시 용기벽에서의 온도분포에 대한 과도응답을 해석하였으며, 해석은 분무수적으로 젖게되는 용기벽면에서 나타나는 열응력에 대하여 보수적으로 수행되었다. 수적이 부딪혀서 흘러내리는 용기벽의 내부경계면에서 강제대류열전달계수를 결정하기 위하여, 분무수적들이 살수노즐을 떠나 수증기와 비응축성인 수소기체로 이루어진 혼합기로 채워져 있는 가압기 내부공간을 통하여 비행한 후에 용기내부벽면에 도달할 때의 수적들의 과도온도를 예측하였다. 용기벽에서의 과도온도분포는 유한요소법을 사용하여 구하였으며, 대표적인 결과들을 제시하였다. 열해석의 결과는 입력자료에 대한 묘사와 부합되며, 타당한 물리적 의미를 가짐 이 확인되었다.