• Environmental and Resource Economics Review
• /
• v.14 no.2
• /
• pp.419-445
• /
• 2005

In 2002, the waste was generated about 277,533tons per day. The treatments of waste were recycling, which had accounted for almost 70%, landfill, which had accounted for 19.8%, and incineration, which had accounted for 6.5%. The energy recovery from incineration has been increased since 1995. The portion of waste in the renewable energy has been increased. Waste incineration heating system generates total 134TOE of $CO_2$ as compared to 6,800TOE of GHG from LNG boiler centralized heating system to bring 98% reduction rate of GHG emissions. We need the integrated model to examine the impacts of waste managements on economy and environments. The Asia-Pacific Integrated Model is introduced as the example of the integrated model.

• Journal of environmental and Sanitary engineering
• /
• v.23 no.3
• /
• pp.1-8
• /
• 2008

Currently, medical waste stoker incinerator is widely used in the emission control technology of health-care risk waste and miscellaneous contaminated waste. In the past, wet type control technology was used to remove the major harmful gaseous contaminants of medical waste such as HCl, $NO_x,\;SO_2$, CO, DUST, Dioxin. However, the treatment cost for wastewater was high and it has a disadvantage for frozen system during winter season. Therefore, in order to obtain effective treatment, the dry type control technology was developed and widely used to remove the gaseous contaminants. In this study, pre-coated bag filter using hydrated lime, ($Ca(OH)_2$), was applied to the dry type control system and the optimum dose of hydrated lime was investigated. The treatment results showed that the dust collection rate was approximately 26.7%. Moreover, the HCl removal rate using pre-coated bag filter ($50mg/sm^3\;Ca(OH)_2$) was 13.52%, which was significantly higher than 3.26% obtained from conventional bag filter.

• New & Renewable Energy
• /
• v.19 no.3
• /
• pp.22-33
• /
• 2023

The number of fire and explosion accidents caused by pyrolysis oil and gas at waste plastic pyrolysis plants is increasing, but accident status and safety conditions have not been clearly identified. Therefore, the aim of the study was to identify the risks of the waste plastic pyrolysis process and suggest appropriate safety management measures. We collected information on 19 cases of fire and explosion accidents that occurred between 2010 and 2021 at 26 waste plastic pyrolysis plants using the Korea Occupational Safety and Health Agency (KOSHA) database and media reports. The mechanical, managerial, personnel-related, and environmental problems within a plant and problems related to government agencies and the design, manufacturing, and installation companies involved with pyrolysis equipment were analyzed using the 4Ms of Machines, Management, Man, and Media, as well as the System-Theoretic Accident Model and Processes (STAMP) methodology for seven accident cases with accident investigation reports. Study findings indicate the need for establishing legal and institutional support measures for waste plastic pyrolysis plants in order to prevent fire and explosion accidents in the pyrolysis process. In addition, ensuring safety from the design and manufacturing stages of facilities is essential, as are measures that ensure systematic operations after the installation of safety devices.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2004.02a
• /
• pp.28-41
• /
• 2004

The study is aimed to assess the usefulness of the mixture design for spent resin immobilization in cement. Although a considerable amount of research has been carried out to determine the limits for the composition of an acceptable resin-cement mixture, no efficient experimental strategy exists that explores the full properties of waste form against composition relationship. In order to gain an overall view, this report introduces the method of mixture design and mixture analysis, and describes the design of experiment of the 5-component mixture with the constraint conditions. The mathematic models of 28-day compressive strength varying with the ingredients are fitted, and the main effect and interaction effect of two ingredients are identified quantitatively along with the graphical interpretation using the response trace plot and contour plots.

• Nuclear Engineering and Technology
• /
• v.54 no.10
• /
• pp.3957-3961
• /
• 2022

Deposition behaviors of Sr and Cs in various liquid cathodes, such as Zn, Bi, Cd, and Pb, were examined to evaluate their recovery from LiCl-KCl eutectic salt. Cations in the salt were deposited on the liquid cathode, exhibiting potential of -1.8 to -2.1 V (vs. Ag/AgCl). Zn cathode had successful deposition of Sr and exhibited the highest recovery efficiency, up to 55%. Meanwhile, the other liquid cathodes showed low current efficiencies, below 18%, indicating LiCl-KCl salt decomposition. Sr was recovered from the Zn cathode as irregular rectangular SrZn₁₃ particles. A negligible amount of Cs was deposited on the entire liquid cathode, indicating that Cs was hardly deposited on liquid cathodes. Based on these results, we propose that liquid Zn cathode can be used for cleaning Sr in LiCl-KCl salt.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.16 no.2
• /
• pp.183-193
• /
• 2018

Currently, the Korea Atomic Energy Research Institute (KAERI) is planning to build the Ki-Jang Research Reactor (KJRR) in Ki-Jang, Busan. It is important to safely dispose of low-level radioactive waste from the operation of the reactor. The most efficient way to treat radioactive waste is cement solidification. For a radioactive waste disposal facility, cement solidification is performed based on specific waste acceptance criteria such as compressive strength, free-standing water, immersion and leaching tests. Above all, the leaching test is important to final disposal. The leakage of radioactive waste such as $^{137}Cs$ causes not only regional problems but also serious global ones. The cement solidification method is simple, and cheaper than other solidification methods, but has a lower leaching resistance. Thus, this study was focused on the development of cement solidification for an enhancement of cesium leaching resistance. We used Zeolite and Loess to improve the cesium leaching resistance of KJRR cement solidification containing simulated KJRR liquid waste. Based on an SEM-EDS spectrum analysis, we confirmed that Zeolite and Loess successfully isolated KJRR cement solidification. A leaching test was carried out according to the ANS 16.1 test method. The ANS 16.1 test is performed to analyze cesium ion concentration in leachate of KJRR cement for 90 days. Thus, a leaching test was carried out using simulated KJRR liquid waste containing $3000mg{\cdot}L^{-1}$ of cesium for 90 days. KJRR cement solidification with Zeolite and Loess led to cesium leaching resistance values that were 27.90% and 21.08% higher than the control values. In addition, in several tests such as free-standing water, compressive strength, immersion, and leaching tests, all KJRR cement solidification met the waste acceptance or satisfied the waste acceptance criteria for final disposal.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2007.11a
• /
• pp.327-328
• /
• 2007

The deposition conditions for plating polonium have been optimized with deposition parameters such as pH, volume and temperature of the deposition and deposition time. In the tap water, the chemical yields of polonium forthe deposition solution adjusted to pH 0 were higher than those for the deposition solution adjusted to pH 2. This modified auto-deposition method made it possible to obtain reliable data of activity concentration of Po-210.

• Clean Technology
• /
• v.25 no.4
• /
• pp.289-295
• /
• 2019

Though the usage of vinyls and plastics produced from fossil fuels has been increasing in the world, the eco-friendly domestic disposal or recycling of waste vinyls has to be executed because the migration or importation of waste vinyls or waste plastics are globally prohibited. Even though the eco-friendly domestic disposal or recycling of waste vinyls and waste plastics should be developed, promising eco-friendly recycling methods are few because there are extraneous substances in waste vinyls and waste plastics. Also, conventional incineration and landfill methods result in secondary contamination and then increase disposal costs. Therefore, the selective elimination of extraneous substances or other materials included in waste vinyls and waste plastics could make valuable recycling or reuse possible. In particular, the novel hybrid process in which crushing and screening are simultaneously conducted in a rotary kiln type reactor can domestically maximize the material recycling or reuse. In this study, the feasibility study for a crushing/screening hybrid process developed in Korea was performed and evaluated in case of thermal recycling (TR) and material recycling (MR). The effect of various subsidies on economic efficiency was especially evaluated by means of domestic recycling plans. The incentive revenues from waste vinyl recycling and the incineration share of waste vinyls affected the net present values and internal rate of returns of the hybrid process.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2012.10a
• /
• pp.131-132
• /
• 2012

The vacuum plasma coating was performed to analysis the characteristic and find the optimum process conditions for the vacuum plasma spray coating. It was observed that the square shape of powder in case of carbide ceramics does not fluidize well compared to the round shape of powder in case of oxide ceramics so that the plasma spraying is not uniform. The analysis through SEM and EDS mapping shows that the coatings represent excellent structural features with strong resistance against oxidation and satisfied result with vacuum plasma coating.

• New & Renewable Energy
• /
• v.10 no.4
• /
• pp.29-35
• /
• 2014

Non-used waste heat has recently been paid special attention due to several global warming regulation and energy cost rising. In this study, therefore, thermal energy storage system which uses a solid type heat media has been investigated about the possibility of heat accumulation and heat release for thermal energy storage system. 35kWh of bench-scale thermal storage system was used to investigate the characteristics of the solid type heat media. From the result, it is shown that a solid type heat media should be divided to supply constant heat to the customers' side. It is also shown the flow direction should be considered to reduce temperature difference between top and bottom sides in the thermal storage system.