• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.1
• /
• pp.179-185
• /
• 2000

In this study, we examined the movement of chlorophenol as a precursor of the dioxin in the after-combustion to minimize the creation and emission of dioxin in a municipal waste incinerator. The CPs was injected to the electric incinerator in temperature $300{\sim}500^{\circ}C$, using $N_2$ gas to control the reaction time, The oxygen quantity supplied into the $CP_s's$ isomer combustion was added with the value of experience formula. When the space velocity in reactor was 60~80/sec, the removal efficiency of CP was obtained in the presence of Mo-V catalyst and non catalyst. The efficiency in non-catalyst was 74% to 80% mono-CP, di-CP 55~66%, tri-CP 50~58%, while mono-CP 90~99.9%, di-CP 96~97%, tri-CP 76~99% in a catalyst. Consequently, it was shown that these were 20~30% more efficienct than those.

• Transactions of the Korean hydrogen and new energy society
• /
• v.23 no.1
• /
• pp.8-18
• /
• 2012

This paper presents a three-dimensional, transient cold-start polymer electrolyte fuel cell (PEFC) model to numerically evaluate the effects of membrane electrode assembly (MEA) design and cell location in a PEFC stack on PEFC cold start behaviors. The cold-start simulations show that the end cell experiences significant heat loss to the sub-freezing ambient and thus finally cold-start failure due to considerable ice filling in the cathode catalyst layer. On the other hand, the middle cells in the stack successfully start from $-30^{\circ}C$ sub-freezing temperature due to rapid cell temperature rise owing to the efficient use of waste heat generated during the cold-start. In addition, the simulation results clearly indicate that the cathode catalyst layer (CL) composition and thickness have an substantial influence on PEFC cold-start behaviors while membrane thickness has limited effect mainly due to inefficient water absorption and transport capability at subzero temperatures.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.321-324
• /
• 2009

Upgrading of pyrolysis wax oil has been conducted in a continuous fixed bed reactor at $450^{\circ}C$, 1hour, LHSV 3.5/h. The catalytic degradation using HZSM-5 catalyst are compared with the thermal degradation and also was studied with a function of experimental variables. The raw pyrolysis wax oil shows relatively high boiling point distribution ranging from around $300^{\circ}C$ to $550^{\circ}C$, which has considerably higher boiling point distribution than that of commercial diesel. The product characteristic from thermal degradation shows a similar trend with that of raw pyrolysis wax oil. This means the thermal degradation of pyrolysis wax oil at high degradation temperature is not sufficiently occurred. On the other hand, the catalytic degradation using HZSM-5 catalyst relative to the thermal degradation shows the high conversion of pyrolysis wax oil to light hydrocarbons. This liquid product shows high gasoline range fraction as around 90% fraction and considerably high aromatic fraction in liquid product. Also, in the catalytic degradation the experimental variable such as catalyst amount and reaction temperature was studied.

• Journal of the Korean Wood Science and Technology
• /
• v.14 no.3
• /
• pp.43-46
• /
• 1986

A stainless steel autoclave reactor, which is the property of Pacific Northwest Laboratories(PNL) and located in PNL, was acted for pyrolysis and gasification of sawdust, ricestraw, and ricehusk. The initial reaction temperature of this reactor was 300$^{\circ}C$, and up to 500$^{\circ}C$ to complete pyrolysis and gasification reaction. The maximum exerted pressure on this reactor was 800 psig. In order to examine the effect of catalyst on reaction temperature, $K_2CO_3$, and nickel/alkali carbonate catalyst mixture were also used. The experimental results obtained with this reactor indicated that good yields of methane-rich gas(exceeding 40% methane) can be produced. The product gas mixtures were also identified to be CO. $CO_2$, $C_2H_4$, and $CH_3CHO$ etc. by Gas Chromatography and Mass Spectrometer.

• Journal of the Korean Wood Science and Technology
• /
• v.19 no.4
• /
• pp.80-84
• /
• 1991

Lignocellulosic biomass including acetosolv ricestraw and spruce lignin were liquefied and converted into liquid hydrocarbons by catalytic hydroliquefaction reaction. These experimental works were carried out in 1-liter-capacity autoclave using 50% tetralin and m-cresol solution respectively as soluble solvent and Ni. Pd. Fe and red mud as catalyst. $H_2$ gas was supplied into the reactor for escaltion of deoxhydroenolysis reaction. Catalyst concentrations were 1 % of raw material based on weight. The ratio between raw materials and soluble solvent are 1g and 10cc. The reaction conditions are 400-$700^{\circ}C$ of reaction temperature, 10-50 atms of reaction pressure. The highest yield of hydrocarbon, so called "product oil" showed 32% and 5.5% of lowest char formation when red mud was used as catalyst. The product oil yields from those of other catalysts were in the range of 20-29%. The influence of different initial hydrogen pressures was examined in the range d 30-50 atms. A minimum pressure of 35 atms was necessary to obtain a complete recovery of souble solvent for recycling.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.3
• /
• pp.715-720
• /
• 2014

A Cu(II) complex with an three nitrogens and one sulfur coordination environment was synthesized and characterized. Its redox potential was observed at 0.483 V vs. NHE, very similar to that of a Cu-containing fungal enzyme, galactose oxidase, which catalyzes the oxidation of alcohols to corresponding aldehydes with the concomitant reduction of molecular oxygen to water. The Cu(II) complex selectively oxidizes the benzylic alcohols using TEMPO/$O_2$ under mild reaction conditions to corresponding aldehydes without forming any over-oxidation product. Moreover, the catalyst can be recovered and reused multiple times for further oxidation reactions, thus minimizing the waste generation.

• Transactions of the Korean hydrogen and new energy society
• /
• v.6 no.1
• /
• pp.11-16
• /
• 1995

Chemical heat pump is one of the energy conversion technologies, which enables to use waste heat as a source of high grade heat. In 2-propanol/acetone system, the dehydrogenation of 2-propanol is an endothermic(heat absorption) reaction, and can be used to generate hydrogen because 2-propanol can be converted to acetone and hydrogen at low temperature(about $8^{\circ}C$) using catalyst. For the dehydrogenation of 2-propanol 5% Ru catalyst based on activated carbon is the best one at the reaction temparature of $83^{\circ}C$.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.2
• /
• pp.213-217
• /
• 2008

The objective of this research is to investigate the leaching characteristics of unregulated heavy metals such as Ni, Zn, Ba, Be, Sb, Se, V in specified waste. 108 waste samples which were taken from the representative facilities emitting hazardous substances, were analyzed. The rate of leaching of heavy metal was measured using an official test method. From the results, wastewater treatment sludge and dust contained much Ni, and Zn was detected in all samples. Dust and waste catalyst producted from petroleum-refining process tended to reveal V in high concentration. Ba, Be, Sb, Se showed low concentration, but require additional analyses of waste generated at different industries.

• KSBB Journal
• /
• v.27 no.1
• /
• pp.51-56
• /
• 2012

This research was to investigate the polyester preparation using waste ethylene glycol (EG) generated from the wastepaper pretreatment process. Waste EG was obtained from using EG five times repeatedly in the pretreatment of wastepaper. The hydroxyl value of the waste EG was 441 mg KOH/g and its composition was 0.68% cellulose, 6.5% hemicellulose, 6.1% lignin, and 86.7% EG. Maleic acid was used as carboxylic acid. The effect of reaction temperature and time except carboxyl group/hydroxyl group ratio on the crosslinkage of the prepared polyester was marginal. Citric acid, lithium hydroxide and dicumyl peroxide were used as additive or catalyst to enhance the crosslinkage of polyester. Among them, 10% of citric acid was found to be most effective. The crosslinkage was 86% when the polyester was prepared at an optimum condition such as $130^{\circ}C$ and 15 minutes, 1.5 of C/H ratio, and 10% of citric acid, and its insoluble percentage in boiling water for 6 hours was 47%. The weight loss of the prepared polyester was approximately 40% when it was buried in damp soil for 5 months, indicating that it is readily biodegradable. This results can provide some information for future development of wastepaper pretreatment by organic solvent.

• Applied Chemistry for Engineering
• /
• v.19 no.5
• /
• pp.466-470
• /
• 2008

The objective of this study is to convert methane into hydrogen using a nanoporous catalyst in the $CO_2$ containing syngas generated from the gasified waste. For the purpose, $Ni/Al_2O_3$ catalyst was prepared with the one-pot method. According to analyses of the catalyst, three dimensionally linked sponge shaped particles were created and the prepared nanoporous catalysts had larger surface area and smaller particle size and more uniform pores compared to the sphere shaped commercial catalyst. The catalyst for reforming reaction gave the highest $CH_4$ conversion of 91%, and $CO_2$ conversion of 92% when impregnated with 16 wt% of Ni at the reaction temperature of $750^{\circ}C$. At that time, the prepared catalyst remarkably improved the $CH_4$ and $CO_2$ conversion up to 20% compared to the commercial one.