• Environmental Engineering Research
• /
• 제23권4호
• /
• pp.456-461
• /
• 2018

The solid-state anaerobic digestion (SS-AD) has promoted the development and application for biogas production from biomass which operate a high solid content feedstock, as higher than 15% of total solids. However, the digested byproduct of SS-AD can be used as a fertilizer or as solid fuel, but it has serious problems: high moisture content and poor dewaterability. The organic residue from SS-AD has to be improved to address these problems and to make it a useful alternative energy source. Hydrothermal carbonization was investigated for conversion of the organic residue from the SS-AD of livestock waste to solid fuels. The effects of hydrothermal carbonization were evaluated by varying the reaction temperatures within the range of $180-240^{\circ}C$. Hydrothermal carbonization increased the calorific value through the reduction of the hydrogen and oxygen contents of the solid fuel, in addition to its drying performance. Therefore, after the hydrothermal carbonization, the H/C and O/C atomic ratios decreased through the chemical conversion. Thermogravimatric analysis provided the changed combustion characteristics due to the improvement of the fuel properties. As a result, the hydrothermal carbonization process can be said to be an advantageous technology in terms of improving the properties of organic waste as a solid-recovered fuel product.

• 한국응용과학기술학회지
• /
• 제27권4호
• /
• pp.437-444
• /
• 2010

Dry Process(natural drying, hot-air drying, oil fry drying), optimized mixture ratio and the condition of carbonization was carried out in order to improve the product durability develop eco-friendly solid fuel mixing food waste and paper sludge. As a result of the experiment, oil fry drying process was the fastest method for drying food waste and paper sludge mixture that contains 80% water inside, and the optimized mixture ratio to minimize the generating concentration of chlorine gas against caloric value of mixture ratio was 7:3. Additionally proper temperature of product carbonization was about $200^{\circ}C$ and shown increasing product durability through the carbonization. Therefore, the pelletized solid fuel be shaped diameter around 0.5cm, length 2cm under which was pulverized and molded using 7:3 mixture of food waste, and paper sludge was the eco-friendly solid fuel possible to be industrialized which is consist of chlorine concentration of below 2.0wt% and the lowest caloric value of over 5,000kcal/kg. In conclusion, this developing manufacturing process of the solid fuel can be interpreted to contribute alternative energy development in accordance with low carbon and green growth era.

• Journal of Biosystems Engineering
• /
• 제32권5호
• /
• pp.316-323
• /
• 2007

This study was carried out to obtain the basic data for the development of the solid fuel with investigating the characteristics of mixtures of animal wastes and wasted coal and supply it as an energy resource to agricultural farms for heating of agricultural facilities. It was investigated for the characteristics of animal wastes (swine waste, swine waste with sawdust, cattle waste), wasted coal, the mixtures of animal wastes and wasted coal with or without mixing seawater. The characteristics of solid fuel according to the mixture ratio of animal wastes and wasted coal were analyzed. The effects of seawater affecting on calorific value and thermal pyrolysis of solid fuels were investigated. The results of this study are as follows: 1) The calorific value was improved with mixing seawater into wasted coal due to chemical reaction. 2) The diverse solid fuels of various calorific values can be made with adjusting the ratio of animal wastes and wasted coal. 3) Animal wastes and wasted coal had each different reaction temperature of thermal pyrolysis and the decreasing rate of weight. 4) The mixture of animal wastes and wasted coal would be ignited easily. Therefore, the solid fuel could be ignited more conveniently when seawater is mixed with it.

• Environmental Engineering Research
• /
• 제24권4호
• /
• pp.529-542
• /
• 2019

Nowadays, drying methods for municipal solid waste quality improvement have been adopted in the developed and developing countries to valorize wastes for a renewable energy source, reduce dependency on fossil fuel and keep safer disposal at landfills. Among them, biodrying, biostabilization, thermal drying and solar drying are the most common. Drying of municipal solid waste could offer several environmental and economic benefits. Therefore, this review highlighted the drying methods for municipal solid waste quality improvement around the world and compared them based on the reduction of moisture, weight and volume of municipal solid wastes against drying temperature and time by using statistical analysis. It was observed that the drying temperature of different drying methods accounted for 115 ± 40℃ for thermal drying, 59 ± 37℃ for solar drying, 55 ± 15℃ for biodrying and 58 ± 11℃ for biostabilization. Among the drying methods, thermal drying provided the shortest drying time. The moisture reduction, weight reduction, volume reduction and heating value increase of municipal solid waste could vary with drying temperature and time. Finally, the benefits and drawbacks of different drying methods were specified, and recommendations were made for the future efficient drying.

• 유통과학연구
• /
• 제18권9호
• /
• pp.67-75
• /
• 2020

Purpose: The purpose of this study is to enhance sales promotion efficiency for using solid refuse fuel facilities. Renewable energy technology using Solid Refuse Fuel (SRF) is an economic efficiency technology that recovers waste by burning various wastes. A survey on the pollutants discharged from the solid fuels facilities was investigated so that the SRF facilities could be expanded, distributed and reflected in the policy. Research design, data, and methodology: In this study, 9 business sites using SRF and Bio-SRF as main raw materials were investigated for 2 years. The characteristics of target business sites such as the type of fuel used, combustion method, combustion temperature, daily fuel consumption and environmental prevention facilities were studied. Results: The average pollution & ammonia concentration of Bio-SRF facilities was found to be 88.15% higher than that of SRF facilities. But the average acetaldehyde concentration of SRF facilities was found to be 88.15% higher than that of Bio-SRF facilities. Conclusions: The main issue is how much electric power generation using combustible materials affects air pollution. The waste recycling law provides the standard value according to the fuel property, but there is a considerable gap with the mixed fuel. Therefore, for efficient utilization of facilities using solid fuel products, additional research is needed to improve the distribution structure of exhaust pollutants is needed.

• 한국건설순환자원학회논문집
• /
• 제5권2호
• /
• pp.116-123
• /
• 2010

현행 "건설폐기물의 재활용 촉진에 관한 법률" 시행규칙에서는 가연성 건설폐기물의 재활용에 대한 명확한 규정 없이 배출규정만을 제안하여 대부분의 가연성폐기물이 단순 소각 또는 혼합폐기물의 형태로 소각 또는 매립되고 있는 실정이다. 따라서 가연성 건설폐기물의 단순 소각을 최대한 억제하여 연료화 등으로 재활용 할 수 있는 제도적 방안의 마련이 필요한다. 본 연구에서는 이를 위하여 가연성 건설폐기물의 발생 및 처리현황을 분석 조사하였고 국내 폐기물 고형연료관련 제도 및 법규를 검토하였다. 그리고 이를 토대로 국내 가연성 건설폐기물의 연료화를 위한 문제점을 분석하여 가연성 건설폐기물을 활용한 고형연료의 정착을 위한 정책적 방안을 제시하였다.

• 유기물자원화
• /
• 제21권2호
• /
• pp.51-55
• /
• 2013

본 연구에서는 축산폐기물과 농업부산물을 이용한 펠릿연료의 성분 분석과 연소 특성에 대한 연구를 수행하였다. 축산폐기물을 이용한 고형 연료 특성 분석 결과 삼성분, 원소분석 및 발열량 등에 있어 고형연료화 기준에 적합한 것으로 나타났다. 또한 회분의 경우 다량의 K, P, Na 등이 함유되어있어 토양개량제로 사용이 가능할 것으로 기대된다. 그러나 축분만을 이용할 경우 낮은 발열량으로 인하여 연료로서의 적합하지 않을 것으로 판단된다. 이를 위해 농가의 수분조절용으로 사용되는 왕겨 및 톱밥과 같은 고발열물질의 혼합 성형하여 발열량과 초기점화성을 높일 경우 충분히 연료로써의 활용가치가 높을 것으로 기대된다.

• 한국수소및신에너지학회논문집
• /
• 제30권4호
• /
• pp.303-311
• /
• 2019

Reversible solid oxide fuel cell (RSOFC) has become a prospective device for energy storage and hydrogen production. Many studies have been conducted around the world focusing on system efficiency improvement and realization. The system should have not only high efficiency but also a certain level of simplicity for stable operation. External waste steam utilization was proved to remarkably increase the efficiency at solid oxide electrolysis system. In this study, RSOFC system coupled with waste steam was proposed and optimized in term of simplicity and efficiency. Ejector for fuel recirculation is selected due to its simple design and high stability. Three system configurations using ejector for fuel recirculation were investigated for performance of design condition. In parametric study, the system efficiencies at different current density were analyzed. The system configurations were simulated using validated lumped model in EBSILON(R) program. The system components, balance of plants, were designed to work in both electrolysis and fuel cell modes, and their off-design characteristics were taken into account. The base case calculation shows that, the system with suction pump results in slightly lower efficiency but stack can be operated more stable with same inlet pressure of fuel and air electrode.

• 대한기계학회논문집B
• /
• 제23권2호
• /
• pp.159-165
• /
• 1999

Experimental studies have been performed to observe the basic phenomena of waste bed combustion in MSW incinerator. A reduced scale apparatus was utilized to simulate the combustion behavior in real plant with 1-dimensional transient behavior at the experimental setup, which uses wet cubic wood with ash content as simulated waste. LHV (lower heating value) of solid fuel, fuel particle size and flow rate of combustion air were taken as important parameters of the bed combustion. For the quantitative analysis, FPR (flame propagation rate), TBT (total burn-out time) and PBT (particle burn-out time) was defined. LHV represent the capability of heat release of the fuel, so that a higher LHV results in faster reaction rate of the fuel bed, which is shown by higher FPR. Fuel particle size is related with surface area per unit mass as well as heat and mass transfer coefficient. As the particle size increases the FPR decreases owing to decreasing specific surface area. Air injection supplies oxygen to the reaction zone. However oversupply of combustion air increases convection cooling of the bed and possibly extinguishes the flame.

• 방사성폐기물학회지
• /
• 제20권3호
• /
• pp.365-369
• /
• 2022

Operating and decommissioning nuclear power plants generates radioactive waste. This radioactive waste can be categorized into several different levels, for example, low, intermediate, and high, according to the regulations. Currently, low and intermediate-level waste are stored in conventional 200-liter drums to be disposed. However, in Korea, the disposal of intermediate-level radioactive waste is virtually impossible as there are no available facilities. Furthermore, large-sized intermediate-level radioactive waste, such as reactor internals from decommissioning, need to be segmented into smaller sizes so they can be adequately stored in the conventional drums. This segmentation process requires additional costs and also produces secondary waste. Therefore, this paper suggests repurposing the no-longer-used spent nuclear fuel casks. The casks are larger in size than the conventional drums, thus requiring less segmentation of waste. Furthermore, the safety requirements of the spent nuclear fuel casks are severer than those of the drums. Hence, repurposed spent nuclear fuel casks could better address potential risks such as dropping, submerging, or a fire. In addition, the spent nuclear fuel casks need to be disposed in compliance with the regulations for low level radioactive waste. This cost may be avoided by repurposing the casks.