• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.6
• /
• pp.287-293
• /
• 2014

Internal combustion engines release 30~40% of the energy from fossil fuels into the atmosphere in the form of exhaust gases. By utilizing this waste heat, plenty of energy can be conserved in the auto industry. Thermoelectric generation is one way of transforming the energy from engine's exhaust gases into electricity in a vehicle. The thermoelectric generators located on the exhaust pipe have been developed for vehicle applications. Different experiments with thermoelectric generators have been conducted under various test conditions as following examples: hot gas temperature, hot gas mass flow rate, coolant temperature, and coolant mass flow rate. The experimental results have shown that the generated electrical power increases significantly with the temperature difference between the hot and the cold side of the thermoelectric generator and the gas flow rate of the hot-side heat exchanger. In addition, the gas temperature of the hot-side heat exchanger decreases with the length of the thermoelectric generator, especially at a low gas flow rate.

• Journal of Environmental Health Sciences
• /
• v.29 no.4
• /
• pp.35-41
• /
• 2003

The objective of this study was investigate the generation rates, composition, proportion and calorific values each of material in the municipal solid wastes as well as the effect of incineration residual leachate on the environment in Yangsan sanitary landfill site. The results were as follows ; The annual average generation rate of municipal solid wastes in Yang-san is approximately 2.0 kg/cㆍd. The weight percent of combustible matters is on average 78∼87% and the lower heating values of municipal solid wastes is measured to be more than 2,151 kcal/kg after removing the briquette component. The food waste was major source of solid wastes in Yang-san city as 35% and its variation by seasons was negligible. Combustible part was larger than incombustible part of the domestic solid wastes in spring and summer. It is recommended that municipal solid wastes be treated by multiple methods such as the sanitary landfill, resources and recovery, composting and incineration.

• Applied Chemistry for Engineering
• /
• v.3 no.2
• /
• pp.207-212
• /
• 1992

Main disposal technology for industrial wasites in Korea has been landfilling, however, this is encountering serious problems such as the lack of landfill sites and objections of residents. Incineration, therefore, has become a final solution for this dilema. Various kinds of air pollutants generation are possible because of the variety of types and compositions of wastes generated in industry. In this paper, air pollutants produced while incinerating hazardous industrial wastes are discussed and some control technologies are surveryed with the purpose of optimal design of incinerators and emission reduction. From this initial stage of incinerator utilization, low-emission type should be developed and applied and intensive research on pollutant generation due to waste incineration and advanced control technologies should be also performed.

• Journal of Ocean Engineering and Technology
• /
• v.14 no.4
• /
• pp.62-97
• /
• 2000

Recently the research for utilization of waste heat produced from electric power plants, casting factories, heat treating factories or commercial are being afforded by the need for energy saving. The objective of this study is to develop a thermoelectric generation system which unused energy from close-at-hand sources such as garbage incineration heat and industrial exhaust etc. into electricity. This paper a thermoelectric technology on a optimum system design method and efficiency and cost effective thermoelectric element on order to extract the maximum power output from energy conversion of waste energy. It is shown that the longitudinal stresses of module contacted with two point constrained Al tubes could be released more than those with a one-point constrained.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.11a
• /
• pp.165-166
• /
• 2018

Researches for the development of renewable energy as a fuel substitute for global warming and depletion of petroleum resources are actively being carried out. Among them, the annual growth rate of PV generation is 20.73%, which is higher than other renewable energy sources. However, the production of 1 ton of polysilicon, which is known as a raw material for solar power generation panels, generates 2 tons of waste. As the demand for PV panels increases, the problem of the treatment of polysilicon sludge is attracting attention, and studies on the utilization of polysilicon sludge are needed. Therefore, in this study, the applicability of polysilicon sludge treated as industrial waste to the lightweight panel for architectural purposes was examined.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.521-524
• /
• 2006

This study is about the production and properties of waste concrete powder that recycling aggregate is crushed to the waste concrete. We researched the generation and the disposal of recycled concrete powder. It is chemica] and physical features that is compared and analysis according to its production system and repeated crushing of time. Recycled concrete powder is more generated wet process than drying process. In addition, the more it is repeated crushing of time, the more recycled concrete powder is generated. Recycled concrete powder is discovered that wet process is larger of the specific area, lower density and particle size.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.1
• /
• pp.12-18
• /
• 2003

Recently the research for utilization of waste heat produced from electric power plants, casting factories, heat treating factories or commercial building are being afforded by the need for energy saving. The objective of this study is to develop a thermoelectric generation system which converts unused energy from close-at-hand sources such as garbage incineration heat and industrial exhaust etc. into electricity. This paper presents a thermoelectric technology on a optimum system design method and efficiency and cost effective thermoelectric element on order to extract the maximum power output from energy conversion of waste energy. It is shown that the longitudinal stresses of module contacted with two point constrained AI tubes could be released more than those with a one-point constrained.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.50-53
• /
• 2001

In this paper, we applied the Utility Interactive Photovoltaic-Wind Hybrid Generation System for stock raising waste disposal system. For the power consumption reduction of proposed system, we used the electromotive control system. So as to verify the propriety of proposed system, we made a Pilot Plant and examined the system.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.15 no.1
• /
• pp.65-82
• /
• 2017

The result of a preliminary safety assessment that was completed by applying the radionuclide inventory calculated on the basis of available data from radioactive waste generation agencies suggested that many difficulties are to be expected with regard to disposal safety and operation. Based on the results of the preliminary safety assessment of the entire disposal system, in this paper, a unit package exceeding the safety goal is selected that occupies a large proportion of radionuclides in intermediate-level radioactive waste. We introduce restrictions on the amount of radioactivity in a way that excludes the high surface dose rate of the package. The radioactivity limit for disposal will be used as the baseline data for establishing the acceptance criteria and the disposal criteria for each disposal facility to meet the safety standards. It is necessary to draw up a comprehensive safety development plan for the Gyeongju waste disposal facility that will contribute to the construction of a Safety Case for the safety optimization of radioactive waste disposal facilities.

• Resources Recycling
• /
• v.27 no.4
• /
• pp.3-15
• /
• 2018

Since the use of plastics in various goods such as film, containers, and packaging has been increasing in Korea, the generation of plastic waste is increasing. Plastic wastes are managed by waste charge system, Extended Producer Responsibility (EPR) system and voluntary agreement of plastic waste collection-recycling system. Recently, the management of plastic waste is becoming a social issues due to the refusal of the collection of plastic waste including waste plastic bag and waste vinyl. The ministry of environment in korea was set up the comprehensive plan for recycling waste management in accordance with the circulation cycle of manufacturing and production - distribution and consumption - separate and discharge - collection and sorting - recycling. In this study, the improvements for management of plastic waste were suggested with the review of domestic waste plastics management and the comprehensive plan by the ministry of environment.