• 한국지하수토양환경학회지:지하수토양환경
• /
• 제15권2호
• /
• pp.47-54
• /
• 2010

Although the demands for the dredging work have been increasing due to social and industrial reasons including national plan for restoration of four major rivers, environmental standards or management guidelines for the dredged river sediment are limited. The suggested environmental standard for the beneficial use of dredged river sediment consists of two levels, recyclable and concern, and includes eight contaminants such as metals and organic contaminants. The systematic approach to remediate dredged river sediment is also suggested. The system consists of both washing and stabilization processes with continuous multi particle separation. In the early stage, the sediments are separated into two particle sizes. The coarse-grained sediment over 0.075 mm, generally decontaminated with less trouble, follows normal washing steps and is sent for recycling. The fine-grained sediments under 0.075 mm are separated again at 0.025 mm. The particles bigger than this second separation point are treated in two ways, advanced washing for highly contaminated sediments and stabilization for less. The lab test results show that birnessite and apatite are most effective stabilizing agents among tested for Cd and Pb. The most fine residues, down-sized by continuous particle separation, are finally sent for disposal. The system is tested for metals in this study, but is expected to be effective for organic contaminants included in the environmental standard, such as PAH and PCE. The feasibility test on the field site will be followed.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제26권5호
• /
• pp.9-19
• /
• 2021

This study evaluated the feasibility of combined use of physical separation and soil washing to remediate heavy metals (Pb and Cu) contaminated soil in a military shooting range. The soils were classified into two types based on the level of heavy metal concentrations: a higher contaminated soil (HCS) with Pb and Cu concentrations of 6,243 mg/kg and 407 mg/kg, respectively, and a lower contaminated soil (LCS) with their concentrations of 1,658 mg/kg and 232 mg/kg. Pb level in both soils exceeded the regulatory limit (700 mg/kg), and its concentration generally increased with decreasing soil particle size. However, in some cases, Pb concentrations increased with increasing soil particle size, presumably due to the presence of residues of bullets in the soil matrix. As a pretreatment step, a shaking table was used for physical separation of soil to remove bullet residues while fractionating the contaminated soils into different sizes. The most effective separation and fractionation were achieved at vibration velocity of 296 rpm/min, the table slope of 7.0°, and the separating water flow rate of 23 L/min. The efficiency of ensuing soil washing process for LCS was maximized by using 0.5% HCl with the soil:washing solution mixing ratio of 1:3 for 1 hr treatment. On the contrary, HCS was most effectively remediated by using 1.0% HCl with the same soil:solution mixing ratio for 3 hr. This work demonstrated that the combined use of physical separation and soil washing could be a viable option to remediate soils highly contaminated with heavy metals.

• 한국잠사곤충학회지
• /
• 제23권1호
• /
• pp.47-55
• /
• 1981

絹織物加工을 實需要者의 利用度를 增加시키기 爲해 多年間 여러 사람에 의하여 硏究되어 왔으나 天然織維이기 때문에 加工方式으로 性質을 變化시키기는 어려워서 滿足스러운 精度로 이루어지지 못하고 있는 實情에 있다. 絹織物加工은 勿論 그 缺點을 補强하는 同時에 商品的價値도 向上시키는데 目的이 있는데 때로는 有名商標가 品質以上으로 販賣를 左右하는 例도 많다. 特히 絹制品은 歡迎을 받지 못하고 있는 實情에 있다. 이러한 問題點을 解決하기 爲해 筆者는 多年間 硏究를 持績하여 왔든바 一般絹織物의 浸潤後 乾燥時間보다 半減된 時間에 乾燥되는 所謂 Wash and Wear絹加工方法의 開發을 하기에 이르렀다. 그리고 그 加工費用이 極히 經濟性인 탓으로 아무런 부담감 없이 加工處理할 수 있는 特徵을 갖이고 있었다. 1. 繭絲는 吐絲營繭曲線이 S字型으로 되어 있어 浸潤時에는 原狀復舊의 性質이 있어 屈曲狀態를 이룩하게 되어 本加工絹織物이 Wash and Wear이기는 하나 가벼운 다림질이 必要하였다. 2. 이러한 加工은 絹絲蛋白質의 變性을 加工過程에서 1% D.I.S.溶液에 3時間 處理하여 變性誘發시킴으로서 可能하였다. 3. 加工絹의 防皺度, 剛乾度를 洗濯回數를 反復하면서 調査하여 본 結果 未處理絹보다 惡化되지 않았다. 4. 未加工絹도 水洗, 乾燥를 反復하게되면 스스로 變性되는 事實을 알았다. 5. 處理絹과 未處理絹의 强力伸度面의 差異가 없었다.

• Journal of Microbiology and Biotechnology
• /
• 제17권5호
• /
• pp.784-791
• /
• 2007

The present work aims to use a biofilter technology(aerated submerged filters) for the aerobic transformation at laboratory-scale of olive washing water(OWW) generated in the first steps of olive oil processing, as well as the genetic profiling and identification to the species level of the bacteria involved in the formation of the biofilm, by means of TGGE. Chemical parameters, such as biological oxygen demand at five days($BOD_5$) and chemical oxygen demand(COD), decreased markedly(up to 90 and 85%, respectively) by the biological treatment, and the efficiency of the process was significantly affected by aeration and inlet flow rates. The total polyphenol content of inlet OWW was only moderately reduced(around 50% decrease of the inlet content) after the biofilter treatment, under the conditions tested. Partial 16S rRNA genes were amplified using total DNA extracted from the biofilm and separated by TGGE. Sequences of isolated bands were mostly affiliated to the $\alpha-subclass$ of Proteobacteria, and often branched in the periphery of bacteria] genera commonly present in soil(Rhizobium, Reichenowia, Agrobacterium, and Sphingomonas). The data obtained by the experimentation at laboratory scale provided results that support the suitability of the submerged filter technology for the treatment of olive washing waters with the purpose of its reutilization.

• Safety and Health at Work
• /
• 제4권2호
• /
• pp.100-104
• /
• 2013

Background: The aim of this study was to assess public and private medical diagnostic laboratories in Nigeria for the presence of biosafety equipment, devices, and measures. Methods: A total of 80 diagnostic laboratories in biosafety level 3 were assessed for the presence of biosafety equipment, devices, and compliance rate with biosafety practices. A detailed questionnaire and checklist was used to obtain the relevant information from enlisted laboratories. Results: The results showed the presence of an isolated unit for microbiological work, leak-proof working benches, self-closing doors, emergency exits, fire extinguisher(s), autoclaves, and hand washing sinks in 21.3%, 71.3%, 15.0%, 1.3%, 11.3%, 82.5%, and 67.5%, respectively, of all laboratories surveyed. It was observed that public diagnostic laboratories were significantly more likely to have an isolated unit for microbiological work (p = 0.001), hand washing sink (p = 0.003), and an autoclave ($p{\leq}0.001$) than private ones. Routine use of hand gloves, biosafety cabinet, and a first aid box was observed in 35.0%, 20.0%, and 2.5%, respectively, of all laboratories examined. Written standard operating procedures, biosafety manuals, and biohazard signs on door entrances were observed in 6.3%, 1.3%, and 3.8%, respectively, of all audited laboratories. No biosafety officer(s) or records of previous spills, or injuries and accidents, were observed in all diagnostic laboratories studied. Conclusion: In all laboratories (public and private) surveyed, marked deficiencies were observed in the area of administrative control responsible for implementing biosafety. Increased emphasis on provision of biosafety devices and compliance with standard codes of practices issued by relevant authorities is strongly advocated.

• 패션비즈니스
• /
• 제16권3호
• /
• pp.13-31
• /
• 2012

The purpose of the study was to analyze the work clothes' clothing comfort and wearer mobility of painting workers with the consideration of the work environment features in the machine and shipbuilding industries in South Korea. A questionnaire survey was conducted for the study, which consisted of questions on the clothing comfort and wearer mobility aspects of painting work clothes by clothes types and body parts. The work clothes' clothing comfort and wearer mobility levels were scaled in 5 points i.e. 1(: very tight/very uncomfortable) to 5(: very slack/very comfortable). The painting work environmental hazardous features were considered as high impact levels of workplace temperature, oxygen deficiency, organic solvent, toxic gas factors while metal fragment factor only impacts 'low' in the painting processes with the findings throughout this study. Since the painting work consisted of surface washing and the spray and touch-up painting processes, which was carried out in an outdoor work place, the painting work clothes should meet high performance of waterproofing from the painting material and air permeability specially in summer as well as thermal performance in winter. The subjects painting workers' assessment of the existing work clothes' clothing oppression was in the levels between 3 (i.e. moderate) and 4 (i.e. comfortable) in a range of 1 to 5 points. The existing painting work clothes' wearer mobility was evaluated 'very uncomfortable' in all work clothes parts, especially, armhole length, biacromial breadth, sleeve length of the jumper; and body rise, waist, hip, thigh and knee circumferences of the pants.

• Safety and Health at Work
• /
• 제11권3호
• /
• pp.372-377
• /
• 2020

Infection risks of handling specimens associated with severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) by public health laboratory services teams were assessed to scrutinize the potential hazards arising from the work procedures. Through risk assessments of all work sequences, laboratory equipment, and workplace environments, no aerosol-generating procedures could be identified except the procedures (mixing and transfer steps) inside biological safety cabinets. Appropriate personal protective equipment (PPE) such as surgical masks, protective gowns, face shields/safety goggles, and disposable gloves, together with pertinent safety training, was provided for laboratory work. Proper disinfection and good hand hygiene practices could minimize the probability of SARS-CoV-2 infection at work. All residual risk levels of the potential hazards identified were within the acceptable level. Contamination by gloved hands was considered as a major exposure route for SARS-CoV-2 when compared with eye protection equipment. Competence in proper donning and doffing of PPE accompanied by hand washing techniques was of utmost importance for infection control.

• 한국의류학회지
• /
• 제33권8호
• /
• pp.1315-1324
• /
• 2009

This study is on the consolidation process of the conservation process of fabric with golden thread found in relics. Gold film was glued to pieces of Korean paper and satin using hide glue, which is a natural adhesive and resin Paraloid B-72, which is a liquid type adhesive. This study examines the types and concentration of the adhesives that are appropriate for consolidating gold film on fabric. The advantage of hide glue is that it is harmless to humans and has a high stability. This glue is also believed to be the closest to the adhesive that was used when the relic was originally made. Its weakness is that it is stiff and weaker than chemical glues, but after being washed with water the adhesion level increases. Therefore, hide glue is appropriate in the following instances: a) when washing after consolidation b) when the substrate of gold threads are significantly damaged, and c) when treating greater sized relics that take a longer time to work on. However, Paraloid B-72 has a better adhesion and flexibility than hide glue, but tends to spread out into a greater area, and the area where it is applied tends to absorb less water than before the application. In addition, it is noxious and can be harmful in long-term exposure. Therefore, Paraloid-72 is appropriate in the following instances: a) when consolidating the fabric after washing, and b) when working on smaller relics and consolidating smaller parts of a relic. The necessary concentration levels for consolidants for gold film are 30% for liquid type hide glue and at least 10% for Paraloid B-72 in order for the gold film to stay intact on the fabric during washing, consolidation, exhibition, and conservation.

• 한국환경과학회지
• /
• 제24권1호
• /
• pp.73-79
• /
• 2015

The objective of this work was to treat complex mal-odor of food waste with micro-bubbles from enhanced wet scrubber system, where the pilot plant was operated. Micro bubbles from the enhanced reactor of venturi scrubber were successfully generated through the air atomizing process with high velocity more than 60 m/sec and played an important role in the removal of mal-odor. Mal-odor was effectively changed into the micro-bubble and treated with washing chemicals together. Through establishing two series connection of the reactors, 85.2 % removal efficiency of complex mal-odor was obtained in case of average 940 times of input air. 0.35 kg/hr of sulfuric acid, 0.188 kg/hr of sodium hydroxide and 0.043 kg/hr of hypochlorite were injected for chemical washing.

• 한국재료학회지
• /
• 제12권12호
• /
• pp.924-929
• /
• 2002

To recycle waste materials, this work was focused on development of glass-ceramic from incinerator fly ash with a large content of Cl and its physical property was evaluated. In the process, water washing as a pre-treatment before melting the fly ash was used to remove large amount of Cl component in the ash and to reduce melting temperature. As a result, glass was obtained at below $100^{\circ}C$ compared to the melting temperature before washing the ash. Also, internal crystallization occurred under single stage heat treatment (at $850-950^{\circ}C$ for 20-340min) without adding other materials into the ash. It was shown that the glass-ceramic was composed of four crystals, diopside, anorthite, akermanite, and unknown phase. Hardness of 8.3GPa was found in the glass-ceramic, which is a high value compared to reported others. Thus, the present process suggests that a good glass-ceramic produced from an incinerator ash could be applicable for structural materials in terms of economic and environmental points.