• Journal of Environmental Science International
• /
• v.19 no.6
• /
• pp.665-670
• /
• 2010

Pollutants from urban pavement consists various kinds of substances which are originated from dry deposition, a grind out tire, corrosive action of rain to pavement and facilities and raw materials of the road etc.. These are major pollutants of urban NPS (Non-point source) during rainfall period. However there is not enough information to control such pollutants for appropriate management of natural water quality. In this study of transportation areas, three monitoring stations were set up at trunk road, urban highway and national road in Gyeongnam province. Runoff flow rate was measured at every 15minutes by automatic flow meters installed at the end of storm sewer pipe within the road catchment area for water quality analysis. Data was collected every 15 minutes for initial two hours of rainfall. Additional samples were collected 1-4 hours interval till the end of rainfall. The monitoring parameters were $COD_{Mn}$, SS, T-N & T-P and heavy metals. The average EMCs of TSS and $COD_{Mn}$ were 62.0 mg/L and 24.2 mg/L on the city trunk road, which were higher than those of urban highway and national road, indicating higher pollutant loads due to activities in the city downtown area beside the vehicle. On the other hand, the average EMC of T-N and T-P were in the range of 2.67-3.23 mg/L and 0.19-3.21 mg/L for all the sampling sites. Heavy metals from the roads were mainly Fe, Zn, Cu and Mn, showing variable EMCs by the type of road. From the TSS wash-off analysis in terms of FF(first flush) index, first flush phenomenon was clearly observed in the trunk road(FF : 0.89-1.43). However, such mass delivery behavior was not apparently shown in urban highway(FF : 0.90-1.11) and national road(FF : 0.81-1.41).

• Journal of Environmental Health Sciences
• /
• v.35 no.1
• /
• pp.36-44
• /
• 2009

Hand-washing has been recognized as a critical factor in controlling infection and cross-contamination. This study was performed to investigate hygienic behavior of male university students focusing on awareness of hand-washing, their hand washing practices, and the difference between their awareness and practices. Both a self-administered questionnaire survey and a separate direct observation in restrooms were carried out at a university campus over a four week period. In the survey, 93.6% of the responded students claimed to wash their hands after using toilet. However, just 16.9% of the observed students actually did so, according to a separate and unnoticed observational study. Among the observed students who washed their hands, 25.0% of them used soap, only 5.0% of them washed four parts of their hands, and 15.0% of them washed their hands for more than 10 seconds. Paper towel was the most common hand drying method in the direct observation and also in the survey. Significant differences between the questionnaire survey and the direct observation (p<0.0l) were found in hand-washing practices, duration of hand-washing, using soap, washing parts of the hand, and hand-drying method after using the toilet. This study indicates that there is a remarkable difference between the male university students' awareness of hand-washing and their hand-washing practices. This study reveals that there is the need for programs or campaigns to increase hand-washing practices of male university students.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.3
• /
• pp.375-382
• /
• 2010

In this study, we developed a method to predict the residual stress distribution and thermal deformation caused by in-mold labeling (IML) processes. IML is one of the injection molding processes for injecting a material into a cavity and subsequently inserting a decorated film. The IML process can yield products with decorations of outstanding excellent quality in only one working step. Although the IML process has various advantages, it causes defects such as film delamination, wash-out, and flow marks. In particular, deformation is considered to be a major concern in terms of delamination. To validate the model, the deformation predicted by using a numerical model was compared with experimental results, and both results showed good agreement. We verified that the developed method can be used to obtain the design guidelines for preventing delamination in the initial design stage of the IML process.

• Journal of International Academy of Physical Therapy Research
• /
• v.11 no.2
• /
• pp.2021-2027
• /
• 2020

Background: Previous robot-mediated gait training has been proven several limitations such as pointless repeated motion training, decreased presence, etc. In this research, adult stroke patients were participated in robot-mediated gait training accompanied with or without virtual reality program. Objectives: Exploring whether the results indicated virtual reality system has contribution to muscle strength and balance ability. Design: A case series research, cross-over trial. Methods: Eleven participants (male 4, female 7) with adults diagnosed as stroke from medical doctor ware engaged. The participants received 2 treatment sessions of identical duration, robot-assisted gait training with virtual reality and robot-assisted gait training with screen-off randomly crossed over include 1-day for each person of wash-out period. The parameter was muscle activity, the researchers assessed sEMG (surface electromyography). Results: The result showed less muscle activities during training in robot-assisted gait training with virtual reality circumstances, and these indicated muscles were gluteus medius muscle, vastus medialis muscle, vastus intermedius and vastus lateralis muscle, semimembranosus muscle, gastrocnemius-lateral head, and soleus muscle (P<.05). Conclusion: In this study, we analyzed the outcome of muscle activity for clinical inference of robot-assisted gait training with virtual reality (VR). Less muscle activity was measured in the treatment accompanied by VR, therefore, a more systematic, in-depth and well-founded level of follow-up research is needed.

• Journal of Oral Medicine and Pain
• /
• v.40 no.1
• /
• pp.10-16
• /
• 2015

Purpose: Pilocarpine has the effects on improvement of salivary flow and subjective symptoms for xerostomic patients. Because of unwanted side effects following its systemic administration, topical pilocarpine has been paid attention as an alternative. This study aimed to investigate effects of pilocarpine solution as mouthwash on salivary flow and adverse effects compared to systemic administration of 5 mg pilocarpine tablet in healthy subjects. Methods: The study was a double blind, placebo-controlled, crossover clinical trial. Five milligrams pilocarpine tablets, 4 mL of 2% pilocarpine solution and placebo solution were given to 12 healthy volunteers (6 males and 6 females) in a predetermined order with wash-out period of at least two days and unstimulated whole saliva was collected before and after administration of each drug. Blood pressure and pulse rate was also measured and subjective effect and potential side effects were evaluated by a self-administrated questionnaire. Results: Systemic (5 mg tablet) and topical (2% solution) use of pilocarpine significantly increased salivary flow rate in healthy subjects compared to placebo (p<0.001). In both the pilocarpine solution and tablet groups, salivary flow rates at 120 minutes after administration remained increased. Subjective effect on salivation was the largest in the pilocarpine tablet group, followed by the pilocarpine solution group (p<0.05). There was no significant difference in blood pressure and pulse rate after administration of all three drugs. Fewer side effects reported in the pilocarpine solution group than in the tablet group. Conclusions: Two percents pilocarpine solution as mouthwash increases salivary flow rate, definitely superior to placebo solution and comparable to pilocarpine tablet, with fewer side effects in healthy subjects. It indicates a possibility of pilocarpine solution as a useful alternative of pilocarpine tablets for the xerostomic patients with systemic diseases.

• The Research Journal of the Costume Culture
• /
• v.13 no.4 s.57
• /
• pp.540-549
• /
• 2005

It was the purpose of this study to investigate the effect of chitosan treatment and mordanting on the air-permeability, fastness of the dyestuff to washing, fastness of the dyestuff to light, and antimicrobial effect of cotton and nylon fabrics dyed using Rhusjara ica. In the dyeing experiment, examinations were made on the difference between the chitosan treated fabrics and chitosan untreated fabrics, and on the difference according to the type of mordanting agents and the mordanting methods. Dyeing was carried out for the chitosan treated and untreated fabrics under the conditions of non-mordanting and Al, Sn, Fe mordanting. As a result, due to the dye-uptake of the dyestuff component of the Rhusjara ica, the air-permeability values decreased considerably. And due to the action of the mordanting agents, the air-permeability decreased also. The air-permeability decreased more conspicuously in the case of the dyestuffs uptake to the chitosan components than in the case of the dyestuffs uptake to the cotton fibers or nylon fibers. Nylon dyed fabric exhibited better wash fastness than the cotton dyed fabric. As the number of washing increased, the color of the cotton fabric specimens and nylon fabric specimens, dyed using Rhusjara ica, shifted toward yellowish. The light fastness values were in the range of grade 1${\~}$2, which were very inferior. The light fastness values did not improve according to the mordanting or to the chitosan treatment. In the case of chitosan untreated fabrics dyed using Rhusjara ica, the growth rate of the bacteria promoted, on the contrary, compared to that of the control white fabric.

• Journal of Environmental Science International
• /
• v.17 no.12
• /
• pp.1353-1361
• /
• 2008

Quality control of Argo(Array for Real-time Geostrophic Oceanography) data is crucial by reason that salinity measurements are liable to experience some drift and offset due to biofouling, contamination of sensor and wash-out of biocide. The automated Argo real-time quality control has a limit of sorting data quality, so that WJO program is adopted as standardized method of Argo delayed mode quality control (DMQc) in the world that is a precise quality control method. We conducted DMQC on pressure, temperature and salinity measured by Argo floats in the Pacific Ocean including expert evaluation. Particularly, salinity data were corrected using WJO program. 4 salinity profiles of Argo delayed mode were compared with nearby in situ CTD data and other Argo data in deep layer where oceanographic conditions are stable in time and space. The differences of both salinities were lower than target accuracy of Argo. As compared with the difference of salinities before DMQC, those after DMQC decreased by 60-80 percent. Quality of delayed mode salinity data seemed to be improved correcting salinity data suggested by WJO program.

• The Korean Journal of Pesticide Science
• /
• v.9 no.4
• /
• pp.354-358
• /
• 2005

The study was carried out to investigate dissipation pattern of pesticide residue in/on different varieties of lettuce applied with foliar spraying under greenhouse. The initial deposited amount of alpha-cypermethrin and imidacloprid in/on the crop was entirely corresponded with shape of the crop. Dissipation of deposited pesticide residue was supposed to be related with degradation by sunlight and wash off by watering rather than dilution effect by biomass increase. The crop grouping in leaf vegetables has to be carefully considered even in lettuce for dissipation pattern of pesticide residue; head type and leafy type.

• Journal of radiological science and technology
• /
• v.24 no.2
• /
• pp.65-70
• /
• 2001

The purpose of this study is to prevent nosocomial infection in patients through contact of radiographic cassettes. Data were collected from radiographers working in 29 university hospitals in Seoul in February and March 2001. Radiographic cassettes were disinfected daily in 5 hospitals, weekly in 4 hospitals, monthly in 5 hospitals, bimonthly in 1 hospital and once every three months in another hospital. 12 other hospitals do not practice regular disinfections of radiographic cassettes. Gauze soaked in disinfectant solution is used in 7 hospitals while 11 hospitals used cotton and cloth soaked in disinfectant solution to clean the radiographic cassettes. 26 hospitals used 99% alcohol based disinfectant solutions while 3 hospitals used 75% alcohol based disinfectant. 26 hospitals use of intercourse cassettes outpatients and in patients. In 26 hospitals, all patients shared the same set of radiographic cassettes used in the hospitals, or in 26 hospitals, separate sets of radiographic cassettes are used for outpatients and inpatients. Separate sets of cassettes are used for ICU and inpatients in 6 others hospitals. 23 hospitals used the same sets of radiographic cassettes for all their patients. radiographic cassettes are cleaned in wash area in the study room of the radiographic department in 17 hospitals. 12 other hospitals do not have designated cleaning areas for the cassettes. All radiographers practiced hands washing with soap. All 29 hospitals surveyed have infection control committee. However, only 9 out of the 29 hospitals surveyed provided Infection disinfections control education to radiographers. Only 3 hospitals have radiographers sitting in the infection control committee. Infection management education is conducted in 63 hospitals annually, twice a year in 1 hospital and once every 3 months in 2 hospitals.

• KSBB Journal
• /
• v.8 no.3
• /
• pp.217-223
• /
• 1993

Methods for production of ${\gamma}$-Polyglutamic acid( ${\gamma}$-PGA ) by an alkalophilic Alcaligenes sP. were investigated for batch and continuous culture processes. Both quantity and productivity of ${\gamma}$-PGA by Alcaligenes sp. in batch culture were gradually increased with the increase of glucose concentration up to 50g/l , but the maximal production yield of 63% was obtained at 10g/l of glucose concentration. The highest specific growth rate was about $0.25hr^{-1}$ at 50un of glucose concentration, and substrate inhibition was observed at above 50g1f of glucose concentration. The highest ${\gamma}$-PGA formation about 11g/l in a batch system was obtained at 31'C, pH 10.0 and 87rpn Productivity of 2.80g/l/hr for continuous cultivation was 9 times higher than the productivity for batch cultivation.