• Journal of the Korea Concrete Institute
• /
• v.21 no.3
• /
• pp.283-290
• /
• 2009

Differently from fly ash, the bottom ash produced from thermoelectric power plant has been treated as an industrial waste matter, and almost reclaimed a tract from the sea. If this waste material is applicable to foam concrete as an aggregate owing to its light-weight, however, it may be worthy of environmental preservation by recycling of waste material as well as reducing self-weight of high-rising structure and horizontal forces and deformations of retaining wall subject to soil pressure. This study has an objective of evaluating the effects of application of bottom ash on the mechanical properties of foam concrete. Thus, the ratio of bottom ash to cement was selected as a variable for experiment and the effect was measured in terms of unit weight of concrete, air content, water-cement ratio and compressive strength. It can be observed from experiments that the application ratios have different effects on the material parameters considered in this experiment, thus major relationships between application ratio and each material parameter were finally introduced. The result of this study can be applied to decide a mix design proportion of foam concrete while bottom ash is used as an aggregate of the concrete.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.8
• /
• pp.37-44
• /
• 2013

The superiority of bearing ground anchor system has been recognized for the stability and economical efficiency since 1950s in Japan, Europe and etc. The ground anchor introduced in Korea, however, has the structural problem that the tensile strength comes only from the ground frictional force caused by the expansion of the wedge body and it is impossible to evaluate the bearing resistance because the adhering method of the anchor body to hollow wall is not appropriate. In this study, the underreamed ground anchor system was developed so that the bearing pressure of ground anchor can exert as much as possible. And the in-situ tests were performed to evaluate the pullout behavior characteristics and to verify the decreasing effect of the bonded length. The pullout tests were performed with the non-grouted tension condition and grouted tension condition in order to identify the pull-out resistance of each conditions. In addition, it was compared with the results of friction anchor. Finally, the numerical analysis was fulfilled to verify the bearing effect at the bonded part through the detailed modeling by PLAXIS-2D, which is general finite element method analysis program.

• Journal of Korean Ophthalmic Optics Society
• /
• v.7 no.2
• /
• pp.209-215
• /
• 2002

This study investigated the crystal growth, crystalline structure and the basic optical properties of $SnSe/BaF_2$ epilayers. The SnSe epilayer was grown on $BaF_2$(111) insulating substrates using a hot wall epitaxy(HWE) technique. It was found from the analysis of X-ray diffraction patterns that $SnSe/BaF_2$ epilayer was growing to single crystal with orthorhombic structure oriented [111] along the growth direction. Using Rutherford back scattering(RBS), the atomic ratios of the SnSe was found to be stoichiometric, almost 50 : 50. The best values for the full width at half maximum (FWHM) of the DCXRD was 163 arcsec for SnSe epilarer. The epilayer-thickness dependence of the FWHM of the DCXRD shows that the quality of the $SnSe/BaF_2$ is as expected. The dielectric function ${\varepsilon}$(E) of a semiconductor is closely related to its electronic energy band structure and such relation can be drawn from features around the critical points in the optical spectra. The real and imaginary parts(${\varepsilon}_1$ and ${\varepsilon}_2$) of the dielectric function ${\varepsilon}$ of SnSe were measured. These data are analyzed using a theoretical model known as the model dielectric function(MDF). The optical constants related to dielectric function such as the complex refractive index(n*-n+ik), absorption coefficient (${\alpha}$) and normal- incidence reflectivity (R) are also presented for $SnSe/BaF_2$.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.29 no.6
• /
• pp.286-304
• /
• 2017

In this study, we proposed a new-type of circular perforated caisson breakwater consisting of a bundle of latticed blocks that can be applied to a small port such as a fishing port, and numerically investigated the hydraulic characteristics of the breakwater. The numerical method used in this study is OLAFOAM which newly added wave generation module, porous media analysis module and reflected wave control module based on OpenFOAM that is open source CFD software published under the GPL license. To investigate the applicability of OLAFOAM, the variations of wave pressure acting on the three-dimensional slit caisson were compared to the previous experimental results under the regular wave conditions, and then the performance for irregular waves was examined from the reproducibility of the target irregular waves and frequency spectrum analysis. As a result, a series of numerical simulations for the new-type of circular perforated caisson breakwaters, which is similar to slit caisson breakwater, was carried out under the irregular wave actions. The hydraulic characteristics of the breakwater such as wave overtopping, reflection, and wave pressure distribution were carefully investigated respect to the significant wave height and period, the wave chamber width, and the interconnectivity between them. The numerical results revealed that the wave pressure acting on the new-type of circular perforated caisson breakwaters was considerably smaller than the result of the impermeable vertical wall computed by the Goda equation. Also, the reflection of the new-type caisson breakwater was similar to the variation range of the reflection coefficient of the existing slit caisson breakwater.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.1
• /
• pp.57-65
• /
• 2017

During a construction of embankment, sub base, or retaining wall backfill, the speedy measurement of water content is necessary. In this study, a test method for field determination of water content of soil by the calcium carbide gas pressure (speedy water content measurement method) was evaluated for its reliability and accuracy. Dry oven and microwave oven methods were also used for water content measurement. In the test, weathered granite and Nakdong River sand in the site and kaolinite were used for water content measurement. The mass of 20, 22, 24, 26, 28, and 30 g of soil was respectively tested for 1, 3, and 5 min. The effect of each sample on water content was compared one another and analyzed. As the mass and testing time increased, the water content increased. The amount of soil was more important factor than testing time for the speedy water content measurement. In order to obtain similar result to that of dry oven method, 3 min of testing time with 24 g of soil was necessary for weathered granite classified as SM and 3 min with 30 g for Nakdong River sand classified as SP. For Nakdong River sand with 20-50% of kaolinite, the water content by speedy measurement increased as the clay content increased.

• Progress in Medical Physics
• /
• v.11 no.2
• /
• pp.109-116
• /
• 2000

One consideration of radiation delivery in cervical cancer is the complication of critical organs, e.g., bladder and rectum. The absorbed dose of bladder and rectum in HDR intracavitary brachytherapy is measured indirectly with TLD dosimetry A method for the complication reduction of bladder and rectum is suggested. For two-hundred cervical cancer patients, follow-up MRI images were reviewed and distances from cervical central axis to bladder and rectum and vaginal wall thickness were measured. The sealed TLDs were placed upon the gauze packing of the ovoids and the distances to the TLDs from the ovoid center were measured in the simulation film and actual doses of bladder and rectum were calculated. From published data, maximal tolerance doses of bladder and rectum were derived and based on the permissible doses per fraction in HDR brachytherapy the packing thicknesses were determined in both directions. The required minimal packing thicknesses for bladder and rectum were 0.43 and 0.92 cm, respectively. The results were compared with computer calculation using the Meisberger polynomial approach. It is our hope this study can be used for a guideline for users in clinic in estimating critical organ dose in bladder and rectum in HDR brachytherapy in vivo dosimetry.

• The Plant Pathology Journal
• /
• v.25 no.1
• /
• pp.86-90
• /
• 2009

In November 2008, typical powdery mildew symptoms were observed on leaves of Arabidopsis thaliana ecotype Col-0 plants in a growth room under controlled laboratory conditions at Korea University, Seoul. The disease was characterized by the appearance of white powder-like fungal growth on the surface of infected leaves. As the disease progressed, infected leaves exhibited chlorotic or necrotic brown lesions, and leaf distortion and senescence. Conidiophores of the causal fungus were hyaline, unbranched, 3-4 celled, cylindrical, and $80-115{\times}6-9{\mu}m$ in size. Singly produced conidia (pseudoidium type) were hyaline, oblong to cylindrical or oval in shape, and $26-55{\times}15-20{\mu}m$ in size with a length/width ratio of average 3, angular/rectangular wrinkling of outer wall and no distinct fibrosin bodies. Appressoria on the hyphae were multi-lobed. These structures are typical of the powdery mildew Oidium subgenus Pseudoidium, anamorph of the genus Erysiphe. The measurements of the fungal structures coincided with those of Erysiphe cruciferarum. The phylogenetic analysis using ITS rDNA sequences revealed that the causal fungus Erysiphe sp. KUS-F23994 is identical to E. cruciferarum. The isolated fungus incited powdery mildew symptoms on the inoculated Arabidopsis leaves, which proved Koch's postulates. Taken all data together, we first report the occurrence of powdery mildew disease of A. thaliana caused by Erysiphe cruciferarum in Korea.

• Journal of Korean Society of Steel Construction
• /
• v.26 no.6
• /
• pp.511-522
• /
• 2014

In this study, an innovative steel stair system is presented which enables rapid erection and high quality control in both residential and office building construction. This system features two lightweight steel stringers of box shape, bolted connections easy to absorb construction tolerance, and stair steps movable transversely (or sliding steps) such that the work space needed for concrete stairway wall could be easily provided. In this type of stairway system, other than providing robust connecting details, ensuring vibration performance is especially important since this system may be vibration-sensitive due to lightweight nature and/or probable low damping. To tackle these issues, a series of full-scale mock-up tests were conducted by using box-shape stringer members with or without concrete-fill. The connection system was shown to be sufficiently stiff and strong, or it remained elastic even under the 160% of service load level. Among the seven stringer alternatives, five exhibited satisfactory vibration performance according to the related North American and European acceptance criteria.

• Journal of Chest Surgery
• /
• v.33 no.5
• /
• pp.391-397
• /
• 2000

Background: Cardiac involvement of Behcets disease is very rate, however, the prognosis of Behcet disease depends on cardiovascular complications. In this article, we described surgical treatment of aortic insufficiency with Behcets disease. Material and Method: From March 1986 to February 1998, we operated on 10 patients of aortic insufficiency with Behcets disease. Male to female ratio was 8 to 2, and age ranged from 21 to 40 years(mean 32.8 years). There were 8 patients with evidence of Behcets disease and another 2 patients had some suspicious findings of Behcets disease(i.e., prosthetic value dehiscence, hypertrophied aortic wall). Adequate preoperative medical treatment for Behcets disease was done in 3 patients. Result: We performed 24 open heart surgeries in 10 patients. Redo value replacements using prosthetic valves were done in 4 patients. Among them, 2 patients were operated on for a second redo valve replacement and one of them operated on for a 4th and 5th operation because of recurrent paravalvular leakage. These 4 patients expired. 1 patient who had undergons tissue value replacement is alive. 1 patient who underwent Cabrol operation expired dut to rupture of graft anastomosis site. We used homografts in 3 patients. In 2 of them, we performed aortic root replacement and subcoronary valve replacement in another patient. The patient who underwent subcoronary valve insertion had remnant aortic insufficiency, so we are closely observing him. We also performed Ross operation in a 24 year old female who suffered severs aortic insufficiency and endocarditis after aortic valvuloplasty. 5 patients are alive and mean follow up duration is 49.0 months. Among them, we used homografts or sutografts in 4 patients. We could observe excellent clinical results in the patients who underwent aortic root replacement using homograft and they were treated medically for Behcets disease. Conclusion: We concluded that adequate preporative diagnosis, clinical suspicion, and periopertive medical treatment for Behcets disease are very important for the result of surgical management of aortic insufficiency with Behcets disease. The use of homograft or autograft was helpful for the healing of anastomosis site and we should carefully observe the long term follow up results.

• Journal of Biomedical Engineering Research
• /
• v.30 no.5
• /
• pp.401-411
• /
• 2009

In this paper, we correct pulse wave velocity(PWV) with heart-rate and derive regression equations to estimate intima-media thickness(IMT). Widely used methods for diagnosis of arteriosclerosis are IMT and PWV. Arterial wall stiffness determines the degree of energy absorbed by the elastic aorta and its recoil in diastole but there is not correlation between sclerosis and IMT in an existing study. In this study, we will correct PWV with heart-rate and get regression equation to estimate IMT using heart-rate correction index(HCI). We executed experiments for this study. Made up question of physical condition and measured electrocardiogram(ECG), photoplethysmogram (PPG) of finger-tip and toe-tip and ultrasound image of carotid artery. Calculated PWV and IMT using ECG, PPG and ultrasound image. We found that every p-value between PWV and IMT is not significant(<0.05). But p-value between IMT and HCI which is a corrected PWV using heart-rate is significant(>0.01). We use HCI and various measured parameter for estimating regression equation and apply backward estimation to select parameters for regression analysis. Result of backward estimation, found that only HCI is possible to derive proper regression equation of IMT. Relationship between PWV and IMT is the second order. Result of regression equation of E-H PWV is $R^2$=0.735, adj $R^2$=0.711. This is the best correlation value. We calculate error of its analysis for verification of earlobe PWV regression equation. Its result is RMSEP=0.0328, MAPE(%) = 4.7622. Like this regression analysis, we know that HCI is useful parameter and relationship between PWV, HCI and IMT. In addition, we are able to suggest possibility which is that we can get different parameter of prediction throughout just one measurement.