• 한국지반신소재학회논문집
• /
• 제7권2호
• /
• pp.41-47
• /
• 2008

본 연구에서는 보강토옹벽 상부에 재하된 상재하중 및 보강재 종류의 변화에 따른 토목섬유 보강토옹벽의 벽체 변위 특성을 평가하기 위하여 일련의 모형실험을 수행하였다. 모형 보강토옹벽은 높이${\times}$길이${\times}$폭이 $100cm{\times}140cm{\times}100cm$인 모형토조 내에 축조하였다. 모형 보강토옹벽 축조시 뒤채움흙으로는 통일분류법상 SM으로 분류될 수 있는 화강풍화토를 사용하였고, 보강재로는 인장강도 특성이 다른 3종류의 토목섬유(지오네트 한 종류 및 지오그리드 두 종류)를 사용하여 총 7종류의 모형 보강토옹벽에 대한 실험을 수행하였다. 모형 보강토옹벽 축조후 상재하중 재하에 따른 벽체 변위를 LVDT를 이용하여 측정하였다. 모형실험 결과, 토목섬유 보강토옹벽의 최대 수평변위는 벽체 저면에서부터 0.7H지점에서 발생하고, 그 크기는 보강재의 인장강도가 증가할 수록 증가하는 것으로 나타났다. 또한 상재하중이 증가할수록 토목섬유 보강으로 인한 벽체변위의 감소율은 감소하였다.

• Earthquakes and Structures
• /
• 제9권6호
• /
• pp.1193-1219
• /
• 2015

The purpose of this study is to evaluate the seismic performance of high-rise reinforced concrete (RC) box-type wall structures commonly used for most residential buildings in Korea. For this purpose, an analytical model was calibrated with the results of the earthquake simulation tests on a 1:5 scale 10-story distorted model. This calibrated model was then transformed to a true model. The performance of the true model in terms of the stiffness, strength, and damage distribution through inelastic energy dissipation was observed with reference to the earthquake simulation test results. The model showed high overstrength factors ranging from 3 to 4. The existence of slab in this box-type wall system changed the main resistance mode in the wall from bending moment to tension/compression coupled moment through membrane actions, and increased the overall resistance capacity by about 25~35%, in comparison with the common design practice of neglecting the slab's existence. The flexibility of foundation, which is also commonly neglected in the engineering design, contributes to 30~50% of the roof drift in the stiff direction containing many walls. The possibility of concrete spalling and reinforcement buckling and fracture under the maximum considered earthquake (MCE) in Korea appears to be very low when compared with the case of the 2010 Concepcion, Chile earthquake.

• 한국터널지하공간학회 논문집
• /
• 제9권2호
• /
• pp.143-155
• /
• 2007

원형수직구 벽체에 작용하는 토압은 축대칭 아칭효과로 인하여 평면변형조건의 벽체에 작용하는 토압보다는 작으며, 원형수직구 흙막이벽이나 라이닝 등의 설계를 위해서는 벽체에 작용하는 토압의 정확한 산정이 필요하다. 따라서, 수평 및 연직방향 아칭효과에 의한 토압감소를 고려하고 수직구 벽체 반경에 대한 높이의 비로 정의되는 벽체형상비의 영향을 합리적으로 고려한 토압산정식이 제안되었다. 또한, 모래지반에서 모형실험에 의한 토압이 분석되었다. 제안된 토압산정식에 의한 토압은 벽체반경이 증가하여 벽체형상비가 감소함에 따라 평면변형조건의 토압과 정확히 일치하였으며, 모형실험에 의한 토압분포와 근사한 경향을 나타내었다.

• KIEAE Journal
• /
• 제3권2호
• /
• pp.37-44
• /
• 2003

The aim of this study was to analyze the thermal performance through Test-Cell of TI-wall in domestic climate. This study was carried out as follows: 1) The TI-wall was studied for ability to reduce heat loss through the building envelope and analyzed to TIM properties. 2) Test models of TI-wall were designed through the investigation of previous paper and work, measured for winter and spring, and the thermal effects were analyzed. The type of the TIM used in test model is small-celled(diameter 4mm and thickness 50mm) capillary and cement brick(density $1500kg/m^3$) was used by thermal mass. 3) Test-cell of TI-wall was calibrated from measured data and the dynamic simulation program ESP-r 9.0. In these simulations, the measured climate conditions of TaeJon were used as outdoor conditions, and the simulation model of Test-cell was developed. 4) The sensitivity analysis is executed in various aspects with standard weather files and ESP-r 9.0, and then most suitable system of TI-wall are predicted. Finally, The suitable system of TI-wall was analysed according to sizes of air gap, kinds, thickness, and the surface absorption of therm wall. The result is following. In TI-wall, Concrete is better than cement brick, at that time the surface absorption is 95%, and the most efficient thickness is 250mm. As smaller of a air gap, as reducer of convection heat loss, it is efficient for heating energy. However, ensuring of a air gap at least more than 50mm is desirable for natural ventilation in Summer.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 가을 학술발표회 논문집
• /
• pp.79-86
• /
• 2000

Recently, application of the reinforced earth wall is in increasing trend. Although many investigations on the influence of the length and spacing of reinforcement and the values of surcharge load has been carried out in the past, but the research about the influence of the location and value of surcharge loads has been scarce. Therefore this study was necessitated. The model test were carried out by varying the location and value of surcharge loads for two types of the backfill soils.

• Geomechanics and Engineering
• /
• 제15권2호
• /
• pp.775-781
• /
• 2018

Shake table tests were conducted on scaled tunnel model to investigate the mechanism and effect of seismic loadings on horseshoe scaled tunnel model in ground fissure site. Key technical details of the experimental test were set up, including similarity relations, boundary conditions, sensor layout, modelling methods were presented. Synthetic waves and El Centro waves were adopted as the input earthquake waves. Results measured from hanging wall and foot wall were compared and analyzed. It is found that the seismic loadings increased the subsidence of hanging wall and lead to the appearance and propagation of cracks. The values of acceleration, earth pressure and strain were greater in the hanging wall than those in the foot wall. The tunnel exhibited the greatest earth pressure on right and left arches, however, the earth pressure on the crown of arch is the second largest and the inverted arch has the least earth pressure in the same tunnel section. Therefore, the effect of the hanging wall on the seismic performance of metro tunnel in earth fissure ground should be considered in the seismic design.

• 한국지반공학회지:지반
• /
• 제14권5호
• /
• pp.67-76
• /
• 1998

본 연구에서는 보강토 구조물에 이용되는 지오그리드와 국내에 많이 분포하고 있는 화강풍화토를 대상으로 하여, 보강재의 포설깊이가 동일한 상태에서 보강재의 길이를 벽체높이의 0.465배, 0.685배, 0.9배로 설치하여 보강재가 전면벽체에 정착된 경우와 비정착된 경우에 대하여 모형실험을 실시하였다. 모형실험결과, 정착된 경우에는 보강재의 길이가 증가함에 따라 지지력은 무보강인 경우 보다 약 1.725~2.1배 증가함을 알 수 있었으며, 침하량도 약 20%이상의 감소율을 보였다. 전면 벽체의 최대 수평변위량은 무보강에 비해 약 80%이상의 감소율을 보였다. 비정착된 경우에도 무보 강인 경우보다 지지력이 약 1.7배이상 증가하였으며, 전면벽체의 최대 수평변위는 약 50%이상 감소하였다. 모형실험을 통해 고찰한 파괴면은 Bchlosser 등(1979)의 연구결과와 유사하게 나타났다.

• 한국지반공학회논문집
• /
• 제34권12호
• /
• pp.7-17
• /
• 2018

PHC-W흙막이벽체와 결합된 지하증설벽체의 테스트베드를 구축중에 있다. 지하증설벽체의 제원을 결정하기 위하여 실대형 지하증설벽체의 핵심 부재를 제작하여 휨강도실험 및 전단강도실험을 실시하였다. 원형 PHC말뚝의 단면 형상을 개량하여 개발된 PHC-W 흙막이벽체를 건축물 지하벽체로 활용하기 위하여 합성증설벽체와 비합성증설벽체를 제작하여 휨강도 및 전단강도 실험을 수행하였다. 합성증설벽체와 비합성증설벽체에서 휨모멘트 강도 실험값 및 전단강도 실험값이 유사한 수준으로 나타났으므로 합성증설벽체 대신에 시공이 간편하고 비용이 절감될 수 있는 비합성증설벽체를 적용할 수 있다는 것을 확인하였다. 실대형 모형 증설벽체는 두께 200mm로 제작되었는데, PHC-W 흙막이벽체와 결합된 지하증설벽체의 경우 동등 지하실 규모의 통상적인 지하벽체보다 두께를 100~200mm 정도 절감할 수 있는 것을 확인할 수 있었다.

• 한국군사과학기술학회지
• /
• 제22권5호
• /
• pp.637-643
• /
• 2019

Wind tunnel testing for flow-through model is necessary for performance prediction of an aircraft with air-breathing jet engine. Internal drag correction and wall correction are performed to acquire preciser wind tunnel test data. Many test runs are generally required to correct internal drag and wall interference in wind tunnel test. In this study we investigated more effective correction schemes using the response surface method. Even though the number of tests required for these schemes was much smaller than that for conventional methods, the differences between corrections using these schemes and conventional methods were similar level with the uncertainty of measurement except for the data near the boundaries.

• 한국지반환경공학회 논문집
• /
• 제14권9호
• /
• pp.39-47
• /
• 2013

Local deformations in back filling materials of two sands and one glass bead with different particle shapes behind a rigid retaining wall were studied. Two kinds of boundary conditions were compared: active wall translation and active rotation of the wall about its toe. Effect of the speed of active wall translation was also investigated. The digital image correlation method was used to analyze local deformation developments inside the materials. Test results showed that particle shape and density mainly influence the inclination angle and width of the shear band. The general shear band pattern is strongly dependent on the wall movement mode, while it was little influenced by particle shape. Within a limited range of wall speed in this study, shear band became wider and local deformation became larger with increase of wall speed.