• 대한설비공학회지:설비저널
• /
• 제13권1호
• /
• pp.14-21
• /
• 1984

The purpose of this investigation is to study heat transfer characteristics in wall jet region on a flat plate caused by upward impinging water jet. In the wall jet region, heat transfer results by impinging water jet are being compared with the ones with supplementary water. As the radius increases, the heat transfer coefficient in the wall jet region consquently decreases, but decreasing nozzle-heat plate distance, the reduction rate increases. The experimental equation is expressed as follows : $$\frac{N_{ur}}{P_r^{0.4}}{\cdot}\overline{\xi}=m(\overline{\eta}{\codt}Re{\delta})^n,\;m=0.034\~0.056,\;n=1.74\~2.007$$ The optimum height of supplementary water is obtained to improve heat transfer effect of wall jet region.

• 대한기계학회논문집
• /
• 제19권1호
• /
• pp.219-230
• /
• 1995

The flow characteristics of a two-dimensional offset jet issuing parallel to a rough wall is experimentally investigated by using a split film probe with the modified Stock's calibration method. The mean velocity and turbulent stresses profiles in the up and down-stream locations of the wall-attachment regions are measured and compared with those of the smooth wall attaching offset jet cases. It is found that the wall-attachment region on the rough wall is wider than on the smooth wall for the same offset height and the jet speed. The position of the maximum velocity point is farther away from the wall than that for the smooth wall case because of the thick wall boundary layer established by the surface roughness. It is concluded that the roughness of the wall accelerates the relaxation process to a redeveloped plane wall jet and produces a quite different turbulent diffusion behavior especially near the wall from comparing with the smooth plane wall jet turbulence.

• 대한기계학회논문집
• /
• 제7권4호
• /
• pp.361-371
• /
• 1983

The turbulent structures of the free plane jet and two dimensional impinging jet are investigated experimentally. In order to get the two dimensional jet, the contour of the cubic equation suggested by Morel is used for a contracting nozzle. A linearized constant-temperature hot-wire anemometer is used for measurement. Mean velocities and turbulent intensities are measured along the centerline of the jet. Jet halp width spatial double velocity correlation coefficients and integral length scales are obtained. It is established that the free plane jet is truly self-preserving about 40 slot widths downstream of the nozzle. The experiments for the impinging jet are carried out at four different impingement wall locations within the self-preserving region of the free plane jet, and comparing the results with that of free plane jet, the mean velocity is changed in the region of 0.25H and turbulent intensities are affected in the region of 0.2H from the wall, respectively, where H means the distance between the nozzle exit and the wall.

• 대한기계학회논문집
• /
• 제17권12호
• /
• pp.3166-3178
• /
• 1993

The turbulent flow characteristics of impinging jet have been investigated by the hot wire anemometry with a movable impinging wall. Turbulences were generated by the meshed jet as well as the typical round jet and their characteristics were compared, of mean velocity profiles, turbulent intensities. Reynolds stresses, similarities and their centerline flow behaviors. The meshed jet tends to make shear layer wider than the normal one in the initial region and the velocity profiles of the normal jet is rather contractive being compared with those of the meshed one near the wall. The effect of meshed exit appears only within 4D at the begining of jets and the cascading process of the meshed one marches more rapidly than that of the normal jet. The wall effects appear in the downstream of about 0.85 H to the impinging wall for every case of wall positions in both nozzles.

• 해양환경안전학회:학술대회논문집
• /
• 해양환경안전학회 2009년도 춘계학술발표회
• /
• pp.87-88
• /
• 2009

증발식 담수화 설비에서 증발기로 유입되는 유동의 속도특성은 플래시현상에 중요한 영향을 미친다. 이 연구에서는 벽면제트류가 유입되는 충돌수분류영역과 배플후류영역의 유동 속도에 배플의 높이가 미치는 효과에 관해 PIV계측을 적용해 실험적으로 고찰하였다.

• 대한기계학회논문집B
• /
• 제20권9호
• /
• pp.2991-3006
• /
• 1996

An experimental study of jet flow and heat transfer has been carried out for the jet impingement cooling on a semi-circular concave surface. For the jet impingement on the concave surface, three different regions-free jet region, stagnation region, and wall jet flow region-exist, and the distributions of mean velocity and fluctuating velocity for each region have been measured by Laser Doppler Velocimeter. Of particular interests are the effects of jet Reynolds number, the distance between the nozzle exit and cooling surface apex, and the distance from the stagnation point in the circumferential direction. The resulting characteristics of heat transfer at the stagnation point and the variation of heat transfer along the circumferential direction including the existence of secondary peak have been explained in conjunction with measured impinge jet flow.

• 대한기계학회논문집
• /
• 제15권1호
• /
• pp.323-327
• /
• 1991

본 연구에서는 로켓노즐로 부터 분출되는 고온의 초음속제트가 45˚로 경사진 평판으로 분사되는 경우의 열전달을 측정하였다.고온의 제트가 충돌하는 평판표면 의 고온과 열유속을 측정하는 것이 거의 불가능하므로, 국소적열전달은 국소적 준 1차 원 열전도모형을 평판표면 아래에서 측정한 온도자료에 적용하여 구하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권1호
• /
• pp.52-66
• /
• 1998

An experimental study on the flow characteristics was performed for a two-dimensional turbulent wall attaching offset jet at different oblique angles to a surface. The flow characteristics were investigated by using a split film probe with the modified Stock's calibration method. The jet mean velocity, turbulent intensity, wall static pressure coefficient profiles, and time-averaged reattachment point were measured at the Reynolds number Re (based on the nozzle width, D) ranging from 17700 to 53200, the offset ratio H/D from 2.5 to 10, and the inclined angle .alpha. from 0.deg. C to 40.deg. C. The Correlations between the maximum pressure position, minimum pressure position, and reattachment point and offset ratios, and inclined angles are presented.

• 대한기계학회논문집
• /
• 제16권2호
• /
• pp.302-312
• /
• 1992

Three dimensional velocity measurements of a 35.deg. inclined jet issuing into turbulent boundary layer on both concave and convex surfaces have been conducted. To investigate solely the effect of each curvature on the flow field, streamwise pressure variations are minimized by adjusting the shape of the opposite wall in the curved region. From the measured velocity components, streamwise mean vorticities are calculated to determine jet-crossflow interface. The results on convex surface show that the injected jet is separated from the wall and the bound vortex maintains its structure far downstream. On concave surface, the secondary flow in the jet cross-sections are enhanced and in some downstream region from the jet exit, the flow on the concave surface has been developed to Taylor-Gortler vortices

• 대한기계학회논문집
• /
• 제18권12호
• /
• pp.3386-3394
• /
• 1994

An experimental study has been performed on the flow over a rotating disk, where the diameter of the disk is 500 mm and the maximum vertical deviation of the upper surface is $50 \mu{m}$ for the whole range of the angular velocity up to 3400 rpm. The flow visualization experiment for the wall jet flow induced by impinging circular jet is carried out using schlieren system and measurements are made by 3-hole and 5-hole pitot tubes. Schlieren photographs show that as the rotating speed increases the wall jet flow becomes more stable and the size of the largest eddies becomes smaller. Measurements for impinging jet flow on the stationary disk verify the accuracy of the present experiment, and those for free rotating disk flow display the existence of transition region from laminar to turbulent flows. Measurements for impinging jet flow on the rotating disk exhibit the interaction between the wall jet and the viscous pumping effect, which explains the decay in size of turbulent eddies illustrated by the schlieren photographs.