• 한국분무공학회지
• /
• 제2권1호
• /
• pp.36-45
• /
• 1997

A spray-wall impingement model for fuel sprays is proposed and implemented as a module into the KIVA-POSTECH code. The model is based on the single droplet experiments. The droplet behaviors after impingement are determined from experimental correlations. Different behaviors of impinged droplets depend on the wall temperature and the critical temperature of the fuel. Fuel film formation is taken into account so that the model can be applicable to any wall temperature and injection conditions. Computational results on a normal and on inclined wall are in good agreement for the spray shape and penetration. More validation against experiments and development of the heat transfer model are needed for further improvement.

• 한국분무공학회지
• /
• 제13권4호
• /
• pp.173-179
• /
• 2008

The current machinery and tools of secondary channel of the nuclear power plants were produced in the carbon-steel and low-alloy steel. What produced with the carbon-steel occurs wall thinning effect from flow accelerated corrosion by the fluid flow at high temperature, high pressure. Several nuclear power plants in Korea have experienced wall thinning damage in the area around the impingement baffle-installed. Wall thinning by flow accelerated corrosion occurs piping system, the heat exchanger, steam condenser and feedwater heaters etc,. Feedwater heaters of many nuclear power plants have recently experienced sever wall thinning damage, which will increase as operating time progress. This study describes the comparisons between the numerical results using the FLUENT code and experimental data of down scale model.

• 한국분무공학회지
• /
• 제22권3호
• /
• pp.129-136
• /
• 2017

Effects of collision angle on heat transfer characteristics of a liquid droplet impinging on a heated wall above the Leidenfrost point temperature were experimentally investigated. The heated wall and droplet temperatures were $506^{\circ}C$ and $100^{\circ}C$, respectively, and the impact angle varied from $20^{\circ}$ to $90^{\circ}$ while the normal collision velocity was constant at 0.27 m/s. The droplet collision behaviors and the surface temperature distribution were measured using synchronized high-speed video and infrared cameras. The major physical parameters influencing upon droplet-wall collision heat transfer, such as residence time, wall heat flux, effective heat transfer area, heat transfer amount, were analyzed. It was found at the constant normal collision velocity that the residence time, wall heat flux and effective heat transfer area were hardly not changed, resulting in the almost constant heat transfer amount.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2012년도 제44회 KOSCO SYMPOSIUM 초록집
• /
• pp.245-246
• /
• 2012

The possibility that self-ignition can be generated near an obstacle is high in practical applications such as a hydrogen car. In this paper, experimental investigations were suggested to understand the effects of a wall on self-ignition phenomena through high-speed images. The results showed that the existence of a wall could not change the ignition phenomena itself irrespective of wall height and burst pressure. However, when a strong flame was induced in the tube, a wall could promote the flame stabilization.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2631-2636
• /
• 2008

The most components and piping of the secondary side of domestic nuclear power plants were manufactured carbon-steel and low-alloy steel. Flow accelerated corrosion leads to wall thinning (metal loss) of carbon steel components and piping exposed to the flowing water or wet steam of high temperature, pressure, and velocity. The feedwater heaters of many nuclear power plants have recently experienced sever wall thinning damage, which increases as operating time progress. Several nuclear power plants in Korea have also experienced wall thinning damage in the shell wall around the impingement baffle. This paper describes the comparisons between the numerical analysis results using the FLUENT code and the experimental results based on down-scaled experimental facility. The experiments were performed based on several types of impingement baffle plates which are installed in low pressure feedwater heater.

• 대한기계학회논문집B
• /
• 제25권8호
• /
• pp.1013-1020
• /
• 2001

This paper addresses to the area where the extended collision model is applied. In order to find the optimum shape of wall sprays, the extended model is applied to the nearest cells of just over the impaction wall, spray core or over all. The droplet distribution, wall spray radii, heights and gas flows are shown in all the cases. Those results show that the best spray shape represents in the case applying the extended model just on the impinging wall.

• 에너지공학
• /
• 제21권2호
• /
• pp.187-193
• /
• 2012

본 연구의 목적은 벽면제트영역의 열전달증진을 위해 직삼각형 로드 및 정사각형 로드를 충돌판앞에 배열한 후 로드와 충돌판 사이의 간극을 변화시키면서 열유동 특성을 실험적으로 검토한 것이다. 열전달증진율은 천이영역인 H/B=10보다는 포텐셜코어영역인 H/B=2에서 더 높게 나타났다. 본 실험범위에서 최대 열전달증진율은 직삼각형 로드를 설치할 때(H/B=2, C=1mm인 조건) 로드가 없는 평판과 비교하면 평균 약 46% 높게 나타났다. 그리고 직삼각형 로드와 정사각형 로드의 열전달증진율을 비교하면 간극 변화와 관계없이 직삼각형 로드가 정사각형 로드보다 평균 약 3~8% 정도 높게 나타났다.

• 대한기계학회논문집B
• /
• 제23권1호
• /
• pp.43-57
• /
• 1999

The fluid flow and heat transfer in a thin liquid film are investigated numerically. The flow Is assumed to be two-dimensional laminar and surface tension is considered. The most important characteristics of this flow is the existence of a hydraulic jump through which the flow undergoes very sharp and discontinuous change. Arbitrary Lagrangian-Eulerian(ALE) method is used to describe moving free boundary and a modified SIMPLE algorithm based on streamline upwind Petrov-Galerkin(SUPG) finite element method is used for time marching iterative solution. The numerical results obtained by solving unsteady full Navier-Stokes equations are presented for planar and radial flows subject to constant wall temperature or constant wall heat flux, and compared with available experimental data. It Is discussed systematically how the inlet Reynolds and Froude numbers and surface tension affect the formation of a hydraulic jump. In particular, the effect of temperature dependent fluid properties is also discussed.

• International Journal of Automotive Technology
• /
• 제6권5호
• /
• pp.437-444
• /
• 2005

Unburned hydrocarbon (UBHC) emissions from gasoline engines remain a primary engineering research and development concern due to stricter emission regulations. Gasoline engines produce more UBHC emissions during cold start and warm-up than during any other stage of operation, because of insufficient fuel-air mixing, particularly in view of the additional fuel enrichment used for early starting. Impingement of fuel droplets on the cylinder wall is a major source of UBHC and a concern for oil dilution. This paper describes an experimental study that was carried out to investigate the distribution and 'footprint' of fuel droplets impinging on the cylinder wall during the intake stroke under engine starting conditions. Injectors having different targeting and atomization characteristics were used in a 4-Valve engine with optical access to the intake port and combustion chamber. The spray and targeting performance were characterized using high-speed visualization and Phase Doppler Interferometry techniques. The fuel droplets impinging on the port, cylinder wall and piston top were characterized using a color imaging technique during simulated engine start-up from room temperature. Highly absorbent filter paper was placed around the circumference of the cylinder liner and on the piston top to collect fuel droplets during the intake strokes. A small amount of colored dye, which dissolves completely in gasoline, was used as the tracer. Color density on the paper, which is correlated with the amount of fuel deposited and its distribution on the cylinder wall, was measured using image analysis. The results show that by comparing the locations of the wetted footprints and their color intensities, the influence of fuel injection and engine conditions can be qualitatively and quantitatively examined. Fast FID measurements of UBHC were also performed on the engine for correlation to the mixture formation results.

• 항공우주기술
• /
• 제4권2호
• /
• pp.135-141
• /
• 2005

본 논문에서는 와류형 및 충돌형 분사기를 가진 액체로켓엔진용 축소형 연소기의 기본 설계 및 상세설계에 대해 기술하였다. 와류분사기는 내부에 액체산소 외부에 케로신을 공급하여 노즐 내부 또는 외부에서 혼합하는 구조를 가지고 있다. 축소형 연소기는 분사기 헤드, 삭마 냉각방식의 내열재 연소실 그리고 물냉각 노즐로 구성되어 있다. 분사기 헤드는 18개의 주 분사기, 하나의 중앙 분사기, 연료 메니폴드, 산화제 매니폴드 그리고 추진제 분배기 등으로 구성되어 있다.