• Nuclear Engineering and Technology
• /
• 제40권4호
• /
• pp.305-310
• /
• 2008

Based on a composition of 99.4 wt% AISI 316L stainless steel, 0.3wt% Ti and 0.3 wt% $Y_2O_3$, an austenitic ODS steel was fabricated by a process of mechanical alloying, hot isostatic pressing and rolling. Fine oxide particles were observed in the matrix, and their chemical formulations were determined to be $Y_2Si_2O_7$ and TiO. Heat treatment of the cold-rolled sample at $1200^{\circ}C$ induced an isotropic tensile behavior at room temperature and at $700^{\circ}C$. This result would be mainly attributed to the equiaxed grains that form as a result of the heat treatment for recrystallization.

• Nuclear Engineering and Technology
• /
• 제40권6호
• /
• pp.505-510
• /
• 2008

The correlation between the tensile strength and corrosion behavior of Zr-1.0wt%Nb alloy heat treated at $480^{\circ}C$ for up to 32 hours was evaluated. The tensile strength at $400^{\circ}C$ was continuously reduced with an increasing heat treatment time, mainly due to a grain growth and a decreased area fraction of the precipitates. However, the corrosion resistance in an aqueous ammonia solution at $360^{\circ}C$ was enhanced, mainly due to the formation of $\beta$-Nb precipitates. It is thus concluded that a longer heat treatment time provides a better corrosion resistance while degrading the tensile strength.

• Elastomers and Composites
• /
• 제48권3호
• /
• pp.195-200
• /
• 2013

본 연구의 주요 목적은 신발 겉창 재료로 사용하기 위하여 열가소성 폴리우레탄 (TPU)의 내마모성과 습윤시의 내슬립성을 에틸렌-프로필렌-디엔 고무 (EPDM) 또는 폴리부타디엔 고무 (BR)를 블렌드하여 향상시키는 것이다. 10 wt%의 EPDM 또는 BR이 TPU에 투입되었을 때 TPU/EPDM과 TPU/BR 블렌드는 TPU보다 우수한 NBS 내마모도, 인장 물성 그리고 습윤 내슬립성을 보였다. 10 wt% 이상 투입될 때는 내마모도와 인장 물성 모두 감소하였다. 10 wt% 투입시의 내마모도와 인장물성 상승은 TPU의 상분리도 증가에 기인하는 것으로 보인다.

• 멤브레인
• /
• 제19권4호
• /
• pp.324-332
• /
• 2009

본 연구는 정밀여과용 Chlorinated Polyvinyl Chloride (CPVC) 평막의 화학약품 수용액 내에서 경과시간에 따른 내화학성을 측정하기 위하여 실시하였다. 화학약품으로는 막 세정에 주로 사용되는 유효염소 0.5 wt% NaClO 수용액과 산성인 HCl 1 wt%, pH 4 수용액 그리고 알카리인 NaOH 4 wt%, pH 10 수용액을 사용하였다. 이상의 수용액중에 CPVC 분리막을 1일, 3, 5, 10일 동안 5, 25, $50^{\circ}C$에서 침지시킨 후, 각각의 인장강도와 파단시 신장율을 측정하여 내구성을 평가하였다. 막 세정시 주로 사용되는 유효염소 0.5 wt% NaClO 수용액의 경우 $5^{\circ}C$ 조건에서는 인장강도 변화는 5% 이내이지만 25, $50^{\circ}C$에서는 17%까지 감소하였다. CPVC 분리막의 내화학성은 산성인 HCl 1 wt%와 pH 4 수용액에서 우수하였으나 NaOH 4 wt% 수용액에 대해서 가장 취약한 것으로 나타났다.

• 대한금속재료학회지
• /
• 제46권12호
• /
• pp.788-799
• /
• 2008

This study is concerned with the effects of Mo, Cr, and V addition on tensile and Charpy impact properties of API X80 linepipe steels. Four kinds of steels were processed by varying Mo, Cr, and V additions, and their microstructures and tensile and Charpy impact properties were investigated. Since the addition of Mo and V promoted to form fine acicular ferrite and granular bainite, while prohibiting the coarsening of granular bainite, it increased the strength and upper shelf energy, and decreased the energy transition temperature. The Cr addition promoted the formation of coarse granular bainite and secondary phases such as martensite-austenite constituents, thereby leading to the increased effective grain size, energy transition temperature, and strength and to the decreased upper shelf energy. The steel containing 0.3wt.% Mo and 0.06wt.% V without Cr had the highest upper shelf energy and the lowest energy transition temperature because its microstructure was composed of fine acicular ferrite and granular bainite, together with a small amount of hard secondary phases, while its tensile properties maintained excellent.

• 한국세라믹학회지
• /
• 제42권10호
• /
• pp.654-659
• /
• 2005

The ceramic paper, which could adsorb VOC's effectively, was made by paper-making method with zeolite and ceramic fiber as main constituents. By this experiment, the optimal composition of the slurry for the ceramic paper formation was established. SEM observation showed that zeolite powder was uniformly dispersed and adhered to the paper by applying inorganic binder. The two type zeolites content in the ceramic paper was 26 wt$\%$ and its BET surface area was 131 $m^{2}$/g. The thickness and the basis weight of the ceramic paper were 0.2 mm and 130 g/$m^{2}$ respectively, and it had sufficient tensile characteristics to withstand tensile stress without tearing during corrugation. The total inorganic content of the paper was 78 wt$ \% $ and organic content was 22 wt$\%$. The equilibrium loading amount of toluene at the toluene at the toluene partial pressure of 0.2 mmHg was 3.2 wt$\%$.

• 한국주조공학회지
• /
• 제26권6호
• /
• pp.258-266
• /
• 2006

The purpose of this study was to investigate the effects of silicon and nickel additions that influenced the impact and tensile properties of heavy section as-cast ductile irons for wind mill. Based on the results of the metallographic analysis and the mechanical testing on the 2.0 wt.%Si (LS group) and 2.4 wt.%Si (HS group) ductile irons, which contains 0.0, 0.3, 0.6 and 0.9 wt.%Ni, respectively, the following conclusions could be obtained. The nickel additions increased the tensile properties, the microhardness of pearlite, and the pearlite fraction of matrix for the specimen with the same silicon content. The mechanical properties of LS group specimen were in the range of the specification for the ductile iron wind mill castings. The LS group specimens showed higher absorbed impact energy at room temperature and $-20^{\circ}C$ than that of the HS group specimens. However, the absorbed impact energy at $-20^{\circ}C$ for the HS group specimens was observed to be sharply decreased under 10 J by addition of the nickel.

• Steel and Composite Structures
• /
• 제38권2호
• /
• pp.177-187
• /
• 2021

The effect of nanoparticle volume fraction on the elastic properties of a polymer-based nanocomposite was experimentally investigated and the obtained results were compared with various existing theoretical models. The nanocomposite was consisted of high density polyethylene (HDPE) as polymeric matrix and 0, 0.5, 1 and 1.5 wt.% multi walled carbon nanotubes (MWCNTs) prepared using twin screw extruder and injection molding technique. Nanocomposite samples were molded in injection apparatus according to ASTM-D638 standard. Therefore, in addition to morphological investigations of the samples, tensile tests at ambient temperature were performed on each sample and stress-strain plots, elastic moduli, Poisson's ratios, and strain energies of volume units were extracted from primary strain test results. Tensile test results demonstrated that 1 wt.% nanoparticles presented the best reinforcement behavior in HDPE-MWCNT nanocomposites. Due to the agglomeration of nanoparticles at above 1 wt.%, Young's modulus, yielding stress, fracture stress, and fracture energy were decreased and Poisson's ratio and failure strain were increased.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2007년 추계학술발표대회 개요집
• /
• pp.322-324
• /
• 2007

Nd:YAG laser welding of AZ31B-H24 magnesium alloy was carried out using AZ61 filler wire(Mg-6wt%Al-1wt%Zn). Microstructure and mechanical properties of welded joint were examined by optical microscopy, scanning electronic microscopy(SEM), energy dispersive spectroscopy(EDS), electron probe micro analyzer(EPMA) and victors hardness, tensile test at the room and elevated temperature. Test results indicate that the specimens welded with AZ61 filler wire have better tensile strength, elongation and victors hardness at room temperature than those of welded without filler wire. However tensile strength are similar but elongation are quite different at elevated temperature.

• Nuclear Engineering and Technology
• /
• 제31권6호
• /
• pp.561-571
• /
• 1999

Microstructure and mechanical properties of five Cr-Mo steels for nuclear industry applications have been investigated. Transmission electron microscopy, energy dispersive spectrometer, differential scanning calorimeter, hardness, tensile, and impact test were used to evaluate the Cr and W effect on the microstructure and mechanical properties. Microstructures of Cr-Mo steels after tempering are classified into three types : bainitic 2.25Cr-lMo steel, martensitic Mod.9Cr-lMo, HT9M, and HT9W steels, and dual phase HT9 steel. The majority of the precipitates were found to be M$_{23}$C$_{6}$ carbides. As minor phases, fine needle-like V(C,N), spherical NbC, fine needle-like Cr-rich Cr$_2$N, and Cr-rich M$_{7}$C$_3$were also found. Addition of 2wt.% W in Cr-Mo steels retarded the formation of subgrain and dissolution of Cr$_2$N precipitates. Hardness and ultimate tensile strength increased with increasing Cr content. Though Cr content of HT9W steel was lower than that of HT9 steel, the hardness of HT9W was higher due to the higher W content. W added HT9W steel had the highest ultimate tensile strength above $600^{\circ}C$. But impact toughness of W added steel (HT9W) and high Cr steel (HT9) was low.w.w.