• Journal of Powder Materials
• /
• v.6 no.1
• /
• pp.36-41
• /
• 1999

The present work has attempted to investigate the dependence of Cu infiltration kinetics on in-situ structure modification of W powder skeleton in W-Cu system. In-situ structure modification of W skeleton by addition of 0.3wt%Ni-P eutectic alloy was designed to proceed during heat-up of the W compact for Cu infiltration process. It was found that the Ni-P added W skeleton underwent remarkable stucture change only during heating-up. its structure was composed of large necks of W particles above 0.5 in the ratio of neck to particle size and smooth pore channels. The infiltration experiment showed that the infiltration kinetics for the W-Ni-P followed well the linear relationship of h vs. $t^{1/2}$ the rate constant K of which was in good agreement with the theoretical value. On the other hand, in case of the pure W skeleton a lower K value by 20% than the theoretical one was obatined. Such discrepancy is discussed in terms of skeleton structure induced infiltration mechanics.

• Membrane and Water Treatment
• /
• v.4 no.2
• /
• pp.109-126
• /
• 2013

Surface modification by low-pressure ammonia ($NH_3$) plasma on commercial thin-film composite (TFC) membranes was investigated in this study. Surface hydrophilicity, total surface free energy, ion exchange capacity (IEC) and zeta (${\zeta}$)-potentials were determined for the TFC membranes. Qualitative and quantitative analyses of the membrane surface chemistry were conducted by attenuated total reflectance Fourier transform infrared (ATR FT-IR) spectroscopy. Results showed that the $NH_3$ plasma treatment increased the surface hydrophilicity, in particular at a plasma treatment time longer than 5 min at 50 W of plasma power. Total surface free energy was influenced by the basic polar components introduced by the $NH_3$ plasma, and isoelectric point (IEP) was shifted to higher pH region after the modification. A ten (10) min $NH_3$ plasma treatment at 90 W was found to be adequate for the TFC membrane modification, resulting in a membrane with better characteristics than the TFC membranes without the modification for water treatment. The thin-film chemistry (i.e., fully-aromatic and semi-aromatic nature in the interfacial polymerization) influenced the initial stage of plasma modification.

• Textile Coloration and Finishing
• /
• v.4 no.4
• /
• pp.110-116
• /
• 1992

For the modification of PET surface, Perfluoropropene and Methyl alcohol were LT-plasma polymerized on the PET fabrics as thin films by means of 13.56 MHz radio frequency generator. The surface properties of PET fabrics were modified from hydrophobic to hydrophilic by application of the postplasma reaction of thin films. The evidence of the modification was identified by observation of the presence of hydroxy group in IR spectrum and the evaluation of degree of hydrophilicity was performed by measuring frictional static voltage of PET fabric with cotton fabric. For the case of modification by PFP, the result performed at the condition of 25 W, 70 m torr has shown to be effective, and for MeOH, result performed at the condition of 25 W, 100 m torr effective. The effect of hydrophilic surface modification of MeOH plasma polymer was superior to that of PFP-plasma polymer.

• The Research Journal of the Costume Culture
• /
• v.31 no.6
• /
• pp.756-775
• /
• 2023

This study was aimed at examining the characteristics of women's blue denim on the basis of design elements to provide fundamental data for fashion majors and fashion designers. Seven design elements were selected from previous studies to compare them with the following characteristics of blue denim: color (washing, dyeing), ornamentation (trimming, detailing, painting, and printing), and form modification, tearing, and ripping). Data from 1,520 photographs of the 2019 S/S to the 2023-24 F/W collections were collected through overlapping checks. The data were then subjected to frequency analysis using the Statistical Package for the Social Sciences (version 26). The results are as follows: The most frequent design method used in producing the denim items in our sample was washing, followed by modification, tearing, and ripping and detailing. The greatest change in denim design occurred in 2023, and more design element changes were observed in the F/W season than in the S/S season. Washing was used four times or more frequently than dyeing, while detailing was employed approximately 2 times more often than trimming. With respect to form, the most common approach was modification, followed by tearing and ripping.

• The Journal of the Korean dental association
• /
• v.31 no.11 s.294
• /
• pp.788-790
• /
• 1993

• International Journal of Automotive Technology
• /
• v.8 no.2
• /
• pp.225-232
• /
• 2007

A tooth profile modification for loaded gears is used to avoid a tooth impact. Since a tooth profile error causes amplification of the cumbersome whine noise in automotive gear transmissions, an optimal quantity of tooth profile modifications must be obtained for good performance in the vibration sense. In this paper, a tooth profile modification curve considering profile manufacturing errors and elastic deformation of the gear tooth is formulated; in addition, transmission errors of the gear system with modified teeth are verified. The equivalent excitation due to transmission errors is formulated. For experimental evaluation of the transmission error, the transmission error for a simple gear system was measured by two rotational laser vibrometers. Finally, we perform a comparative analysis between the calculated and measured responses to the excitations due to the transmission error to verify the practicability of the application to automotive transmissions.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.321-324
• /
• 2008

The increasing interest in the surface modification by the laser cladding technology in the material processing is placing stringent demands on the manufacturing techniques and performance requirements, and the manufacture employs the high quality and efficiency laser cladding technology. This paper covers recent technical trends of laser cladding technology including the COMPENDEX DB analysis.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.358-361
• /
• 2009

The increasing interest in the surface modification technology by the plasma transferred arc overlaying process in the material processing is placing stringent demands on the manufacturing techniques and performance requirements, and the manufacture employs the high quality and efficiency plasma transferred arc overlaying technology. This paper covers recent technical trends of plasma transferred arc overlaying technology including the COMPENDEX DB analysis.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2000.09a
• /
• pp.512-513
• /
• 2000

• Journal of the Korean Ceramic Society
• /
• v.43 no.1 s.284
• /
• pp.38-41
• /
• 2006

Surface of PC (Polycarbonate) and PES (Polyethersulphone) treated by plasma modification with rf power from 50 W to 200 W substrates in Ar (3 sccm), $O_2$ (12 sccm) atmosphere. From the results of modified substrates in XPS (X-ray Photoelectron Spectroscopy), the ratio of oxide containing bond increased with rf power. As the rf power was 200 W, the contact angle was the lowest value of 14.09 degree. And the datum from AFM (Atomic Force Microscopy), rms roughness value of PES and PC substrates increased with rf power. We could deposit $Ta_2O_5$ with good adhesion on plasma treated PES and PC substrates using by in-situ rf magnetron sputter.