• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.600-603
• /
• 2003

Energy spectrum modulation of X-ray source in digital mammography has been studied. In this study, we calculated various filtered spectra using the scattering data. Primary spectra were generated by Molybdenum (Mo) and Tungsten (W) targets. The materials of added filters are Molybdenum and Rhodium (Rh) for 40 kVp Mo. primary spectrum, the amounts of photons over whole energy ranges are attenuated to 0.43 with 0.03 mm Mo filter and 0.38 with 0.06 mm Mo filter while the photons of energy ranged from 17 keV to 20 keV. The photons of low energy ranged below 17 keV are considerably attenuated. This effect brings out reducing the scattered radiation and dose to the patient, and enhancing subject contrast in the image. The results show that filtered spectra are not seriously affected by X-ray tube loadability. Because the energy range from 17 keV to 20 keV is directly transmitted although low and high energies are mainly filtered.

• Journal of the Korean Society for Heat Treatment
• /
• v.26 no.5
• /
• pp.241-247
• /
• 2013

Hardenability and mechanical properties of boron-bearing steels containing C, Mo and Cr were investigated in this study. Using quench dilatometer, the steel specimens were cooled down to room temperature at different cooling rates to construct continuous cooling transformation diagrams and then the transformation products from austenite were examined. A critical cooling rate was introduced as an index to quantitatively evaluate the hardenability. The C addition to boron-bearing steels did not significantly affect hardenability compared to boron-free steels although it increases the hardenability. With the same content, the Mo addition largely increased the hardenability of boron-bearing steels than the Cr addition because it decreased both the transformation start and finish temperatures at low cooling rates. In particular, the Mo addition completely suppressed the formation of eutectoid ferrite even at the slow cooling rate of $0.2^{\circ}C/s$, whereas the Cr addition nearly suppressed it at the cooling rates above $3^{\circ}C/s$.

• Journal of the Korean Ceramic Society
• /
• v.54 no.3
• /
• pp.200-204
• /
• 2017

Molybdenum (Mo), an electrode material of alkali metal thermal-to-electric converters (AMTEC), facilitates grain growth behavior and forms Mo-Na-O compounds at high operating temperatures, resulting in reduced performance and shortened lifetime of the cell. Mo/TiN composite materials have been developed to provide a solution for such issues. Mo is a metal that possesses excellent electrical properties, and TiN is a ceramic compound with high-temperature durability and catalytic activity. In this study, a dip-coating process with an organic solvent-based slurry was used as an optimal coating method to achieve homogeneity and stability of the electrodes. Cell performance was evaluated under various conditions such as the number of coatings, ranging from 1 to 3 times, and heat treatment temperatures of $800-1100^{\circ}C$. The results confirmed that the cell yielded a maximum power of 9.99 W for the sample coated 3 times and heat-treated at $900^{\circ}C$.

• Bulletin of the Korean Chemical Society
• /
• v.24 no.6
• /
• pp.832-836
• /
• 2003

To extend the knowledge of triple bonding between group 6 transition metal and heavier group 14 elements, the structural and bonding aspects of ($η^5-C_5H_5$)$(CO)_2$M≡ER (M = Cr, Mo, W; E = Si, Ge, Sn, Pb) are investigated by hybrid density functional calculations at the B3PW91 level. Substituent effects are also investigated with R = H, Me, $SiH_3$, Ph, $C_6H_3-2,6-Ph_2$, $C_6H_3-2,6-(C_6H_2-2,4,6-Me_3)_2$, and $C_6H_3-2,6-(C_6H_2-2,4,6- iPr_3)_2$.

• Journal of the Korean Chemical Society
• /
• v.44 no.3
• /
• pp.194-199
• /
• 2000

The chemical behavior for Mo(0) and W(0) complexes, [M(CO)$_2$(PPh$_3$)$_4$] (M=Mo and W),has been investigated by UV-vis spectroscopic, magnetic, and electrochemical methods. Three absorption bands are observed in the UV-spectra. The crystal-field-splitti ng energy, spin-pairing energy, and bond strengths were deduced from the spectra. The metal d electrons in both complexes seemed to be delocalized in low-spin state.Metal ligand correlation appeared to strongly depend on bond strengths and diamagnetic properties. In electrochemical processes, both complexes exhibit an irreversible reduction wave.

• Korean Journal of Materials Research
• /
• v.8 no.1
• /
• pp.64-70
• /
• 1998

자동차의 엔진밸브 스프링으로 사용되는 Si-Cr 스프링강의 영구 변형 저항성과 내피로성이 우수한 고강도강을 개발하기 위하여 탄소함량을 증대시키고 Mo, V, W와 같은 합금원소를 기존의 SAE 9254 스프링강에 첨가하여 개발강을 제조했다. SEM및 EDX가 부착된 TEM을 이용하여 미세조직을 관찰했고, 크립시험 및 피로시험기를 이용하여 스프림의 영구 변형 저항성 및 스프링의 내피로성을 조사했다. 실험결과, 개발강은 피로 특성치는 기존강과 동등 수준이면서 인장강도가 기존강의 것보다 10%가 더높은 2100MPa 급의 고강도를 나타내었으며 또한 영구 변형 저항성도 현저하게 개선되었는데 이는 W, Mo의 첨가로 인해 템퍼링시에 세멘타이트의 성장이 억제되어서 세멘타이트의 석출물이 미세하게 되었기 때문이다.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1657-1659
• /
• 1996

The objective of this study is to provide a life prediction of isothermal fatigue using strain partitioning of high temp. steel for power plants. The experimental system was composed of Instron 8501, induction heating system, extensometer and pyrometer with hydraulic power system

• Economic and Environmental Geology
• /
• v.29 no.3
• /
• pp.247-256
• /
• 1996

Mineral commodities of metallic ore deposits related to Cretaceous granitoids in the Taebaegsan basin are distinguishable by rock types, diffferenciation index (D.I.) and chemical compositions. Deposits of Fe-Cu are related to granodiorite-quartz monzonite, those of Pb-Zn and W-Mo to granite-granodiorite and granite respectively. The ranges of D.I. of the granitoids are 39~71 for Fe-Cu deposits, 68~81 for Pb-Zn deposits, 78~89 for W-Mo deposits and 91~94 for Mn deposits. Major oxides of $K_2O$, CaO, MgO, FeO and $TiO_2$ and some trace elements and Rb/K, Sr/Ca and Cu/Fe also show distinguishable differences among the Cretaceous granitoids related to various mineral commodities of the ore depsits.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.350-353
• /
• 2005

It is a feature of primary importance for a backing material for circular saw blades having teeth which are tipped with cermet, that the steel has not a too high hardenability in order that the backing material shall not be completely hardened through brazing, welding or grinding, etc. in connection with the finishing operation in the manufacturing of circular saw blade. It is believed that V-(2Mo+W) added steel from this point of view had best conditions. Using V-(2Mo+W) added backing steel, the tool failure can be effectively prevented due to superior damping performance.

• Journal of Welding and Joining
• /
• v.20 no.6
• /
• pp.30-30
• /
• 2002

It has been reported that the creep characteristics on weldment which is composed of weld metal(W.M), fusion line(F.L), heat-affected zone(HAZ), and base meta(B.M) could be unpredictably changed in severe service conditions such as high temperature and high pressure. However, the studies done on creep damage in power plant components have been mostly conducted on B.M and not the creep properties of the localized microstructures in weldment have been thoroughly investigated yet. In this paper, it is investigated the creep characteristics for three microstructures like coarse-grain HAZ(CGHAZ), W.M, and B.M in X20CrMoV121 steel weldment by the small punch-creep-(SP-Creep) test using miniaturized specimen(l0×10×0.5mm). The W.M microstructure possesses the higher creep resistance and shows lower creep strain rate than the B.M and CGHAZ. In the lower creep load the highest creep strain rate is exhibited in CGHAZ, whereas in the higher creep load the B.M represents the high creep strain rate. The power law correlation for all microstructures exists between creep rate and creep load at 600℃. The values of creep load index (n) based on creep strain rate for B.M, CGHAZ, and W.M are 7.54, 4.23, and 5.06, respectively and CGHAZ which shows coarse grains owing to high welding heat has the lowest creep loade index. In all creep loads, the creep life for W.M shows the highest value.