• JSTS:Journal of Semiconductor Technology and Science
• /
• 제3권3호
• /
• pp.114-121
• /
• 2003

Through comparing stress state of TEOS and SiLK-embedded structures, the effect of low-k materials on stress and stress distribution in via-line structures were investigated using three-dimensional finite element analyses. In the case of TEOS-embedded via-line structures, hydrostatic stress was concentrated at the via and the top of the lines, where the void was suspected to nucleate. On the other hand, in the via-line structures integrated with SiLK, large von-Mises stress is maintained at the via, thus deformation of via is expected as the main failure mode. A good correlation between the calculated results and experimentally observed failure modes according to dielectric materials was obtained.

• 한국철도학회논문집
• /
• 제5권3호
• /
• pp.167-173
• /
• 2002

The influence of thermal stress at tread breaking in Korean High Speed Train wheel was investigated using the coupled thermal-mechanical analysis technique. The mechanical load or wheel-rail contract load and braking load were considered during FEM analysis. During the stop braking, the effect of mechanical stress on the combined stress is relatively larger than that of thermal stress in the rim of wheel. However, the effect of thermal stress is relatively larger than that of mechanical stress in the plate of wheel. When 300% of the block force was applied, the maximum von Mises stress of 61.0 MPa was found at the outside plate around 400 mm far away from the wheel center.

• 한국정밀공학회지
• /
• 제24권3호
• /
• pp.76-83
• /
• 2007

The Taguchi method is applied to obtain the optimal design of an automotive pedal arm in consideration of the stiffness test specification. Design parameters are defined to describe shape of the pedal arm. Volume, maximum Von-Mises stress and maximum displacement of the pedal arm are established as the smaller-the-better characteristics. Optimal parameters are determined on the basis of the analyzed level averages of the characteristics.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.395-396
• /
• 2010

• 한국정밀공학회지
• /
• 제23권10호
• /
• pp.121-125
• /
• 2006

In this paper, results are presented by nonlinear finite element simulations in order to analy the interactions between the stent and artery or plaque. Maximum of von Mises stress was calculated in the contacting areas between the stent and the artery. The simulated results show that the distal end of stent, which tilts after expansion, may injure the artery wall. In conclusion, this study may help designing new stents.

• 한국임상수의학회:학술대회논문집
• /
• 한국임상수의학회 2009년도 추계학술대회
• /
• pp.248-248
• /
• 2009

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2001년도 춘계학술대회 논문집
• /
• pp.222-229
• /
• 2001

This paper aims to verify the static strength of a KHST gangway structure including fixed ring and carrying ring according to tile load cases in the defined specification. The structure has been analyzed by the finite element method. Calculation carried out in tile fields of linearity and small deformation. The admissible limit is tile yield strength for the available materials. The analysis results show that Von-Mises stress at some locations of the structure is a little beyond the admissible limit. These results are successfully reflected on the adjusted design.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 춘계학술대회 논문집
• /
• pp.45-50
• /
• 1999

The object of this study is structure analysis of vehicle air compressor. Structure analysis is compose to nodal solution and element solution using ANSYS code. Then analysis is partition to head part, cylinder and piston part of vehicle air compressor. Stress and strain results are satisfy to Von Mises yield criterion.

• Journal of Advanced Marine Engineering and Technology
• /
• 제9권3호
• /
• pp.225-239
• /
• 1985

The beams with a circular hole are often used for constructing structures. The center of the circular hole is normally located in neutral axis and the stress state around the hole due to bending moment is trivial. But the stress level around the hole due to shear force is expected to be significant especially in the case of beams made of shape steels. In this paper, the stress distributions around the circular hole of beams were presented. Using polar coordinates and generallized stress function, the formulas of stress components were derived. The aspects of plastic area propagations based on von Mises yield criteria were also shown graphically. In order to verify the formulas presented in this paper, a beam of I-shape steel with a circular hole was made and the strains around the hole were measured under various loading conditions. The experimental results were proved to coincide fairly well with the calculated values.

• 대한치과보철학회지
• /
• 제43권4호
• /
• pp.544-561
• /
• 2005

Purpose : This study was to assess the loading distributing characteristics of implant systems with internal connection or external connection under vertical and inclined loading using finite element analysis. Materials and methods : Two finite element models were designed according to type of internal connection or external connection The crown for mandibular first molar was made using cemented abutment. Each three-dimensional finite element model was created with the physical properties of the implant and surrounding bone This study simulated loads of 200N at the central fossa in a vertical direction (loading condition A), 200N at the centric cusp tip in a 15$^{\circ}$ inward inclined direction (loading condition B), or 200N at the centric cusp tip in a 30$^{\circ}$ outward inclined direction (loading condition C) respectively. Von Mises stresses were recorded and compared in the supporting bone, fixture, abutment and abutment screw. Results : 1. In comparison with the whole stress or the model 1 and model 2, the stress pattern was shown through th contact of the abutment and the implant fixture in the model 1, while the stress pattern was shown through the abutment screw mainly in the model 2. 2. Without regard to the loading condition, greater stress was taken at the cortical bone, and lower stress was taken at the cancellous bone. The stress taken at the cortical bone was greater at the model 1 than at the model 2, but the stress taken at the cortical bone was much less than the stress taken at the abutment, the implant fixture, and the abutment screw in case of both model 1 and model 2. 3. Without regard to the loading condition, the stress pattern of the abutment was greater at the model 1 than at the model 2. 4. In comparison with the stress distribution of model 1 and model 2, the maximum stress was taken at the abutment in the model 1. while the maximum stress was taken at the abutment screw in the model 2. 5. The magnitude of the maximum stress taken at the supporting bone, the implant fixture, the abutment, and the abutment screw was greater in the order of loading condition A, B and C. Conclusion : The stress distribution pattern of the internal connection system was mostly distributed widely to the lower part along the inner surface of the implant fixture contacting the abutment core through its contact portion because of the intimate contact of the abutment and the implant fixture and so the less stress was taken at the abutment screw, while the abutment screw can be the weakest portion clinically because the greater stress was taken at the abutment screw in case of the external connection system, and therefore the further clinical study about this problem is needed.