• Elastomers and Composites
• /
• 제45권4호
• /
• pp.250-255
• /
• 2010

비뉴톤 점탄성 Maxwell 요소와 탄성 스프링으로 이루어진 3 요소 비뉴톤 모델로부터 응력완화 식을 유도하였다. 이 식을 응력완화 실험 결과에 적용하여 여러 가지 모델 파라메타를 계산하였다. 모델 파라메타로부터 계산한 이론 곡선은 실험적인 응력완화 곡선과 잘 일치하였다. 비선형 점탄성 모델 파라메타로부터 섬유고분자 물질의 홀부피, 미세구조, 점탄성성질, 역학적인 성질 등을 연구하였다. 응력완화 실험은 용매기를 부착한 인장 시험기를 사용하였으며, 시료는 두 종류의 polyacrylonitrile-polyvinylchloride 공중합체와 또 다른 두 종류의 PVC 모노 필라멘트 섬유를 여러 온도의 공기와 물속에서 응력완화 실험을 하였다.

• 대한금속재료학회지
• /
• 제49권11호
• /
• pp.823-830
• /
• 2011

Structural change in an amorphous alloy was measured by applying a load below the global yield stregth at ambient temperatures. It was observed that the magnitude of the apparent structural change occuring in the amorphous alloy is determined by the compatative relationship between the stress-induced disordering process and the thermally-activated relaxation process. Structural disorder was observed to take place even at a stress well below the global yield, and the degree of the disorder was increased abruptly at the earlier stage of loading and saturated with time. In the mean time, unlike the previous belief, the relaxation process was observed to occur even at embient temperatures, and the degree of the relaxation was observed to increase linearly with time. The analytical equation predicting the structural change was proposed.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 추계학술발표대회 개요집
• /
• pp.216-218
• /
• 2003

Most of ferrous b.c.c weld materials may experience martensitic transformation during rapid cooling after welding. And it is well known that volume expansion due to phase transformation could influence in the case of welding of high tensile strength steels on the relaxation of welding residual stress. To apply this effect practically, it is a prerequisite to establish a numerical model which is able to estimate the effect of phase transformation on residual stress relaxation quantitatively. In this study, we investigated the effect of phase transformation on the relaxation of welding residual stress through experiment. And three-dimensional thermal elastic-plastic FEM analysis is conducted to compare the effect of phase transformation on the relaxation of welding residual stress in high strength steels(POSTEN60, POSTEN80) with analytical results which is not considering the effect of phase transformation on residual stress relaxation. According to the results, the extents of welding residual stress relaxation due to phase transformation in the case of welding of POSTEN60, POSTEN80 are 0.85 $\sigma$/$\sigma$$\sub$Y0/, 0.75$\sigma$/$\sigma$$\sub$Y0/, respectively.

• 대한기계학회논문집A
• /
• 제26권11호
• /
• pp.2342-2354
• /
• 2002

The present study has numerically predicted both the flow -induced and thermally-induced residual stresses and birefringence in injection o. injection/compression molded center -gated disks. Analysis system for entire molding process was developed based on an ap propriate physical modeling including a nonlinear viscoelastic fluid model, stress-optical law, a linear viscoelastic solid model, free volume theory for density relaxation phenomena and a photoviscoelasticity and so on. Part I presents physical modeling a nd typical numerical analysis results of residual stresses and birefringence in the injection molded center-gated disk. Thermal residual stress was found to be extensional near the center, compressive near the surface and tend to become toward tensional at the surface. A double-hump profile was obtained across the thickness in birefringence distribution: nonzero birefringence is found to be thermally induced, the outer peak is due to the shear flow and subsequent stress relaxation during the filling stage a nd the inner peak is due to the additional shear flow and stress relaxation during the packing stage. Predicted birefringence including both the flow -induced and thermally-induced one becomes quite similar to the experimental one.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.195-198
• /
• 2003

High temperature deformation and softening behavior of SAF 2507 super duplex stainless steel (SDSS) has been investigated in connection with an FEM analysis of hot forging process. Flow curves at various strain rates and temperatures were determined first from compression tests, and the kinetics of dynamic recrystallization were also formulated through the analysis of load relaxation test results. Applying the dynamic materials and proposed by Prasad et al., it was possible to determine the characteristics of deformation behavior effectively at a given condition of deformation. Constitutive relations and recrystallization kinetics formulated from the test results were then implemented in a commercial FEM code. Flow stress compensation formulated upon the volume fraction of recrystallization and adiabatic heating was found to improve significantly the FEA solutions in predicting the forming load and the distribution of recrystallized volume fraction after forging.

• 소성∙가공
• /
• 제16권3호
• /
• pp.193-200
• /
• 2007

Simulations of the thermally-induced residual stresses and birefringence in freely quenched plates of polycarbonate were performed by using the linear viscoelastic and photoviscoelastic constitutive equations for the mechanical and optical properties, respectively, and the first order rate equation for volume relaxation. The predictions for the birefringence showed good agreement with experimental measurements. However, for initial temperature close to the glass transition temperature, some differences existed around the surface layer. Based on the simulation, the influences of various cooling conditions on the residual stress and birefringence in plates were investigated. The residual stress and birefringence increased with increasing initial temperature, decreasing coolant temperature and increasing heat transfer coefficient of coolants.

• 소성∙가공
• /
• 제12권4호
• /
• pp.308-313
• /
• 2003

High temperature deformation and softening behavior of SAF 2507 super duplex stainless steel (SDSS) has been investigated in connection with an FEM analysis of hot forging process. Flow curves at various strain rates and temperatures were determined first from compression tests, and the kinetics of dynamic recrystallization were also formulated through the analysis of load relaxation test results. Using the dynamic materials theory proposed by Prasad, the deformation behavior was effectively determined for various conditions. Constitutive relations and recrystallization kinetics formulated from the test results were then implemented in a commercial FEM code. The forming load as well as the distribution of recrystallized volume fraction after forging was successfully predicted by means of the flow stress compensation formulated upon the volume fraction of recrystallization and adiabatic heating.

• Journal of Welding and Joining
• /
• 제17권6호
• /
• pp.84-89
• /
• 1999

Most of ferrous b.c.c weld materials may experience martensitic transformation during rapid cooling after welding. It is well known that volume expansion due to the phase transformation could influence on the relaxation of welding residual stress. To apply this effect practically, it is a prerequisite to establish a numerical model which is able to estimate the effect of phase transformation on residual stress relaxation quantitatively. For this purpose, the analysis is carried out in two regions. i.e., heating and cooling, because the variation of material properties following a phase transformation in cooling is different in comparison with the case in heating, even at the same temperature. The variation of material properties following phase transformation is considered by the adjustment of specific heat and thermal expansion coefficient, and the distribution of residual stress in analysis is compared with that of experiment by previous study. consequently, in this study, simplified numerical procedures considering phase transformation, which based on a commercial finite element package was established through comparing with the experimental data of residual stress distribution by other researcher. To consider the phase transformation effect on residual stress relaxation, the transition of mechanical and thermal property such as thermal expansion coefficient and specific heat capacity was found by try and error method in this analysis.

• Bulletin of the Korean Chemical Society
• /
• 제22권11호
• /
• pp.1231-1235
• /
• 2001

Pseudotetragonal ZrO0.75S whose space group is P212121 was synthesized and the cell dimensions were a=5.110(2) $\AA$, b=5.110(7) $\AA$, and c=5.198(8) $\AA.$ The space group P212121 seems to be resulted from lowering the symmetry of cubic ZrOS structure with P213 space group by lattice distortion due to the oxygen defects. In the distorted structure, bond shortening between metal-nonmetal by reduction of cell volume and alternation of Zr-Zr distance were observed. Dielectric constant and loss data of the bulk material in temperature range -170 to 20 $^{\circ}C$ and frequency range 50 Hz to 1 MHz showed that there was dielectric transition at around -70 $^{\circ}C$ originated from the relaxation of Zr-S segment. Comparing with ZrO2 exhibited the dielectirc constants, 9.0 at room temperature, ZrO0.75S showed high dielectric constant, k = 200.2 at 100 kHz. The activation energy of relaxation time due to dielectric relaxation of Zr-S was 0.47 eV (11.3 kcal/mole). According to the impedance spectra, ZrO0.75S showed more parallel circuit character between the resistance and capacitance components at the temperature (-70 $^{\circ}C)$ that the Zr-S dielectric relaxation was observed.

• 한국세라믹학회지
• /
• 제40권3호
• /
• pp.286-292
• /
• 2003

본 연구에서는 나노기술을 이용하여 에너지 감쇄 기능을 활용한 감쇄기 개발에 대한 기초적인 연구를 하였다. 기계 구조물에 사용되는 기존의 유체 감쇄기를 대체할 수 있는 무기재료를 이용한 새로운 감쇄기에 대한 기초연구를 수행하여 감쇄기 설계와 실용화에 적용하고자 하였다. 완충역할을 하는 입자로는 미로구조를 가지는 실리카겔을 사용하였고, 입자에 관련한 작동 유체로는 물을 사용하여 실험적으로 그 효과를 검증하였다. 콜로이드 감쇄기를 구현하기 위해서는 형성된 실리카겔 입자의 표면을 유기 실리콘 매질을 이용한 소수화 코팅 처리를 하였다. 콜로이드 감쇄기의 에너지 감쇄량과 효율을 작동 유체에 대하여 각각 구하여 유효한 감쇄 효과를 입증하여 설계에 반영할 수 있게 되었다. 또한 압축해제에 걸리는 시간을 조사하여 기존의 유압 감쇄기와 비교한 결과 본 논문에서 제안된 감쇄기의 기능이 우수함이 입증되었다.