• Korean Chemical Engineering Research
• /
• v.50 no.1
• /
• pp.155-161
• /
• 2012

A dynamic biofilter model was suggested to integrate the effect of biofilter-medium adsorption capacity on the removal efficiency of volatile organic compound (VOC) contained in waste air. In particular, the suggested biofilter model is composed of four components such as biofilm, gas phase, sorption volume and adsorption phase and is capable of predicting the unsteady behavior of biofilter-operation. The process-lumping model previously suggested was limited in the application for the treatment of waste air since it was derived under the assumption that the adsorbed amount of VOC equilibrated with biofilter-media would be proportional to the concentration of dissolved VOC in the sorption volume of biofilter-media. Therefore a Freundlich adsorption isotherm was integrated into a robust biofilter process-lumping model applicable to a wide range of VOC concentration. The values of model parameters related to biofilter-medium adsorption were obtained from the dynamic adsorption column experiments in the preceding article and literature survey. Furthermore a separate biofilter experiment was conducted to treat waste air containing ethanol and the experimental result was compared with the model predictions with various values of Thiele modulus (${\phi}$). The obtained value of Thiele modulus (${\phi}$) was close to 0.03.

• KSBB Journal
• /
• v.11 no.6
• /
• pp.663-668
• /
• 1996

In the production of recombinant protein using E. coli, phage lysogen system can be usefully applied for simultaneously achieving protein production at high cell concentration and recovery by cell disruption in the same bioreactor. A major drawback of this system is that the intracellular product and complex broth components are mixed together in culture broth and hence purification efficiency is reduced. With the E. coli double-lysogen system, the expanded bed adsorption is very useful because the pretreatment processes in a routine bioseparation process can be done in a single column operation, and therefore may contribute towards lowering the operating cost of overall recovery/purification process. In the operation of EBA, it has been observed that the change in broth feed volume does not influence much the protein recovery in a tested range. The amount of protein adsorption per mL of resin was increased from $3.44{\times}106unit to 5.28{\times}106unit$ by doubling the column length. By two-fold increase of the column diameter, the ratio of protein concentration in eluent to that in feed was increased from 0.8 to 2.1. It is concluded from the present investigation that the increase of column length and diameter is necessary to enhance the protein adsorption amount per volume of resin and protein concentration in the eluent. The development of resins with various physical properties will be necessary for more extensive application of EBA.

• The Korean Journal of Mycology
• /
• v.31 no.3
• /
• pp.200-205
• /
• 2003

The study was carried out on the artificial cultivation of the abalone mushroom, Pleurotus cystidiosus O.K.Miller. The pine sawdust substrates with 20% rise bran were good for mycelial growth and high quantity of P. cystidiosus in the bottle cultivation. Moreover, the proper volume for bottle cultivation was 850 ml and the removal of spawn and surface layer of the medium before pin-heading was more efficient. The yields of P. cystidiosus were higher in sawdust substrates added calcium carbonate than those not added calcium carbonate. The volume of 3 kg polypropylene bag is good for yield and biological efficiency in bag cultivation of P. cystidiosus. Cotton wastes were proper substrates for bag cultivation. In the effect of different cultivation temperature, $28{\pm}2^{\circ}C$ cultivation temperature was good for for primordial formation after inoculation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.5
• /
• pp.940-947
• /
• 2006

A variety of actuators fur an implantable artificial heart have been studied. They, all, however, share the disadvantages of a complicated energy conversion mechanism and of the need to use bearings. A ferrofluidic actuator directly drives magnetic fluids by applying a magnetic field to these fluids; it does not require bearings. In this study, the feasibility of a ferrofluidic actuator for an implantable artificial heart was studied. An way of two Poles of ring solenoids was mounted near the acrylic tube $({\phi}\;7.4mm)$. A rubber sack (volume : $2m{\ell}$ was connected to both ends of the acrylic tube. The sack were encased in a rigid chamber that had inlet and outlet ports. The acrylic tube and the rubber sack were filled with water encased in a rigid chamber magnetic fluid and the iron cylinder were immersed in the water. Two experiment method was conducted. 1) distance between stoppers were 72mm and 2) distance between stoppers were 104mm. A stroke volume was stability and $0.96m{\ell}$ was obtained in the experiment 1 and $1.92m{\ell}$ in the experiment 2. The energy efficiency of Experiment method 2 is about five times than Experiment method 2. A magnetic fluid-driven blood pump could be feasible if the magnetic fluid with high magnetization (3 times yester than the current value) is developed.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.17 no.6
• /
• pp.133-143
• /
• 2018

Roundabouts are generally installed at which traffic and pedestrian volume is relatively small intersections, and hence traffic can flow one direction around a circular island without traffic lights. A number of researches for roundabout signal metering have been processing ways to deal with operation efficiency drops in conditions of unusual traffic and pedestrian volume increases. However, there is still a shortcoming exists in previous operation algorithm does not consider the hidden vehicles between yield lines and detectors and queueing vehicles in circular lanes. These queueing vehicles between them can be cleared by introducing the queue clearance time. The purpose of this research is developing a real time signal metering operation algorithm by considering the vehicle queue clearance time. The results of varying queue clearance time application show that there is a substantial average vehicle delay reduction in VISSIM Com-Interface simulation. When the total number of entering vehicle is 3,200~4,800 vehicle/hour with varying queue clearance time application 21~50 seconds gives average delay reduction per vehicle by 16.1~71.7%.

• Journal of the Korea Institute of Building Construction
• /
• v.21 no.5
• /
• pp.459-468
• /
• 2021

Blocking electromagnetic waves on the exterior walls of buildings effectively reduces the intensity of electromagnetic fields in buildings, which leads to attenuation of electromagnetic disturbances, so there is a great interest in developing technologies. In this study, SiC by-products and graphite generated in the semiconductor field were selected and mixed into mortar after pretreatment such as pulverization to evaluate their physical properties and electromagnetic wave shielding performance. Considering the economic efficiency of each shielding material, only 10% volume of the outermost side of the experiment was mixed with each shielding material to evaluate the shielding performance. The shielding performance was predicted when the experiment was manufactured by mixing the shielding material with the entire volume of the experiment using the shielding effect evaluation formula. The results of the experiment showed that the shielding performance was up to 20 dB when SiC grains were mixed with shielding materials, the shielding performance was up to 18 dB when graphite powder was mixed with shielding materials, and the shielding performance was up to 28 dB when SiC powder was mixed with shielding materials, and the shielding performance was close to 30 dB, which is known to have a shielding rate of 99.9%.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.6D
• /
• pp.931-936
• /
• 2008

Surveying by using terrestrial LiDAR(Light Detection And Ranging) is more rapid than by using total station which enables tunnel section profile surveying to be done in suitable time and minimize centerline error, occurrence of overcut and undercut. Therefore, utilization of terrestrial LiDAR has increased more and more in section profile survey and measurement field Moreover, studies of terrestrial LiDAR for accurate and efficient utilization is now ongoing vigorously. Average end area formula, which was generally used to calculate overcut and undercut, was compared with existing methods such as total station survey and photogrammetry. However, there are no criteria of spacing distance for calculating overcut and undercut through terrestrial LiDAR surveying which can acquire 3D information of whole tunnel. This research performed reverse engineering to decide optimal spacing distance when surveying tunnel section profile by comparing whole tunnel volume and tunnel volume in difference spacing distance. This result was utilized to produce CAD drawing for the test tunnel site where there is no design drawings. In addition to this, efficiency of LiDAR and accuracy of CAD drawing was compared with targetless total station surveying of tunnel section profile. Finally, error analysis of target coordinate's accuracy and incidence angle was done in order to verify the accuracy of terrestrial LiDAR technology.

• Journal of Adhesion and Interface
• /
• v.25 no.2
• /
• pp.69-74
• /
• 2024

Soft actuators can be applied to various fields such as the medical industry and manufacturing industry due to the flexibility and smooth movement resulted from their constituent materials. Stimuli-responsive hydrogels are a class of materials that can show large volume changes due to various surrounding stimuli and thus is suitable as a soft actuator material. However, because the change in volume of the stimuli-responsive hydrogel depends on the rate of temperature change and the rate at which the solvent diffuses into the polymer network, in most typical operating conditions, the response time of the actuator is slow due to inefficient heat transfer and diffusion process. In this study, a conjugated polymer was introduced into polydiethylacrylamide, a thermoresponsive hydrogel, to implement a soft actuator driven by light, and the improvement in response time by the photothermal effect of the conjugated polymer was investigated. It was confirmed that the response time was improved by 41% by the introduction of the conjugated polymer, due to the improvement in heat transfer efficiency. Finally, a soft gripper using the hydrogel with improved response time was fabricated and the response time of the gripper was investigated.

• The Journal of Engineering Geology
• /
• v.31 no.3
• /
• pp.433-445
• /
• 2021

Plasma blasting by high voltage arc discharge were performed in laboratory-scale soil samples to investigate the fluid penetration efficiency. A plasma blasting device with a large-capacity capacitor and columnar soil samples with a diameter of 80 cm and a height of 60 cm were prepared. Columnar soil samples consist of seven A-samples mixed with sand and silt by ratio of 7:3 and three B-samples by ratio of 9:1. When fluid was injected into A-sample by pressure without plasma blasting, fluid penetrated into soil only near around the borehole, and penetration area ratio was less than 5%. Fluid was injected by plasma blasting with three different discharge energies of 1 kJ, 4 kJ and 9 kJ. When plasma blasting was performed once in the A-samples, penetration area ratios of the fluid were 16-25%. Penetration area ratios were 30-48% when blastings were executed five times consecutively. The largest penetration area by plasma blasting was 9.6 times larger than that by fluid injection by pressure. This indicates that the higher discharge energy of plasma blasting and the more numbers of blasting are, the larger are fluid penetration areas. When five consecutive plasma blasting were carried out in B-sample, fluid penetration area ratios were 33-59%. Penetration areas into B-samples were 1.1-1.4 times larger than those in A-samples when test conditions were the same, indicating that the higher permeability of soil is, the larger is fluid penetration area. The fluid penetration radius was calculated to figure out fluid penetration volume. When the fluid was injected by pressure, the penetration radius was 9 cm. Whereas, the penetration radius was 27-30 cm when blasting were performed 5 times with energy of 9 kJ. The radius increased up to 333% by plasma blasting. All these results indicate that cleaning agent penetrates further and remediation efficiency of contaminated soil will be improved if plasma blasting technology is applied to in situ cleaning of contaminated soil with low permeability.

• Asian-Australasian Journal of Animal Sciences
• /
• v.27 no.7
• /
• pp.1003-1012
• /
• 2014

The use of a suitable methodology to quantify the phytate phosphorus ($P_{phy}$) content in both the feed and the excreta from broilers is required to enable accurate calculation of the catalytic efficiency of the phytase supplemented in the feed. This study was conducted to compare 2 analytical methodologies (colorimetry and also high-performance liquid chromatography with a refractive index detector) in order to calculate the phytase efficiency by utilizing the results from the methodology that was shown to be the most appropriate. One hundred and twenty broilers were distributed in a $(4+1){\times}2$ factorial arrangement, corresponding to 4 diets that were equally deficient in P supplemented with increasing levels of phytase (0, 750, 1,500, and 2,250 units of phytase activity - FTU - per kg of feed) plus 1 positive control diet without phytase, supplied to male and female birds. The result indicated that the colorimetric methodology with an extraction ratio of 1:20 (mass of sample in g:volume of the solvent extractor in mL) was shown to be the most adequate. There was no interaction between the phytase level and the sex of the broilers (p>0.05). Males consumed 12% more $P_{phy}$ than did females (p<0.01), but the sex of the broilers did not affect (p>0.05) the excretion and retention coefficient of $P_{phy}$. The increase in the phytase level of the diet reduced (linear, p<0.01) the $P_{phy}$ excretion. The greatest $P_{phy}$ retention was estimated at 87.85% when the diet contained 1,950 FTU/kg (p<0.01), indicating that it is possible to reduce the inorganic P in the formulation at an amount equivalent to 87.85% of the $P_{phy}$ content present in the feed, which, in this research, corresponds to a decrease in 2.86 g of P/kg of the feed.