• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 Proceedings ICPE 01 2001 International Conference on Power Electronics
• /
• pp.508-511
• /
• 2001

This paper deals with the control algorithm of series voltage compensator that is used to maintain the load voltage when the supply voltage deviates from its nominal voltage. The two reference frame-based controllers using the state feedback algorithm are proposed and verified in the simulation and the experiment The simulation and the experiment show the effectiveness of the proposed control algorithm.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.183-185
• /
• 2006

This paper presents a SISO nonlinear controller for the power system consisting of a synchronous generator connected to an infinite bus. The proposed controller is based on input-output feedback linearization, with a modified version of the terminal voltage equation used as the output. The resulting closed-loop has no internal dynamics, and thus stability is guaranteed. The controller performance is seen to be effective through simulations.

• 센서학회지
• /
• 제18권4호
• /
• pp.274-279
• /
• 2009

In this paper, a wide dynamic range active pixel sensor(APS) with output voltage feedback structure has been designed by a 2-poly 4-metal 0.35 $\mu$m standard CMOS technology. We presented a novel APS with output voltage feedback, which exhibits a wide dynamic range. The dynamic range increases at the cost of an additional diode and an additional MOSFET. The output voltage feedback structure enables the control of the output voltage level by itself, as incident light power varies. It is confirmed that the light level which the output voltage level of proposed APS is saturated is about 120,000 lux, which is higher than that of a conventional 3-transistor APS.

• 전기전자학회논문지
• /
• 제26권3호
• /
• pp.462-467
• /
• 2022

피드백 버퍼 구조는 오버슈트 및 언더슈트 현상 및 출력전압의 레귤레이션을 완화하기 위해 제안된다. 기존의 LDO 레귤레이터는 일정한 부하전류의 변화로 인해 발생하는 레귤레이션 전압 변화를 겪는다. 따라서 패스 트랜지스터의 게이트 단자의 전류를 충방전함으로써 패스 트랜지스터의 동작 속도가 향상된다. 피드백 버퍼 구조를 갖는 LDO 레귤레이터는 3.3~4.5V에서 동작하며 출력 전압은 3V이며, 최대 150mA의 부하 전류를 가집니다. 시뮬레이션 결과에 따라 부하전류가 150mA까지 일정하게 변화하였을 때 6.2mV의 레귤레이션 값을 확보하였다.

• Journal of Power Electronics
• /
• 제16권1호
• /
• pp.351-361
• /
• 2016

Power quality is a critical issue in distribution systems, where a dynamic voltage restorer (DVR) is commonly used to mitigate the voltage disturbances for loads. This paper deals with a nonlinear control for the three-phase four-wire (3P-4W) DVR under a grid voltage unbalance and nonlinear loads in the distribution system, where a novel control scheme based on the feedback linearization technique is proposed. Through feedback linearization, a nonlinear model of a DVR with a PWM voltage-source inverter (VSI) and LC filters is linearized. Then, the controller design of the linearized model is performed by applying the linear control theory, where the load voltages are kept constant by controlling the d-q-0 axis components of the DVR output voltages. To keep the load voltage unchanged, an in-phase compensation strategy is employed, where the load voltages are recovered to be the same as the previous voltage without a change in the magnitude. With this strategy, the performance of the DVR becomes faster and more stable even under unbalanced source voltages and nonlinear loads. The validity of the proposed control strategy has been verified by simulation and experimental results.

• 전력전자학회논문지
• /
• 제23권4호
• /
• pp.281-285
• /
• 2018

An isolated feedback method for measuring the inverter DC-link voltage is proposed. This method provides a simple and economical solution to inverter control systems that use a flyback converter as a controller power supply. In the proposed method, data on the DC-link voltage are acquired when the primary side voltage appears on the secondary side of the flyback transformer, thereby eliminating the need to adopt an extra signal isolation method. To solve the non-synchronization problem between the flyback converter switching and main controller sampling, the external interrupt function of the micro-controller is used as a trigger signal for the A/D conversion.

• 전력전자학회논문지
• /
• 제19권6호
• /
• pp.522-529
• /
• 2014

This study proposes an isolation amplifier circuit for the sensing and feedback of inverter DC-link voltage, which is inevitable for the precise control of inverter output voltage. The isolation amplifier consists of a pulse-width modulator and a pulse transformer with dual secondary windings. The accuracy of the proposed circuit depends on the precise matching of filter parameters in dual secondary circuits. The influences of parameter inaccuracy on the amplifier performances are analyzed. A modified circuit is proposed to reduce the dependency on filter parameters. The validity of the proposed method is verified through simulation and experiment.

• 전기학회논문지P
• /
• 제64권2호
• /
• pp.79-84
• /
• 2015

Voltage sags are considered the dominant disturbances affecting power quality. Dynamic voltage restorers(DVRs) are mainly used to protect sensitive loads from the electrical network voltage disturbances such as sags or swells and could be used to reduce harmonic distortion of ac voltages. The typical DVR topology essentially contains a PWM inverter with LC Filter, an injection transformer connected between the ac voltage line and the sensitive load, and a DC energy storage device. For injecting series voltage, the PWM inverter is used and the passive filter consist of inductor(L) and capacitor(C) for harmonics elimination of the inverter. However there are voltage pulsation responses by the characteristic of the LC passive filter that eliminate the harmonics of the PWM output waveform of the inverter. Therefore, this paper presented design and feedback performance of LC filter used in the DVRs. The voltage control by LC filter should be connected in the line side since this feedback method allows a relatively faster dynamic response, enabling the elimination of voltage notches or spikes in the beginning and in the end of sags and strong load voltage THD reduction. Illustrative examples are also included.

• 전기의세계
• /
• 제26권3호
• /
• pp.63-68
• /
• 1977

In this paper, the theory of pulse frequency modulated DC/DC power converter to obtain constant output voltage for all input voltage changes is discussed. The switch controller consisting of integrator and comparator determines the ON time of power switch-Thyristor-by the error between the load voltage and a load reference voltage. Resulting voltage and current waveforms have been studied theoretically in detail and verified experimentally for a resistive and inductive load condition. State equations for voltages and currents using binary logic variables are computed by digital computer. Comparison of these withe oscillograms obtained from an experimental model shows very close agreement.

• 한국정밀공학회지
• /
• 제23권6호
• /
• pp.104-110
• /
• 2006

A design and control of electrostatic suspension system for flexible objects is presented. A number of electrode pairs of which the number depends on the object flexibility are positioned above the object and the voltages applied to each electrode pair are controlled, independently on the others, on the basis of the gap length. To implement the system with low cost and compactness, switched-voltage control scheme that is based on the relay feedback control is utilized. Relay feedback control method deploys only a single high-voltage power supply that can deliver a DC voltage of positive and/or negative polarity and thus high voltage amplifiers that are costly and bulky are not needed any more. It is shown that despite the inherent limit cycle property of the relay feedback based control, an excellent performance in vibration suppression is attained due to the presence of a relatively large squeeze film damping originating from the electrodes and levitated object. Employing fourteen electrode pairs, a thin aluminum plate with a thickness of 0.1 mm has been suspended at a gap length of 0.75mm.