• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.506-508
• /
• 2007

In this paper, the induction motor bearing fault diagnosis system using current signals which are measured by over-sampling method is presented. In the case of inverter fed motor drive unlike line-driven motor drive, that make a lot of noise which can cause a wrong fault signals because of PWM(pulse width modulation) voltage. So, the current signals for fault diagnosis need very precise and high resolution information, which means this system demand additional hardware such as low pass filter, high resolution ADC system and so on to use fault diagnosis system. Therefore, the proposed over-sampling method is expected to contribute to low cost fault diagnosis system even though previous inverter fed motor drive without any additional hardware. In order to confirm the presented algorithms, various experiments for bearing faults are tested and the line current spectrum of each faulty situation using park transformation is compared with a FFT results.

• The Korean Journal of Pain
• /
• v.27 no.2
• /
• pp.103-111
• /
• 2014

Nefopam (NFP) is a non-opioid, non-steroidal, centrally acting analgesic drug that is derivative of the nonsedative benzoxazocine, developed and known in 1960s as fenazocine. Although the mechanisms of analgesic action of NFP are not well understood, they are similar to those of triple neurotransmitter (serotonin, norepinephrine, and dopamine) reuptake inhibitors and anticonvulsants. It has been used mainly as an analgesic drug for nociceptive pain, as well as a treatment for the prevention of postoperative shivering and hiccups. Based on NFP's mechanisms of analgesic action, it is more suitable for the treatment of neuropathic pain. Intravenous administration of NFP should be given in single doses of 20 mg slowly over 15-20 min or with continuous infusion of 60-120 mg/d to minimize adverse effects, such as nausea, cold sweating, dizziness, tachycardia, or drowsiness. The usual dose of oral administration is three to six times per day totaling 90-180 mg. The ceiling effect of its analgesia is uncertain depending on the mechanism of pain relief. In conclusion, the recently discovered dual analgesic mechanisms of action, namely, a) descending pain modulation by triple neurotransmitter reuptake inhibition similar to antidepressants, and b) inhibition of long-term potentiation mediated by NMDA from the inhibition of calcium influx like gabapentinoid anticonvulsants or blockade of voltage-sensitive sodium channels like carbamazepine, enable NFP to be used as a therapeutic agent to treat neuropathic pain.

• The Korean Journal of Physiology and Pharmacology
• /
• v.10 no.2
• /
• pp.59-64
• /
• 2006

The effects of $Zn^{2+}$ on spontaneous glutamate and GABA release were tested in mechanically dissociated rat CA3 pyramidal neurons which retained functional presynaptic nerve terminals. The spontaneous miniature excitatory and inhibitory postsynaptic currents (mEPSCs and mIPSCs, respectively) were pharmacologically isolated and recorded using whole-cell patch clamp technique under voltage-clamp conditions. $Zn^{2+}$ at a lower concentration $(30{\mu}M)$ increased GABAergic mIPSC frequency without affecting mIPSC amplitude, but it decreased both mIPSC frequency and amplitude at higher concentrations $({\ge}300{\mu}M)$. In contrast, $Zn^{2+}$ (3 to $100{\mu}M$) did not affect glutamatergic mEPSCs, although it slightly decreased both mIPSC frequency and amplitude at $300{\mu}M$ concentration. Facilitatory effect of $Zn^{2+}$ on GABAergic mIPSC frequency was occluded either in $Ca^{2+}$-free external solution or in the presence of $100{\mu}M$ 4-aminopyridine, a non-selective $K^{+}$ channel blocker. The results suggest that $Zn^{2+}$ at lower concentrations depolarizes GABAergic nerve terminals by blocking $K^{+}$ channels and increases the probability of spontaneous GABA release. This $Zn^{2+}$-mediated modulation of spontaneous GABAergic transmission is likely to play an important role in the regulation of neuronal excitability within the hippocampal CA3 area.

• The Korean Journal of Physiology and Pharmacology
• /
• v.10 no.6
• /
• pp.297-302
• /
• 2006

Melittin, a major component of bee venom, produces a sustained decrease in mechanical threshold, and an increase in spontaneous flinchings and paw thickness, which are characteristics similar to those induced by whole bee venom. Melittin-induced nociception has been known to be modulated by the changes in the activity of excitatory amino acid receptors, voltage-dependent calcium channels, cyclooxygenase and serotonin receptors. The present study was undertaken to investigate the role of calcium chelators (TMB-8 & Quin 2) in melittin-induced nociceptive responses. Changes of mechanical threshold and spontaneous flinching behaviors were measured at a given time point following intraplantar injection of melittin ($30{\mu}g/paw$). Intrathecal or intraplantar pre-administration and intrathecal posttreatment of TMB-8 and Quin 2 significantly prevented the melittin-induced reduction of mechanical threshold, and intraplantar or intrathecal pre-treatment of TMB-8 and Quin 2 suppressed melittininduced flinching behaviors. These results indicate that calcium ion in the spinal dorsal horn neurons and peripheral nerves plays an important role in the production and maintenance of mechanical allodynia and spontaneous pain by melittin.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.12
• /
• pp.136-145
• /
• 2009

This paper proposes control methods and simulation models of a driving system, which consists of converters and inverters, for high speed trains employing multi-level power converters. The control method of a single phase three-level converter for high-speed trains is designed to use DC values instead of instantaneous current values which are usually used in single-phase application, so that it results in a fast and robust voltage control response. In addition, simulation models of Space Vector Pulse Width Modulation (SVPWM) for single phase three-level converters as well as three level inverters are proposed. Experimental results demonstrate the validity of the simulation model for three-level inverters.

• Journal of Power Electronics
• /
• v.15 no.2
• /
• pp.399-410
• /
• 2015

A 6.5 V/50 kA high-frequency switching power supply (HSPS) system composed of 10 power modules is developed to meet the requirements of copper-foil electrolysis. The power module is composed of a two-leg pulse width modulation (PWM) rectifier and a DC/DC converter. The DC/DC converter adopts two full-wave rectifiers in parallel to enhance the output. For the two-leg PWM rectifier, the ripple of the DC-link voltage is derived. A composite control method with a ripple filter is then proposed to effectively improve the performance of the rectifier. To meet the process demand of copper-foil electrolysis, the virtual impedance-based current-sharing control method with load current full feedforward is proposed for n-parallel DC/DC converters. The roles of load current feedforward and virtual impedance are analyzed, and the current-sharing control model of the HSPS system is derived. Virtual impedance is used to adjust the current-sharing impedance without changing the equivalent output impedance, which can effectively reduce current-sharing errors. Finally, simulation and experimental results verify the structure and control method.

• Journal of Power Electronics
• /
• v.15 no.2
• /
• pp.309-318
• /
• 2015

This study proposes a dual-output single-stage bridgeless single-ended primary-inductor converter (DOSSBS) that can completely remove the front-end full-bridge alternating current-direct current rectifier to accomplish power factor correction for universal line input. Without the need for bridge diodes, the proposed converter has the advantages of low component count and simple structure, and can thus significantly reduce power loss. DOSSBS has two uncommon output ports to provide different voltage levels to loads, instead of using two separate power factor correctors or multi-stage configurations in a single stage. Therefore, this proposed converter is cost-effective and compact. A magnetically coupled inductor is introduced in DOSSBS to replace two separate inductors to decrease volume and cost. Energy stored in the leakage inductance of the coupled inductor can be completely recycled. In each line cycle, the two active switches in DOSSBS are operated in either high-frequency pulse-width modulation pattern or low-frequency rectifying mode for switching loss reduction. A prototype for dealing with an $85-265V_{rms}$ universal line is designed, analyzed, and built. Practical measurements demonstrate the feasibility and functionality of the proposed converter.

• Journal of Power Electronics
• /
• v.11 no.3
• /
• pp.271-278
• /
• 2011

This paper presents a LLC resonant controller IC for secondary side control without external active devices to achieve low profile and low cost LED back light units. A gate driving transformer is adopted to isolate the primary side and the secondary side instead of an opto-coupler. A new integrated dimming circuitry is proposed to improve the dynamic current control characteristic and the current density of a LED for the brightness modulation of a large screen LCD. A dual-slope clock generator is proposed to overcome the frequency error due to the under shoot in conventional approaches. This chip is fabricated using 0.35 ${\mu}m$ BCD technology and the die size is $2{\times}2\;mm^2$. The frequency range of the clock generator is from 50 kHz to 500 kHz and the range of the dead time is from 50 ns to 2.2 ${\mu}s$. The efficiency of the LED driving circuit is 97 % and the current consumption is 40 mA for a 100 kHz operation frequency from a 15 V supply voltage.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.4
• /
• pp.376-382
• /
• 2014

This paper proposes the pulse width modulation (PWM) control strategy for low-speed operation in the three-level neutral-point-clamped (NPC) inverters based on the bootstrap gate drive circuit. As a purpose of the cost reduction, several papers have paid attention to the bootstrap circuit applied to the three-level NPC inverter. However, the bootstrap gate driver IC cannot generate the gate signal to the IGBT for low-speed operation, because the bootstrap capacitor voltage decreases under the threshold level. For low-speed operation, the dipolar and partial-dipolar modulations can be the effective solution. However, these modulations have drawbacks in terms of the switching loss and THD. Therefore, this paper proposes the PWM control strategy to operate the inverter at low-speed and to minimize the switching loss and harmonics. The experimental results are presented to verify the validity on the proposed method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.22 no.2
• /
• pp.166-174
• /
• 2017

This study proposes a compensation method for the dead-time effects on a single-phase grid-connected inverter. Dead time should be considered in the pulse-width modulation gating signals to prevent the simultaneous conduction of switching devices, considering that a switching device has a finite switching time. Consequently, the output current of the grid-connected inverter contains odd-numbered harmonics because of the dead time and the nonlinear characteristics of the switching devices. The effects of dead time on output voltage and current are analyzed in this study. A new compensation algorithm based on second-order generalized integrator is also proposed to reduce the dead-time effect. Simulation and experimental results validate the effectiveness of the proposed compensation algorithm.