• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.356-356
• /
• 2010

Tribological behaviors of the hard film on soft substrate system were explored using the hard thin film of diamond-like carbon (DLC) coated the soft polymer of polydimethysiloxane (PDMS). A DLC film with the Young's modulus of 100 GPa was coated on PDMS substrate with Young's modulus of 10 MPa using plasma enhanced chemical vapor deposition (PECVD) technique. The deposition time was varied from 10 sec to 10 min, resulting in nanoscale roughness of wrinkle patterns with the thickness of 20 nm to 510 nm, respectively, at a bias voltage of $400\;V_b$, working pressure 10 mTorr. Nanoscale wrinkle patterns with 20-100 nm in width and 10-30 nm height were formed on DLC coating due to the residual stress in compression and difference in Young's modulus. Nanoscale roughness effect on tribological behaviors was observed by performing a tribo-experiment using the ball-on-disk type tribometer with a steel ball of 6 mm in diameter at the sliding speed of 220 rpm, normal load of 1N and 25% humidity at ambient temperature of $25^{\circ}C$. Friction force were measured with respect to thickness change of coated DLC thin film on PDMS. It was found that with increases the thickness of DLC coating on PDMS, the coefficient of friction decreased by comparison to that of the uncoated PDMS. The wear tracks before and after tribo-test were analyzed using SEM and AFM.

• 동의생리병리학회지
• /
• 제21권3호
• /
• pp.748-754
• /
• 2007

Electroacupuncture is the combined treatment of mechanical and electric stimuli on the needle head, on which electricity runs after acupuncturing at the acupuncture points. It is reported that its treatment effect depends on the parameter of stimulus, which is wave of stimulus, frequency, voltage, and duration of electric current. To get the effective treatment, stimulus intensity over threshold is needed. We planned to experiment whether acupuncture effect is affected by sex, age, and weight. After we conducted electric stimulus at Zusanli(ST 36) which is known to increase small intestinal motility in normal rats, we observed the effects and got the following results. Though the increased effects of small intestinal motility of electro-acupuncture at Zusanli(ST 36) did not show the difference of sex, this effect was observed to have a tendency to decrease according to weight increase without distinction of sex. But the effect of electro-acupuncture shown in 4, 5, 7 weeks old without distinction of sex was observed to have a tendency to decrease with the growing of weeks-old in the male rat group. And the significant change without specific tendency was observed in the 4, 5 weeks old female rat group. This result suggested that sex, weight, and age should be considered to get the efficient electro-acupuncture. The more experimental study should be advanced to investigate the correlation between the factors that can affect the acupuncture treatment, and, afterward, the interconnection into the clinical use.

• 한국산학기술학회논문지
• /
• 제10권9호
• /
• pp.2227-2235
• /
• 2009

본 논문에서는 마이크로파를 이용하는 무선 전력전송시스템의 간단한 구성과 측정한 동작 특성을 제시한다. 마이크로파 전력전송시스템은 건물 안, 회의실과 같은 좁은 공간내에서 저전력을 이동 단말 기기에 공급하는 것을 목표로 한다. 실험실 수준에서 프로토타입 시스템의 제작 및 측정이 용이하도록 각 구성 회로 소자들을 직접 설계 및 제작, 측정하였는데, 마이크로파 발진기, 고출력증폭기, 마이크로스트립 패치 안테나, 저역통과여파기, 검파 및 정류회로이다. 마이크로파 무선전력전송 시스템은 중심주파수 2.4GHz에서 고정 전력 29.3dBm을 생성하여 전송하고, 수신측 패치 안테나를 수신한 전력을 정류기를 통해서 DC 전력으로 변환한다. 두 안테나간 이격 거리에 따라 측정되는 DC 전압값의 차이를 제시하고, 각 거리별로 수신측에 전달되는 DC전력량이 서로 다름을 측정값으로 제시한다.

• Advances in nano research
• /
• 제8권1호
• /
• pp.83-94
• /
• 2020

An analytical formulation and solution process for the buckling analysis of porous magneto-electro-elastic functionally graded (MEE-FG) beam via different thermal loadings and various boundary conditions is suggested in this paper. Magneto electro mechanical coupling properties of FGM beam are taken to vary via the thickness direction of beam. The rule of power-law is changed to consider inclusion of porosity according to even and uneven distribution. Pores possibly occur inside FGMs due the result of technical problems that lead to creation of micro-voids in these materials. Change in pores along the thickness direction stimulates the mechanical and physical properties. Four-variable tangential-exponential refined theory is employed to derive the governing equations and boundary conditions of porous FGM beam under magneto-electrical field via Hamilton's principle. An analytical model procedure is adopted to achieve the non-dimensional buckling load of porous FG beam exposed to magneto-electrical field with various boundary conditions. In order to evaluate the influence of thermal loadings, material graduation exponent, coefficient of porosity, porosity distribution, magnetic potential, electric voltage and boundary conditions on the critical buckling temperature of the beam made of magneto electro elastic FG materials with porosities a parametric study is presented. It is concluded that these parameters play remarkable roles on the buckling behavior of porous MEE-FG beam. The results for simpler states are proved for exactness with known data in the literature. The proposed numerical results can serve as benchmarks for future analyses of MEE-FG beam with porosity phases.

• Journal of Industrial and Engineering Chemistry
• /
• 제68권
• /
• pp.117-123
• /
• 2018

Recently, aqueous method has attracted lots of attention because it enables the solution-processed metal oxide thin film with high electrical properties in low temperature fabrication condition to various flexible devices. Focusing the development of aqueous route, many researchers are only focused on metal oxide materials. However, for expansive application of the aqueous-based metal oxide films, the systematic study of performance change with process variables for the development of aqueous-based metal oxide insulator film is urgently required. Here, we propose importance of process variables to achieve high electrical-performance metal oxide insulator based on the aqueous method. We found that the significant process variables including precursor solution temperature and humidity during the spincoating process strongly affect chemical, physical, and electrical properties of $AlO_x$ insulators. Through the optimization of significant variables in process, an $AlO_x$ insulator with a leakage current value approximately $10^5$ times smaller and a breakdown voltage value approximately 2-3 times greater than un-optimized $AlO_x$ was realized. Finally, by introducing the optimized $AlO_x$ insulators to solutionprocessed $InO_x$ TFTs, we successfully achieved $InO_x/AlO_x$ TFTs with remarkably high average field-effect mobility of ${\sim}52cm^2V^{-1}\;s^{-1}$ and on/off current ratio of 106 at fabrication temperature of $250^{\circ}C$.

• Journal of Magnetics
• /
• 제10권3호
• /
• pp.122-127
• /
• 2005

New classes of LC resonators for micro magnetic sensor device were proposed and fabricated. The first type LC resonator (Type I) consists of a small piece of microwire and two cylindrical electrodes at the end of the microwire without direct contact to its ferromagnetic core. In type I resonator the ferromagnetic core of the microwire and cylindrical electrodes act as an inductor and two capacitors respectively to form a LC circuit. The second type LC resonator (Type II) consists of a solenoidal micro-inductor with a bundle of soft magnetic microwires as a core. The solenoidal micro-inductors fabricated by MEMS technique were $500\sim1,000\;\mu{m}$ in length with $10\sim20$ turns. A capacitor is connected in parallel to the micro-inductor to form a LC circuit. A tiny glass coated $CO_{83.2}B_{3.3}Si_{5.9}Mn_{7.6}$ microwire was fabricated by a glass-coated melt spinning technique. A supergiant magneto-impedance effect was found in a type I resonator as much as 400,000% by precise tuning frequency at around 518.51 MHz. In type II resonator the changes of inductance as a function of external magnetic field in micro-inductors with properly annealed microwire cores were varied as much as 370%. The phase angle between current and voltage was also strongly dependent on the magnetic field. The drastic increments of magnetoimpedance at near the resonance frequency were observed in both types of LC resonators. Accordingly, the sudden change of the phase angle, as large as $180^{\circ}C$, evidenced the occurrence of the resonance at a given external magnetic field.

• Archives of Pharmacal Research
• /
• 제29권4호
• /
• pp.310-317
• /
• 2006

We investigated the effects of trinitrobenzene sulfonic acid (TNBS), an amino-group reagent, on the human ether-a-go-go-related gene (HERG) $K^+$ channels expressed in Xenopus oocytes. TNBS neutralizes the positively charged amino-groups of peptide N-terminal and lysine residues. External application of TNBS at 10 mM for 5 min irreversibly shifted the curves for currents at the end of the pulse and tail currents of HERG to a more negative potential and decreased the maximal amplitude of the $I_{tail}$ curve $(I_{tail,max})$. TNBS had little effect on either the activated current-voltage relationship or the reversal potential of HERG current, indicating that TNBS did not change ion selectivity properties. TNBS shifted the time constant curves of both activation and deactivation of the HERG current to a more hyperpolarized potential; TNBS's effect was greater on channel opening than channel closing. External $H^+$ is known to inhibit HERG current by shifting $V_{1/2}$ to the right and decreasing $I_{tail,max}$. TNBS enhanced the blockade of external $H^+$ by exaggerating the effect of $H^+$ on $I_{tail,max}$, not on $V_{1/2}$. Our data provide evidence for the presence of essential amino-groups that are associated with the normal functioning of the HERG channel and evidence that these groups modify the blocking effect of external $H^+$ on the current.

• Journal of Power Electronics
• /
• 제19권5호
• /
• pp.1303-1314
• /
• 2019

This paper studies the harmonic characteristics of ship electric propulsion systems and their treatment methods. It also adopts effective measures to suppress and prevent ship power systems from affecting ship operation due to the serious damage caused by harmonics. Firstly, the harmonic characteristics of a ship electric propulsion system are reviewed and discussed. Secondly, aiming at problems such as resonant frequency and filter characteristics variations, resonance point migration, and unstable filtering performances in conventional passive filters, a method for fully tuning of a passive dynamic tunable filter (PDTF) is proposed to realize harmonic suppression. Thirdly, to address the problems of the uncontrollable inductance L of traditional air gap iron core reactors and the harmonics of power electronic impedance converters (PEICs), this paper proposes an electromagnetic coupling reactor with impedance transformation and harmonic suppression characteristics (ECRITHS), with the internal filter (IF) designed to suppress the harmonics generated by PEICs. The ECRITHS is characterized by both harmonic suppression and impedance change. Fourthly, the ECRITHS is investigated. This investigation includes the harmonic suppression characteristics and impedance transformation characteristics of the ECRITHS at the fundamental frequency, which shows the good performance of the ECRITHS. Simulation and experimental evaluations of the PDTF are carried out. Multiple PDTFs can be configured to realize multi-order simultaneous dynamic filtering, and can effectively eliminate the current harmonics of ship electric propulsion systems. This is done to reduce the total harmonic distortion (THD) of the supply currents to well below the 5% limit imposed by the IEEE-519 standard. The PDTF also can eliminate harmonic currents in different geographic places by using a low voltage distribution system. Finally, a detailed discussion is presented, with challenges and future implications discussed. The research results are intended to effectively eliminate the harmonics of ship electric power propulsion systems and to improve the power quality of ship power systems. This is of theoretical and practical significance for improving the power quality and power savings of ship power systems.

• 전기전자학회논문지
• /
• 제23권2호
• /
• pp.586-593
• /
• 2019

본 논문은 초미세먼지 증가를 억제하고자 1972년 건설된 국내무연탄과 유류를 혼소하는 발전설비를 2017년 국내최초, 최대 용량의 신재생 발전 연료 중 하나인 순수 목재를 가공한 친환경 고형연료인 바이오매스[우드팰릿] 발전방식으로 변경하였다. 발전기 제어계 중요 설비 교체에 따른 산업부 고시 "전력계통 신뢰도 및 전기품질 유지기준" 제 32조 발전설비 신/증설 시 발전설비 특성자료를 제출에 의거 발전기 기술특성시험을 실시하였으며, 시험을 통하여 발전기/제어계 모델정수 도출 및 검증을 수행하였다. 발전기 연료변경에도 해당 발전기 설비의 성능 및 여자시스템의 전압제어특성이 양호함을 재확인하였다. 차후 화석연료를 신재생 연료로 교체하고자 하는 발전소에서 참고하는데 기여할 수 있다.

• 한국인터넷방송통신학회논문지
• /
• 제18권6호
• /
• pp.207-212
• /
• 2018

태양광발전시스템에 대한 시험인증 기술력 향상을 위한 표준화를 위하여 기 구축된 분야에 대한 국가표준(안)을 제안 및 개정하고, 기업이 수출시 상대국이 인정하는 적합성평가(CB인증)가 국내에서 지원하는 것이 필수적이다. 이를 위하여 국제공인 적합성평가 기관으로서의 능력을 향상시켜 IECEE-CB 제도에 의한 인증기관(NCB-NREC) 및 시험기관으로의 위상 강화를 추진하여 국내기업이 수출장벽을 타개하고 외국에서 시험인증 받기 위한 기간을 단축하고 경비를 대폭 절감하여 수출의 증대 및 대외 경쟁력 확보가 필요하다. 또한 정부가 추진 중인 FTA에 교역시 기술장벽(TBT) 해소를 위한 상호인정 협정에 대비하기 위하여도 국내 시험인증기관의 능력향상이 필수적이다. 현재 태양광모듈 및 인버터의 안전성 평가는 유럽 및 일본에서 강제로 채택하여 국내업체 수출시 외국인증기관을 이용하고 있는 실정으로서 태양광모듈의 안전성 평가에 대한 CBTL를 취득함으로서 국내외 경쟁력 강화 및 태양광 발전 사업을 수출산업으로 육성지원 하는데 기여할 수 있다.