• 한국도로학회논문집
• /
• 제19권4호
• /
• pp.37-44
• /
• 2017

PURPOSES : Conductive and convective heat transfer simulations for an asphalt mixture were made by using discrete element method (DEM) and similarity principle. METHODS : In this research, virtual specimens composed of discrete element method particles were generated according to four different predetermined particle size distribution curves. Temperature variations of the four different particles for a given condition were estimated and were compared with measurements and analytical solutions. RESULTS : The virtual specimen with mixed particles and with the smallest particle show very good agreement with laboratory test results and analytical solutions. As particle size decreases, better heat transfer simulation can be performed due to smaller void ratio and more contact points and areas. In addition, by utilizing the similarity principle of thermal properties and corresponding time unit, analytical time can be drastically reduced. CONCLUSIONS : It is concluded that the DEM asphalt mixture specimens with similarity principle could be used to predict the temperature variation for a given condition. It is observed that the void ratio has critical effect on prediction of temperature variation. Comparing the prediction for a 4 mm particle specimen with a mixed particle specimen, it is also concluded that predicting the mixed particle specimen temperature is much more efficient considering the number of particles that are directly associated with computational time in DEM analysis.

• 한국농공학회지
• /
• 제31권1호
• /
• pp.106-116
• /
• 1989

This study aims at scrutinizing the long4errn consolidation characteristics of peats sampled at three different regions of Chonbuk province. The standard consolidation test and the single load consolidation test were performed about these samples and especially in case of the latter the loading period was 350 days. The main condusions analyzed are as follows. 1. Void ratio showed much greater values than that of the general clay and was decresed greatly according to the increase of the load. 2. In case of the relationship between the sefflement and the long-term settlement time the rate of settlement increment became great according to the increase of the load step and the long4erm settlement became linely proportional to the logarithm of time alter 10 minutes. 3. The linear correlation was showed between the long4erm settlement time and the void ratio and therefore equations by regression analysis were derived in order to estimate the long-term settlement The slope of straight lines increased according th the increase of the load step and secondary consolidation coefficients ranged from 0.04-0.27. 4. The secondary consolidation coeffcient became linealy proportional to the compression index and the ratio of Ca to CC was 0.072. 5. The period required in ending the primary consolidation was about 10 minutes and alter that the secondary consolidation coefficient appeared to have constant value. Therefore the secondary consolidation coefficient was judged to be used as a significant factor in estimating the long4erm settlement. 6. In case of the single load consolidation test the secondary consolidation coefficient showed the tendancy increasing according to the increase of the consolidation pressure.

• 한국연초학회지
• /
• 제29권1호
• /
• pp.23-29
• /
• 2007

The measurement of physical properties such as apparent density and void fraction of tobacco materials, which is so bulky, is a main theme with regard to tobacco process, quality control, cigarette combustion and smoke generation. Except Solution Impregnation Method, there was no alternative method for measuring those properties in the porous material so far. However, experimental processes of that method are so complicated as to cost much time and labor, the main solution such as mercury to apply to the method is usually very hazard. Therefore, we had developed a new method to determine them easily in our other paper by the mathematical equations derived from the Ergun equation for the purpose of it, and then already evaluated our method through applying some basic data from Muramatsu et at. (1979) with regard to our developed equations. Then, we found our method best fit to experimental one (Oh et al., 2001). In this study we tried to establish our method to conveniently determine those physical properties. Especially, we have focused on the development the easy way to measure surface area and the volume of single shred in a tobacco column. As a result of that, we found that the computer image analyzer was best fit for it. Then, we have finally determined apparent density and void fraction for our domestic tobacco shred.

• 대한토목학회논문집
• /
• 제28권1C호
• /
• pp.9-17
• /
• 2008

본 연구에서는 압밀 중에 위치별 간극수압의 측정을 통하여 시료 내 여러 위치에서 투수계수를 산정할 수 있는 이론해를 제시하였으며, 이를 바탕으로 간극비 및 체적압축계수를 산정할 수 있는 방법을 제안하였다. 또한 여러 위치에서 간극수압을 측정할 수 있는 방사내측배수가 가능한 대형압밀시험기를 제작하고 카올리나이트를 이용하여 압밀시험을 실시하였다. 시험결과로부터 압밀 중 투수계수, 간극비, 체적압축계수의 변화 및 시료 내 위치별 분포를 평가하였으며, 압밀완료 후 시료의 함수비 측정으로 평가된 값들과의 비교를 통하여 실험결과의 신뢰성을 검증하였다. 실험결과 투수계수, 체적압축계수, 간극비는 압밀 중 감소하며, 재하단계에 따라서도 감소함을 확인하였다. 또한 그 분포형태는 배수면 근처에서 가장 작고 배수거리에 따라 증가하며 비배수 경계면 근처에서는 오히려 약간 작은 것으로 나타났다.

• 마이크로전자및패키징학회지
• /
• 제31권1호
• /
• pp.35-42
• /
• 2024

최근 반도체 칩의 소형화 및 고집적화에 따라 미세 피치에 의한 범프 브리지 (bump bridge) 현상이 문제점으로 주목받고 있다. 이에 따라 범프 브리지 현상을 최소화할 수 있는 Cu pillar bump가 미세 피치에 대응하기 위해 반도체 패키지 산업에서 널리 적용되고 있다. 고온의 환경에 노출될 경우, 접합부 계면에 형성되는 금속간화합물(Intermetallic compound, IMC)의 두께가 증가함과 동시에 일부 IMC/Cu 및 IMC 계면 내부에 Kirkendall void가 형성되어 성장하게 된다. IMC의 과도한 성장과 Kirkendall void의 형성 및 성장은 접합부에 대한 기계적 신뢰성을 약화시키기 때문에 이를 제어하는 것이 중요하다. 따라서, 본 연구에서는 CS(Cu+ Sn-1.8Ag Solder) 구조 Cu pillar bump의 등온 시효 처리에 따른 접합부 특성 평가가 수행되었으며 그 결과가 보고되었다.

• 한국지반공학회논문집
• /
• 제27권9호
• /
• pp.13-24
• /
• 2011

Terzaghi의 1차원 압밀이론은 준설 매립지반과 같이 고함수비, 고압축성을 갖는 점토지반의 압밀해석에는 적합하지 않다. 준설 매립지반의 자중압밀과 재하하중에 의한 추가압밀을 적절히 고려하기 위해서는 비선형, 유한변형 압밀이론을 도입해야 한다. 준설 매립지반의 비선형 유한변형 압밀해석을 수행하기 위해서는 침강과정이 종료되고 자중압밀이 시작되는 시점의 간극비인 초기간극비($e_{00}$)와 비선형성을 갖는 준설토의 간극비-유효응력 관계와 간극비-투수계수의 관계 규명이 매우 중요하다. 본 연구에서는 실내시험을 통해 비선형 유한변형 압밀해석에 필요한 인자를 산정하는 방법을 제안하였다. 또한, 본 연구에서 제안한 방법을 적용하여 인천지역 준설토와 카올리나이트의 압밀 물성치를 평가하였고, 이를 동반논문에서 다룰 비선형 유한변형 압밀해석에 적용하였다.

• 한국정밀공학회지
• /
• 제3권1호
• /
• pp.40-49
• /
• 1986

Crack, craze and void are common defects which may be found in the bulk of polymeric materials such as either themoplastics or thermosets. The healing phenomena, autohesion, of these defects are known to be a intrinsic material property of various polymeric materials. However, only a few experimental and theoretical investigations on crack, void and craze healing phenomena for various polymeric materials have been reported up to date [1, 2, 3]. This may be partly due to the complications of healing processes and lacking of appropriate theoretical developments. Recently, some investigators have been urged to study the healing phenomena of various polymenic materials since the significance of the use of polymer based alloys or composites has been raised in terms of specific strength and energy saving. In the earlier published reports [1, 2, 3, 4], the crack and void healing velocity, healing toughness and some other healing mechanical and physical properties were measured experimentally and compared with predicted values by utilizing a simple model such as the reptation model under some resonable assumptions. It seems, however, that the general acceptance of the proposed modeling analyses is yet open question. The crack healing processes seem to be complicate and highly dependent on the state of virgin material in terms of mechanical and physical properties. Furthermore, it is also strongly dependent on the histories of crack, craze and void development including fracture suface morphology, the shape of void and the degree of disentanglement of fibril in the craze. The rate of crack healing may be a function of environmental factors such as healing temperature, time and pressure which gives different contact configurations between two separated surfaces. It seems to be reasonable to assume that the crack healing processes may be divided in several distinguished steps like stress relaxation with molecular chain arrangement, surface contact (wetting), inter- diffusion process and com;oete healing (to obtain the original strength). In this context, it is likely that we no longer have to accept the limitation of cumulative damage theories and fatigue life if it is probable to remove the defects such as crack, craze and void and to restore the original strength of polymers or polymer based compowites by suitable choice of healing histories and methods. In this paper, we wish to present a very simple and intuitive theoretical model for the prediction of healed fracture toughness of cracked or defective polymeric components. The central idea of this investigation, thus, may be the modeling of behavior of chain molecules under healing conditions including the effects of chain scission on the healing processes. The validity of this proposed model will be studied by making comparisons between theoretically predicted values and experimentally determined results in near future and will be reported elsewhere.

• 조명전기설비학회논문지
• /
• 제20권2호
• /
• pp.75-80
• /
• 2006

본 논문은 전력 케이블의 절연체인 XLPE 시료에 상용주파수 교류전압을 인가하였을 때, 절연열화에 의한 보이드방전 펄스신호와 AE신호 및 트리진전 특성을 검출하고 관찰하였다. 또한 XLPE 절연체의 트리 채널내 인가전압에 따라 보이드방전 펄스신호와 AE신호를 각각 관측하였다. 실험 결과 전력 케이블의 절연체인 XLPE 시료의 보이드 존재 유 무에 따른 트리진전 형상은 보이드 존재시에는 수지형으로 성장하였으나, 무보이드시에는 수초형으로 성장하였다. XLPE 절연체내의 트리진전 특성은 보이드 존재시에는 열화시간이 경과함에 따라 급격히 증가하였으나, 무보이드시에는 열화 시간이 경과함에 따라 트리의 성장 형상은 감소되는 것으로 나타났다. 전력 케이블 절연체인 XLPE의 트리 채널내 보이드방전에 의한 AE신호의 주파수 스펙트럼으로 분석한 결과, AE신호의 크기에 따라 변화되었으며 그 주파수 영역은 대략 1.0[MHz] 이하의 분포인 것으로 관측되었다.

• 마이크로전자및패키징학회지
• /
• 제11권2호
• /
• pp.53-58
• /
• 2004

63Sn-37Pb 공정솔더의 electromigration 현상을 용이하게 관찰하기 위해 63Sn-37Pb 공정솔 더를 증착하여 스트립 형태의 시편을 제작 후 electromigration 테스트를 실시하였다. $80{\sim}150^{\circ}C$의 온도 및 $1{\times}10^4{\sim}1{\times}10^5\;A/cm^2$의 전류밀도에서 electromigration 테스트시 스트립 형상의 63Sn-37Pb 솔더 합금에서 hillock과 void의 발생이 관찰되었으며, 온도와 전류밀도가 높아질수록 void의 형성이 빨라져서 평균파괴시간이 단축되었다. 평균파괴시간을 이용하여 Black의 식으로부터 구한 63Sn-37Pb 솔더 스트립의 electromigration에 대한 활성화 에너지는 $0.16{\sim}0.5\;eV$이었다.

• Archives of Plastic Surgery
• /
• 제48권5호
• /
• pp.528-533
• /
• 2021

Bladder acontractility affects several thousand patients in the United States, but the available therapies are limited. Latissimus dorsi detrusor myoplasty (LDDM) is a therapeutic option that allows patients with bladder acontractility to void voluntarily. Our goal was to conduct a systematic review of the literature to determine whether LDDM is a better option than clean intermittent catheterization (CIC) (standard treatment) in patients with bladder acontractility. On January 17, 2020, we conducted a systematic review of the PubMed/MEDLINE, Cochrane Clinical Answers, Cochrane Central Register of Controlled Trials, Embase, and ClinicalTrials.gov databases, without time frame limitations, to identify articles on the use of LDDM for bladder acontractility. Of 75 potential articles, 4 fulfilled the eligibility criteria. The use of LDDM to treat patients with bladder acontractility was reported in four case series by the same group in Europe. Fifty-eight patients were included, and no comparison groups were included. The most common cause of bladder acontractility was spinal cord injury (n=36). The mean (±standard deviation) operative time was 536 (±22) minutes, postoperative length of hospital stay ranged from 10 to 13 days, and follow-up ranged from 9 to 68 months. Most patients had complete response, were able to void voluntarily, and had post-void residual volume less than 100 mL. Although promising outcomes have been obtained, evidence is still weak regarding whether LDDM is better than CIC to avoid impairment of the urinary tract among patients with bladder acontractility. Further prospective studies with control groups are necessary.