• Journal of Korean Society of Water and Wastewater
• /
• v.7 no.1
• /
• pp.46-53
• /
• 1993

This study was carried out to examine substrate removal characteristics with the variation of the hydraulic retention time in an anaerobic filter. The feed concentration of synthetic wastewater used in the experiment was $10,000mg/l$ glucose. As media, the porosity of volcanic stones in Jeju island were 76%. The conditions of the experiment were as follows; HRT ranging from 1 day to 3 day, loading rates ranging from 3.33kg $COD_{er}/void\;m^3.day$ to 10kg $COD_{er}/void\;m^3.day$ and a temperature $35^{\circ}C$. Based on the results of the experiments, the COD removal efficiency was 98~99% in $COD_{er}$ method with loading rates ranging from 3.33kgCOD/void $m^3.day$ to 10kg COD/void $m^3.day$ and HRT ranging from 1day to 3 day. The produced quantity of gas equivalant to a porosity volume was $1.332~3.756Nm^3/void\;m^3.day$. The relationship between $COD_{er}$ loading rates and gas produced quantity equivalant to a porosity volume was well fitted with the equation of $Nm^3/void\;m^3.day{\cdot}=0.359L_0+0.179$($L_0=COD$ loading rate). Judging from the removal efficiency in this experiment, We concluded that anaerobic filter using Volcanic stones is one of improved and effective. As media, practical value of volcanic stones is sufficient.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.11a
• /
• pp.249-252
• /
• 2000

To overcome problems of excavation technology far repairing or replacing underground buried pipes which are worn out or damaged, various trenchless repair-reinforcement technologies have been invented. But these trenchless technologies also have many problems in the aspect of economy and convenience of operation. In this research, the repair-reinforcement process using RTM (Resin Transfer Molding) which can solve problems of present trenchless technologies was developed. The resin wetting and void removal during RTM process to form large composite structures inside of buried pipes were experimentally investigated. From the experiment, it was found that the new technology had advantage over conventional methods by employing appropriate process parameters and void removal vents.

• The Journal of the Korean dental association
• /
• v.55 no.8
• /
• pp.542-555
• /
• 2017

1. Diagnosis Diagnosis of Crack, Direct pulp capping 2. Access opening Find the calcified canal orifice Removal of dentin shelf Obtaining the MB2 canal (MB2, MB3, DB2) 3. Perforation repair during endodontic treatment 4. Removal of the separated files 5. Open apex treatment 6. Void removal on CWT procedure 7. Re-endodontic treatment Removal of restorative material filled in pulp chamber Post removal Identification and removal of residual gutta-perch 8. Surgical endodontic treatment In each case will overview how to use a dental microscope.

• The International Journal of Costume Culture
• /
• v.5 no.2
• /
• pp.53-65
• /
• 2002

Morphology of polyester fiber was physically modified by solvent treatment. PET fiber was treated with N,N-dimethylformamide (DMF) at 100, 120, $140^{circ}C$ for 10 minutes without tension. The structural changes in the morphology of DMF-induced modified PET fiber were FTIR and SEM analysis. Also dyeing behavior of DMF-treated polyester fibers with various disperse dyes was studied to detect changes of amorphous area in fine structure. DMF treatment resulted in increases in total void content, degree of crystallinity, trans isomer content, chain folding, segmental mobility and molecular packing, but it resulted in decreases in amorphous orientation, intermolecular forces and individual void size through longitudinal shrinkage, lateral welling and removal of oligomers. Void-size distribution could be estimated from the dye uptake with various sizes of disperse dyes. In contrast to the large increases in dye uptake with small dye molecules, there is no and little dye uptake with the bulkiest dye, which means that void size is bigger or smaller than the volume of each dye. Diffusion rates of dye molecules showed increases. This dyeing study revealed that the disperse dyeing is very effective method for characterizing the internal morphology of polyester fiber.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.310-313
• /
• 2002

Structures obtained with a direct boning of two FZ silicon wafers joined in such a way that a smooth surface of one wafer was attached to the grooved surface of the other were studied. A square net of grooves was made with a conventional photo lithography process. After high temperature annealing the appearance of voids and the rearrangement of structural defects were observed with X-ray diffraction topography techniques. It was shown that the formation of void free grooved boundaries was feasible. In the cases when particulate contamination was prevented, the voids appeared in the grooved structures could be eliminated with annealing. Since it was found that the flattening was accompanied with plastic deformation, this deformation was suggested to be intensively involved in the process of void removal. A model was proposed explaining the interaction between the structural defects resulted in "a dissolution" of cavities. The described processes may occur in grooved as well as in smooth structures, but there are the former that allow to manage air traps and undesirable excess of dislocation density. Grooves can be paths for air leave. According to the established mechanisms, if not outdone, the dislocations form local defect arrangements at the grooves permitting the substantial reduction in defect density over the remainder of the interfacial area.

• Journal of Environmental Science International
• /
• v.7 no.5
• /
• pp.679-685
• /
• 1998

The Soysauce wastewater removal characteristics of submerged biofilters filled with two filter media respectively were experimentally examined with constant temperature, pH value and variable BOD loading and recirculation ratio. The decreasing order of BOD removal is Netring(random plastic media), cubic wire meshes(plastic module). This is mainly due to the media characteristics such as void ratio, specific surface area and media shapes. The BOD removal ratio decreases with increasing $BOD_5$/ volumetric loading rate, and the loading rate for the BOD removal over 85% is lower than 1.5kg$BOD_5$ 5/$m^3$d for the plastic media of Netring and cubic wire meshes. The $BOD_5$ removal rate increases with the recirculation ratio, but the rate of increase become smaller as the recirculation ratio increases over 20. When $BOD_5$ volumetric loading is 1.5kg$BOD_5$/$m^3$d, the required recirculation ratio to obtain 85% BOD$_{5}$ removal is about 20 for Netring and it was about 30 for cubic wire meshes.s.

• Environmental Engineering Research
• /
• v.13 no.1
• /
• pp.19-27
• /
• 2008

Simultaneous removal of ternary gases of $NH_3$, $H_2S$ and toluene in a contaminated air stream was investigated over 180 days in a biofilter. A commercially available inorganic/polymeric composite chip with a large void volume (bed porosity > 0.80) was used as a microbial support. Multiple microorganisms including Nitrosomonas and Nitrobactor for nitrogen removal, Thiobacillus thioparus (ATCC 23645) for $H_2S$ removal and Pseudomonas aeruginosa (ATCC 15692), Pseudomonas putida (ATCC 17484) and Pseudomonas putida (ATCC 23973) for toluene removal were used simultaneously. The empty bed residence time (EBRT) ranged from 60 - 120 seconds and the inlet feed concentration was $0.0325\;g/m^3-0.0651\;g/m^3$ for $NH_3$, $0.0636\;g/m^3-0.141\;g/m^3$ for $H_2S$, and $0.0918\;g/m^3-0.383\;g/m^3$ for toluene, respectively. The observed removal efficiency was 2% - 98% for $NH_3$, 2% - 100% for $H^2S$, and 2% - 80% for toluene, respectively. Maximum elimination capacity was about $2.7\;g/m^3$/hr for $NH_3$, > $6.4\;g/m^3$/hr for $H_2S$ and $4.0\;g/m^3$/hr for toluene, respectively. The inorganic/polymeric composite carrier required 40 - 80 days of wetting time for biofilm formation due to the hydrophobic nature of the carrier. Once the surface of the carrier was completely wetted, the microbial activity became stable. During the long-term operation, pressure drop was negligible because the void volume of the carrier was two times higher than the conventional packing materials.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.2
• /
• pp.32-40
• /
• 2017

In this study, the procedures for quantitative measurement of void contents of carbon fiber/epoxy composites were suggested. Two types of the composites were considered: autoclave cured composite and filament wound composite. Void contents of the composites were evaluated by the density of the composites and their constituents, which was determined from weights in the air and water, and the weight fraction and volume fraction of the constituents obtained from the digestion method and combustion method. The surfaces of filtered carbon fibers were examined by FE-SEM in order to investigate the validity of resin removal from the composites. According to the results, the resin in the composites could be fully removed by the digestion method and combustion method. Therefore, the weight fraction and volume fraction of the constituents, and void content of the composites could be quantitatively obtained by the suggested procedures.

• Journal of Korean Society of Water and Wastewater
• /
• v.10 no.1
• /
• pp.112-120
• /
• 1996

In this study, the porous glass media was utilized as biomass carrier, and the optimum characteristics of this new media in fixed bed biofilm process were investigated. The characteristics of media considered here are a void volume fraction, a specific surface area, and surface characteristics of media. The effect of surface roughness and material could be clearly demonstrated by the fact that the porous glass media showed a good potential for biofilm development. This might results from the fact that biofilm is initially formed in the surface cavities of the media is protect from the shear effect. Therefore, the microcolonies are not readily detached by the fluid shear. In the steady state, biofilm formation along the packing bed depth was different from media to media. The specific area was also an important factor for the attachment of microorganism on the media surface. The specific area was also an important factor for the attachment of microorganism on the media surface. In the case of porous glass media, about $100m^2/m^3$ was enough to obtain a good organic removal efficiency The organic removal efficiency could be improved by increasing the void volume fraction in the reactor, at least 80% was required to obtain a high removal efficiency and prevent clogging. From the analysis of kinetics study, the yield coefficient, Y, was 0.42 mgMLSS/mgSBOD, endogenous respiration coefficient, ke, was $0.12day^{-1}$ and substrate removel coefficient of Mckinney. km, was $16.8hr^{-1}$ for the porous glass media G-2

• Journal of the Korean Ceramic Society
• /
• v.39 no.7
• /
• pp.693-698
• /
• 2002

Reaction-Bonded Silicon Carbide (RBSC) Ceramics were fabricated which satisfies the maximum packing density of silicon carbide skeleton in the green compacts. Such a high packing density induced incomplete infiltration during reaction-sintering; forms linear void around the interface of large alpha silicon carbide powders. During reaction-sintering, the limited extraction and entrapped gas induced by residue oxide was considered to be a reason of linear void formation. In order to improve infiltration behavior in the highly packed preform, the pre-treatment methods for residue oxide removal were proposed.