• 상하수도학회지
• /
• 제7권1호
• /
• pp.46-53
• /
• 1993

This study was carried out to examine substrate removal characteristics with the variation of the hydraulic retention time in an anaerobic filter. The feed concentration of synthetic wastewater used in the experiment was $10,000mg/l$ glucose. As media, the porosity of volcanic stones in Jeju island were 76%. The conditions of the experiment were as follows; HRT ranging from 1 day to 3 day, loading rates ranging from 3.33kg $COD_{er}/void\;m^3.day$ to 10kg $COD_{er}/void\;m^3.day$ and a temperature $35^{\circ}C$. Based on the results of the experiments, the COD removal efficiency was 98~99% in $COD_{er}$ method with loading rates ranging from 3.33kgCOD/void $m^3.day$ to 10kg COD/void $m^3.day$ and HRT ranging from 1day to 3 day. The produced quantity of gas equivalant to a porosity volume was $1.332~3.756Nm^3/void\;m^3.day$. The relationship between $COD_{er}$ loading rates and gas produced quantity equivalant to a porosity volume was well fitted with the equation of $Nm^3/void\;m^3.day{\cdot}=0.359L_0+0.179$($L_0=COD$ loading rate). Judging from the removal efficiency in this experiment, We concluded that anaerobic filter using Volcanic stones is one of improved and effective. As media, practical value of volcanic stones is sufficient.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 추계학술발표대회 논문집
• /
• pp.249-252
• /
• 2000

To overcome problems of excavation technology far repairing or replacing underground buried pipes which are worn out or damaged, various trenchless repair-reinforcement technologies have been invented. But these trenchless technologies also have many problems in the aspect of economy and convenience of operation. In this research, the repair-reinforcement process using RTM (Resin Transfer Molding) which can solve problems of present trenchless technologies was developed. The resin wetting and void removal during RTM process to form large composite structures inside of buried pipes were experimentally investigated. From the experiment, it was found that the new technology had advantage over conventional methods by employing appropriate process parameters and void removal vents.

• 대한치과의사협회지
• /
• 제55권8호
• /
• pp.542-555
• /
• 2017

1. Diagnosis Diagnosis of Crack, Direct pulp capping 2. Access opening Find the calcified canal orifice Removal of dentin shelf Obtaining the MB2 canal (MB2, MB3, DB2) 3. Perforation repair during endodontic treatment 4. Removal of the separated files 5. Open apex treatment 6. Void removal on CWT procedure 7. Re-endodontic treatment Removal of restorative material filled in pulp chamber Post removal Identification and removal of residual gutta-perch 8. Surgical endodontic treatment In each case will overview how to use a dental microscope.

• The International Journal of Costume Culture
• /
• 제5권2호
• /
• pp.53-65
• /
• 2002

Morphology of polyester fiber was physically modified by solvent treatment. PET fiber was treated with N,N-dimethylformamide (DMF) at 100, 120, $140^{circ}C$ for 10 minutes without tension. The structural changes in the morphology of DMF-induced modified PET fiber were FTIR and SEM analysis. Also dyeing behavior of DMF-treated polyester fibers with various disperse dyes was studied to detect changes of amorphous area in fine structure. DMF treatment resulted in increases in total void content, degree of crystallinity, trans isomer content, chain folding, segmental mobility and molecular packing, but it resulted in decreases in amorphous orientation, intermolecular forces and individual void size through longitudinal shrinkage, lateral welling and removal of oligomers. Void-size distribution could be estimated from the dye uptake with various sizes of disperse dyes. In contrast to the large increases in dye uptake with small dye molecules, there is no and little dye uptake with the bulkiest dye, which means that void size is bigger or smaller than the volume of each dye. Diffusion rates of dye molecules showed increases. This dyeing study revealed that the disperse dyeing is very effective method for characterizing the internal morphology of polyester fiber.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.310-313
• /
• 2002

Structures obtained with a direct boning of two FZ silicon wafers joined in such a way that a smooth surface of one wafer was attached to the grooved surface of the other were studied. A square net of grooves was made with a conventional photo lithography process. After high temperature annealing the appearance of voids and the rearrangement of structural defects were observed with X-ray diffraction topography techniques. It was shown that the formation of void free grooved boundaries was feasible. In the cases when particulate contamination was prevented, the voids appeared in the grooved structures could be eliminated with annealing. Since it was found that the flattening was accompanied with plastic deformation, this deformation was suggested to be intensively involved in the process of void removal. A model was proposed explaining the interaction between the structural defects resulted in "a dissolution" of cavities. The described processes may occur in grooved as well as in smooth structures, but there are the former that allow to manage air traps and undesirable excess of dislocation density. Grooves can be paths for air leave. According to the established mechanisms, if not outdone, the dislocations form local defect arrangements at the grooves permitting the substantial reduction in defect density over the remainder of the interfacial area.

• 한국환경과학회지
• /
• 제7권5호
• /
• pp.679-685
• /
• 1998

The Soysauce wastewater removal characteristics of submerged biofilters filled with two filter media respectively were experimentally examined with constant temperature, pH value and variable BOD loading and recirculation ratio. The decreasing order of BOD removal is Netring(random plastic media), cubic wire meshes(plastic module). This is mainly due to the media characteristics such as void ratio, specific surface area and media shapes. The BOD removal ratio decreases with increasing $BOD_5$/ volumetric loading rate, and the loading rate for the BOD removal over 85% is lower than 1.5kg$BOD_5$ 5/$m^3$d for the plastic media of Netring and cubic wire meshes. The $BOD_5$ removal rate increases with the recirculation ratio, but the rate of increase become smaller as the recirculation ratio increases over 20. When $BOD_5$ volumetric loading is 1.5kg$BOD_5$/$m^3$d, the required recirculation ratio to obtain 85% BOD$_{5}$ removal is about 20 for Netring and it was about 30 for cubic wire meshes.s.

• Environmental Engineering Research
• /
• 제13권1호
• /
• pp.19-27
• /
• 2008

Simultaneous removal of ternary gases of $NH_3$, $H_2S$ and toluene in a contaminated air stream was investigated over 180 days in a biofilter. A commercially available inorganic/polymeric composite chip with a large void volume (bed porosity > 0.80) was used as a microbial support. Multiple microorganisms including Nitrosomonas and Nitrobactor for nitrogen removal, Thiobacillus thioparus (ATCC 23645) for $H_2S$ removal and Pseudomonas aeruginosa (ATCC 15692), Pseudomonas putida (ATCC 17484) and Pseudomonas putida (ATCC 23973) for toluene removal were used simultaneously. The empty bed residence time (EBRT) ranged from 60 - 120 seconds and the inlet feed concentration was $0.0325\;g/m^3-0.0651\;g/m^3$ for $NH_3$, $0.0636\;g/m^3-0.141\;g/m^3$ for $H_2S$, and $0.0918\;g/m^3-0.383\;g/m^3$ for toluene, respectively. The observed removal efficiency was 2% - 98% for $NH_3$, 2% - 100% for $H^2S$, and 2% - 80% for toluene, respectively. Maximum elimination capacity was about $2.7\;g/m^3$/hr for $NH_3$, > $6.4\;g/m^3$/hr for $H_2S$ and $4.0\;g/m^3$/hr for toluene, respectively. The inorganic/polymeric composite carrier required 40 - 80 days of wetting time for biofilm formation due to the hydrophobic nature of the carrier. Once the surface of the carrier was completely wetted, the microbial activity became stable. During the long-term operation, pressure drop was negligible because the void volume of the carrier was two times higher than the conventional packing materials.

• 한국추진공학회지
• /
• 제21권2호
• /
• pp.32-40
• /
• 2017

탄소섬유/에폭시 복합재의 기공함유율을 정량적으로 평가하기 위한 절차를 제시하였다. 고려한 복합재는 두 종류이며 오토클레이브 공법과 필라멘트와인딩 공법에 의해 제작하였다. 탄소섬유/에폭시 복합재의 기공함유율은 공기 중에서와 물 속에서의 무게에서 구한 복합재의 밀도와 구성재의 밀도, 그리고 산처리법과 고온연소법을 적용하여 구한 무게함유율과 부피함유율을 이용하여 평가하였다. 또한 FE-SEM을 통해 탄소섬유 표면을 관찰하여 복합재 내의 수지 제거 여부도 조사하였다. 연구결과에 따르면 복합재 내의 수지는 산처리법이나 고온연소법을 적용하면 충분히 제거할 수 있으며 구성재의 무게함유율과 부피함유율 그리고 복합재의 기공함유율은 본 연구에서 제시된 절차를 적용하면 정량적으로 평가할 수 있다.

• 상하수도학회지
• /
• 제10권1호
• /
• pp.112-120
• /
• 1996

In this study, the porous glass media was utilized as biomass carrier, and the optimum characteristics of this new media in fixed bed biofilm process were investigated. The characteristics of media considered here are a void volume fraction, a specific surface area, and surface characteristics of media. The effect of surface roughness and material could be clearly demonstrated by the fact that the porous glass media showed a good potential for biofilm development. This might results from the fact that biofilm is initially formed in the surface cavities of the media is protect from the shear effect. Therefore, the microcolonies are not readily detached by the fluid shear. In the steady state, biofilm formation along the packing bed depth was different from media to media. The specific area was also an important factor for the attachment of microorganism on the media surface. The specific area was also an important factor for the attachment of microorganism on the media surface. In the case of porous glass media, about $100m^2/m^3$ was enough to obtain a good organic removal efficiency The organic removal efficiency could be improved by increasing the void volume fraction in the reactor, at least 80% was required to obtain a high removal efficiency and prevent clogging. From the analysis of kinetics study, the yield coefficient, Y, was 0.42 mgMLSS/mgSBOD, endogenous respiration coefficient, ke, was $0.12day^{-1}$ and substrate removel coefficient of Mckinney. km, was $16.8hr^{-1}$ for the porous glass media G-2

• 한국세라믹학회지
• /
• 제39권7호
• /
• pp.693-698
• /
• 2002

반응소결 탄화규소의 잔류 실리콘 양을 최소화하기 위해 3성분계 탄화규소 분말을 혼합하여 최밀 충전 반음소결 탄화규소를 제조하였다. 기지상의 충전밀도 증가로 인해 반응소결 중 실리콘의 불완전 침윤이 발생하였으며, 이로 인한 잔류 기공은 조대 탄화규소 입자의 표면을 따라 존재함을 확인하였다. 불완전 침윤은 승온 중 분해되지 않고 남은 산화물이 실리콘의 용융 온도 이상에서 분해되어 생긴 고립기공에 의한 것으로 확인되었다. 기지상의 표면에 존재하리라 여겨지는 산화물을 제거하기 위해 침윤전 열처리 및 부식처리를 통해 완전침윤을 달성하였다.