• Journal of Drive and Control
• /
• v.9 no.4
• /
• pp.1-7
• /
• 2012

The voice coil linear force motor is a kind of a direct drive motion device that uses a permanent magnetic field and coil winding to produce force. In order to design a voice coil linear force motor, an exact calculations of the required force, the flux density in air gap and the flux pathway are needed. A conventional method can be used usually to calculate the flux density in air gap, but with this method it is needed to find a magnetic circuit revision constant. In this paper a voice coil linear force motor is designed by conventional design method and analyzed by 3D simulation program "Flux". For the prototype linear force motor, the results of the calculated by conventional design method and the analyzed by 3D simulation program are compared with the test result. Finally it is showed that the magnetic circuit revision constant which is found by comparing of the analyzed and the measured data can be used for the design of the voice coil type linear force motor to minimize the trial and error.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1034-1036
• /
• 2004

The most basic form of a direct-drive linear motor is the voice coil motor(VCM). The voice coil motor employs a stationary permanent magnet field assembly in conjunction with a moving coil winding assembly to produce a force proportional to the current applied to the coil. Voice coil motor provide motion capable of extremely fine position sensitivity, limited only by the feedback sensor used to close the control loop. This paper presents dual-servo voice coil motor for improvement of driving range and position resolution. The voice coil motor is a cylindrical shape to improve reliability of a nanoindenter.

• Journal of Magnetics
• /
• v.15 no.3
• /
• pp.143-147
• /
• 2010

Rotary-type voice coil motors are widely used as actuators in hard disk drives. The recent trend toward higher density and smaller form factors in data storage devices requires performance improvement of the voice coil motor. In this study, we introduce a Halbach magnet array to the voice coil motor in order to increase the force generation. The Halbach magnetic circuit outperforms the conventional magnetic circuit due to the confined magnetic flux. To investigate the performance of the Halbach magnetic circuit, we analyze air gap flux density with the various shapes and thickness of the magnets using 3-dimensional finite element analysis. Consequently the optimum shape of the Halbach magnetic circuit is proposed. Simulations and experimental results proved effectiveness of the proposed magnet array in the voice coil motor for a commercial hard disk drive.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.51 no.10
• /
• pp.439-445
• /
• 2002

In this paper force feedback control system is investigated for improving the quality of the haptic feedback in virtual reality applications. We suggested the method of controlling the haptic device and modelling the virtual environment. Haptic device is composed of five bar link structure, voice coil motor, control board, and virtual environment modeling program. We applied voice coil motor in the actuating system for simple structure and easy control. Virtual environment modelling is constructed in PC, and the control signals of the actuators and the encoder data are transferred to the control system through USB. Experiment is performed to evaluate the characteristics of the haptic device.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.577-579
• /
• 2002

Propose of this paper is VCM (voice coil motor) design for application of Nanoindenter, which enable control of extremely small force and displacement. This paper present the VCM shape to produce a very small force by the difference of flux density of lower part from higher one. In wide range of current. VCM produces linear driving force and operate on regular thrust having maximum displacement(100um) was practiced.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1439-1443
• /
• 2007

In this paper, vibration reduction techniques of a voice coil motor (VCM) actuator are presented for AFM imaging system. The damping coefficient of the actuator driven by VCM with a flexure hinge is quite low and it cause the about 30dB peak amplitude response at the resonance frequency. To decrease this peak response, we design and apply elliptical band-stop filters to xy and z axis VCM actuator. Frequency response of each actuator with filter is measured to verify the effect of the filters. As a sensor, capacitive sensor is used. Vibration reduction rate of the xy actuator with the filter is also measured while real AFM scanning condition. As another method, closed loop control with the capacitive sensor is applied to the xy axis actuator to add an electrical damping effect and vibration reduction rate measured. These vibration reduction rates with each method are compared. In the case of z axis actuator, the frequency response of force (gap) control loop is measured. For comparison, the frequency response using a conventional PID controller is also obtained. Finally, the AFM image of a standard grid sample is measured with the designed controller to analyze the effect in the AFM imaging.

• Transactions of the Society of Information Storage Systems
• /
• v.6 no.2
• /
• pp.74-78
• /
• 2010

In this paper, 2-axis driving mechanism, which uses voice coil motor (VCM), is proposed to measure the friction force. The proposed VCM actuator consists of two parts; structural part and magnetic circuit part. Structural part is simplified to perform the friction experiments. Magnetic circuit part is composed of two parts. The experiments are accomplished by changing the mass of moving part. Through the experiments, optimal dimension is selected. Finally, the experimental results are verified and the optimal case is applied to the 2-axis driving mechanism, optical image stabilization actuator.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.750-755
• /
• 2005

This paper proposes a small VCM (Voice coil motor) type actuator using curved suspensions for auto-focusing and zoom motions for mobile information devices. 1'he proposed focusing actuator adopts a nontraditional type of suspension using curved beams in order to extend output displacement within small height restriction. The curved beam is similar to the leaf spring type which is usually used in optical disk drives. In addition, three different materials are considered for the curved suspension model, and Aluminum shows the best dynamic characteristics. The proposed zoom actuator does not use a suspension supporting bobbin but a moving rail and a sloper mechanism by generating rotational force at lens holder. The sensitivity of design parameters on output performance is studied using ANSYS (3D FEM tool). Experiments using a prototype of the proposed actuator model verified the analytical prediction and performance.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.4 no.3
• /
• pp.316-321
• /
• 2004

In this paper, we have developed a new mounting head system for flip chip. The proposed head system consists of a macro/micro positioning actuator for stable force control. The macro actuator provides the system with a gross motion while the micro device yields fine tuned motion to reduce the harmful impact force that occurs between very small sized electronic parts and the surface of a PCB(printed circuit board). In order to show the effectiveness of the proposed macro/micro chip mounting system, we compared the proposed system with the conventional chip mounting head equipped with a macro actuator only. A series of experiments were executed under the mounting conditions such as various access velocities and PCB stiffness. As a result of this study, a satisfactory voice coil actuator as the micro actuator has been developed, and its performance meet well the specifications desired for the design of the chip mounting head system and show good correspondence between theoretical analysis and experimental results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.341-342
• /
• 2013