• International Journal of Highway Engineering
• /
• v.4 no.4 s.14
• /
• pp.53-66
• /
• 2002

Asphalt binder characteristics in asphalt mixture are changed due to aging. However. depending upon aggregate and binder used, asphalt mixture dose not show the same level of stiffness and brittleness under the same ageing level. The factors affecting Physical Properties change of the asphalt binder within aged asphalt concrete are not well known and there is limited study which is dealing with this topic This study dealt with evaluation of physical properties of asphalt binder recovered from the mixtures after short-term and long-term aging. Two asphalts. two aggregates. two gradations and four polymers were used to make 32 mixture combinations. The mixtures were prepared and aged artificially in a forced draft oven. The measured physical properties included absolute viscosity, kinematic viscosity and penetration. Statistical analyses were carried out to find out the factor(s) having a significant effect on change of physical property of asphalt binder due to asphalt mixture aging. The results of study shown that aggregate, gradation and polymer had a significant effect on change of physical properties of asphalt binder.

• Journal of Mechanical Science and Technology
• /
• v.18 no.6
• /
• pp.1036-1041
• /
• 2004

A newly designed pressure-scanning slit viscometer is developed to combine an optical device without refraction while measuring blood viscosity over a range of shear rates. The capillary tube in a previously designed capillary viscometer was replaced with a transparent slit, which is affordable to mount optical measurement of flowing blood cells. Using a pressure transducer, we measured the change of pressure in a collecting chamber with respect to the time, p(t), from which the viscosity and shear rate were mathematically calculated. For water, standard oil and whole blood, excellent agreement was found between the results from the pressure-scanning slit viscometer and those from a commercially available rotating viscometer. This new viscometer overcomes the drawbacks of the previously designed capillary viscometer in the measuring whole blood viscosity. First, the pressure-scanning slit viscometer can combine an optical instrument such as a microscope. Second, this design is low cost and simple (i.e., ease of operation, no moving parts, and disposable).

• Journal of the Korean Ceramic Society
• /
• v.41 no.4
• /
• pp.344-347
• /
• 2004

The influence of spindle immersion depth on the determination of glass melt viscosity was examined in rotating cylinder method. The exact adjustment of spindle immersion depth into soda lime silicate standard glass melts could be peformed by self-constructed electric system. The results showed a slight dependence of viscosity value on the immersion depth change of spindle shaft. The viscosity error per unit length of spindle was 0.4%/mm under the present cylinder dimension.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.10 no.1
• /
• pp.49-74
• /
• 1984

Rheology of gels prepared with stearyl dimethyl benzyl ammonium hectorite (SDBAH) and various polar additives in n-butyl acetate was investigated by measuring the viscosity and rheogram. Including generally recognized polar additives, additional studies on the rheogram and viscosity were made with ether-type methyl cellosolve and carbitol, with dimethyl sulfoxide (DMSO) having sulfonyl group, and furthermore with above-mentioned polar additives containing small quantity of water, It was observed that molecular size, dipole moments and dielectric constants of polar additives had a great influence on viscosity increase and rheology of SDBAH gel, and the increase of SDBAH interlayer spacing was important factor in gel formation and viscosity change. It was also shown that thixotropy effect was increased with the increase of polar additive concentration, finally changed to rheopexy from thixotropy as the concentration of polar additives was increased more than about 40% of SDBAH weight. In addition thixotropy changed to rheopexy as the increase of shear rate. It was further found that the aqueous solutions of polar additives (water content, 5-25%) had more effects on rheology than additives without water, and particularly 95clo DMSO solution was the most effective. And the optimum concentration of polar additives showing maximum viscosity in the same SDBAH concentration system was examined.

• Korea-Australia Rheology Journal
• /
• v.12 no.1
• /
• pp.77-81
• /
• 2000

Rheological behavior of thermoset/thermoplastic blends of epoxy/polyethersulphone (PES) was monitored during curing of the epoxy resin. During the isothermal curing of the mixture, a fluctuation in viscosity just before the abrupt viscosity increase was observed. This fluctuation is found to be due to the phase separation of PES from the matrix epoxy resin during the curing. The experimentally observed viscosity fluctuation is simulated with a simple two phase suspension model in terms of the increase in domain size. The viscosity profiles obtained experimentally at different isothermal curing temperatures are in good agreement with the predictions from the simple model taking into account the viscosity change due to the growth of PES domain and the network formation of the epoxy matrix.

• Macromolecular Research
• /
• v.17 no.12
• /
• pp.943-949
• /
• 2009

A highly dispersed W/O emulsion of silicone oil (cyclomethicone)/water system was prepared with a nonionic surfactant. The surface and interfacial tension between the oil and water were characterized in terms of the droplet size distribution and viscosity change of the emulsion. When the dispersed phase concentration was relatively high, the viscosity of the emulsion was rapidly increased and the droplet size of the emulsion was decreased. The rheological behavior of the emulsion system showed non-Newtonian and shear thinning phenomena depending upon the content of the dispersed phase. The droplet size of the emulsion was decreased with increasing surfactant content and water concentration. The relative viscosity of the emulsion was better predicted with the Choi-Schowalter model than with the Taylor model. The value of the complex modulus increased with increasing surfactant concentration. The linear viscoelastic region was expanded with a dispersed phase concentration. According to the change in the viscosity, the behavior was classified into three distinct regions: [I] linear viscoelastic, [II] partially viscoelastic, and [III] viscous. The creep/recovery behaviors in each region were characterized.

• Korea-Australia Rheology Journal
• /
• v.16 no.4
• /
• pp.175-182
• /
• 2004

Colloidal coating solution was prepared to enhance the hydrophilic property of the film surface. Water and ethanol were used as the dispersion media and (glycidoxypropyl) trimethoxysilane (GPS) as a binder in the colloidal silica coatings. Ethylene diamine was added to the colloidal silica solution as the curing agent. The colloidal silica solution was regarded as a hard-sphere suspension model with low volume fraction of the silica particles. Rheological properties of the silica suspensions modified with GPS have been investigated as a function of pH and concentration. The acidic solution showed high viscosity change by fast hydrolysis reaction and adsorption of the organic binders on the surface of silica particles. However, the hydrolysis was slow at the basic condition and the binders combined with themselves by condensation. The viscosity change was smallest at pH 7. The viscosity increased with the curing time after adding ethylenediamine, and the increase of viscosity at low pH was higher than that at high pH. The hydrophilic properties of the coating film were investigated by the contact angle of water and film surface. The smallest contact angle was shown under the strong acidic condition of pH 2.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.414-423
• /
• 2006

Many construction projects adopt grouting technology to prevent the leakage of groundwater or to improve the shear strength of the ground. Recognition as a feasible field procedure dates back to 1925, Since then, developments and field use have increased rapidly. According to improvement of grout materials, theoretical study on grout penetration characteristics is demanded. Fluid of grout always tends to flow from higher hydraulic potential to lower and the motion of grout is also a function of formation permeability. Viscosity of grout is changed by chemical action while grout moves through pores. Due to the increment of viscosity, permeability is decreased. Permeability is also reduced by grout particle deposits to the soil aggregates. In this thesis, characteristics of new cement grout material that is developed recently is studied: injectable volume of new grout material is tested in two different sizes of sands, and the method to calculate injectable volume of grout is suggested with consideration of change in viscosity and clogging phenomena. The calculated values are compared with injection test results. Viscosity of new grout material is found to be an exponential function of time. And lumped parameter $\theta$ of new grout material to be used for assessing deposition characteristics is estimated by comparing deposit theory with injection test results considering different soil types and different injection pressure.

• Journal of Sensor Science and Technology
• /
• v.17 no.4
• /
• pp.289-294
• /
• 2008

The purpose of this study is to materialize the viscosity sensor by using the SH-SAW sensor of which the center frequency is operated at higher than 50 MHz. In order to measure the viscosity, SAW sensor of which the center frequency is operated at 100 MHz is developed. By using the developed sensor, phase shift, delay time, insertion loss, and frequency variation are measured at different viscosity. The result shows that the phase shift difference between the viscosity variations is such that the difference between the distilled water and the 100 % glycerol solution is approximately $45^{\circ}$, the change of the insertion loss is approximately 9 dB, and the difference of frequency variation is approximately 5.9 MHz. Therefore, it is shown that viscosity of unknown solution can be measured with the surface acoustic wave sensor.

• Journal of Korean Society of Water and Wastewater
• /
• v.30 no.6
• /
• pp.737-744
• /
• 2016

The investigation of effects on fouling propensity with various viscosity of feed solutions would be better understanding for forward osmosis (FO) performance since the fouling propensity was directly influenced with solution viscosity. Therefore, this study was focused on the FO fouling with model foultants (humic acid, alginate) by altering solution viscosity with change of ionic strength (I.S) and $Ca^{2+}$ concentrations. In the comparison between humic acid and alginate, as expected, the alginate generally caused more severe fouling (almost 35.8 % of flux reduction) based on the solution characteristics (high viscosity) and fouling patterns (coil and gel layer). However, interesting point to note is that the fouling propensity of alginate was more severe even though it was applied with low viscosity of feed conditions (I.S = 20 mM, $Ca^{2+}=1mM$). This might be due to that crossed linked gel layer of alginate on the FO membrane surface could be best formed in the condition of $Ca^{2+}$ presence and higher I.S, and that is more dominant to fouling propensity than the low viscosity of feed solutions.