• Journal of the Korea Institute of Military Science and Technology
• /
• v.17 no.3
• /
• pp.318-326
• /
• 2014

The Shipyard Test of Naval Combat System depends on external factors, such as weather conditions and availability of its sensor-weapon, due to the need of on-board sensor-weapon during the test. This paper suggests the Supportive Equipment using virtual simulator for Shipward Test, in case of the unavailability of the on-board sensor-weapon or the test support force(aircraft, surface ship etc.), to pre-check the functions of the combat system as well as to prepare the Shipyard Test. To mock the real sensor-weapon functions as similar as possible, the Supportive Equipment for Shipyard Test was verified by the Verification and Validation process, which is usually performed while developing models in the Modeling & Simulation field.

• Journal of Advanced Navigation Technology
• /
• v.27 no.6
• /
• pp.788-797
• /
• 2023

In this paper, we introduced a test environment to test a vision-aided navigation system, as an alternative navigation system when global positioning system (GPS) is unavailable, for vertical take-off and landing (VTOL) unmanned aerial system. It is efficient to use a virtual environment to test and evaluate the vision-aided navigation system under development, but currently no suitable equipment has been developed in Korea. Thus, the proposed test environment is developed to evaluate the performance of the navigation system by generating input signal modeling and simulating operation environment of the system, and by monitoring output signal. This paper comprehensively describes research procedure from derivation of requirements specifications to hardware/software design according to the requirements, and production of the test environment. This test environment was used for evaluating the vision-aided navigation algorithm which we are developing, and conducting simulation based pre-flight tests.

• Journal of Drive and Control
• /
• v.10 no.1
• /
• pp.7-13
• /
• 2013

Port size 80mm or above large-flow type solenoid valves are extensively used in dust collector and power plants. These multi-stage solenoid valve have few problem. first, multi-solenoid valves are almost depend on imports and there are weak in the brine environment and the low energy efficiency. Because these problem, increased the necessity of research on the development of large flow and high pressure type solenoid valves. In this study, describe the design method of multi-stage solenoid test bench and confirm the influence valve performance on several parameter such as diaphragm orifice diameter. At first, each part has modeled by AMESim simulation tool and combining them. This AMESim virtual multi-stage solenoid valve found influence valve performance on the valve parameter. Finally developed the multi-stage solenoid valve and verified that performance on experimental result.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.25 no.7
• /
• pp.406-412
• /
• 2013

A hybrid heat pump is under development with the goal of utilizing 120% of primary energy resources. A plate heat exchanger is added between the compressor and air-cooled condenser of an ordinary heat pump to heat water. For successful operation of the heat pump, it is necessary to develop a control algorithm under various operating conditions. As a virtual test bed for that purpose, a dynamic model has been developed, to simulate its dynamic behavior. It was modeled in transient one-dimensions, with varying phase lengths considered. The model was implemented in Matlab and Simulink. Simulation results were effectively applied to design a control algorithm. They also provided physical insight into how to design and operate the system.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.107-110
• /
• 1999

The purpose of this research is for the development of a new type forging equipment H.C.G(Hyundai Continuous Grain-flow) by using two virtual build-up tools rigid viscoplastic FEM and downsized plasticine experiment. This forging equipment consists of consecutive horizontal and vertical pressure while the traditional forging method consists of only vertical pressure. Using this method high quality crankshafts can be forged as it can maintain a continuous grain flow. The factors considered in the development of equipment are die geometry for flawless deformed shape die reaction forces stress/strain distributions and continuous material flow. We carried out several numerical simulations and downsized plasticine experiments for the proper design of the forging equipment. The validity of those simulation results is confirmed by checking with the actual test results. Based on these simulation results the proper design of the H.C.G for ging equipment is enabled.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.5C no.1
• /
• pp.14-17
• /
• 2005

In this paper, an automated methodology for generating model parameters considering real manufacturing processes is presented with verified results. In addition, the outcomes of applications to the next generation of flash memory devices using the parameters calibrated from the process specification decision are analyzed. The test vehicle is replaced with a well-calibrated TCAD simulation. First, the calibration methodology is introduced and tested for a flash memory device. The calibration errors are less than 5% of a full chip operation, which is acceptable to designers. The results of the calibration are then used to predict the I-V curves and the model parameters of various transistors for the design of flash devices.

• Transactions of Materials Processing
• /
• v.8 no.3
• /
• pp.237-244
• /
• 1999

The purpose of this research is for the development of a new type forging equipment. H.C.G.(Hyundai Continuous Grain-Flow), by using two virtual build-up tools, rigid viscoplastic FEM and downsized plasticine experiment. This forging method consists of only vertical pressuree. Therefore, high quality crankshafts can be forged with this method as it can maintain a continuous grain flow. The factors considered in the development of equipment are die geometry for flawless deformed shape, die reaction forces, stress/strain distributions and continuous material flow. We carried out several numerical simulations and downsized plasticine experiments for the proper design of the forging equipment. The validity of those simulation results is confirmed by checking with the actual test results. Based on these simulation results, the proper design of the H.C.G. forging equipment is enabled.

• Proceedings of the Korean Institute of Interior Design Conference
• /
• 2008.05a
• /
• pp.179-183
• /
• 2008

A variety of design processes from 2D graphic to 3D models are meeting improved consumers' confidence of modern clients. However, the current design methods are limited to meet consumers' needs and express a design concept what a designer wants to show. Therefore the study here tries a test of hybrid space simulation combined with previous models and digital media technology, which can be used for multiple contents. The study can contribute to suggesting virtual space simulation that can help clients' spatial understanding in this media era and deliver emotional language of designers as well by utilizing the strong point of multi-sensible media.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.10a
• /
• pp.119-131
• /
• 1997

Ball type automatic balancer is used to reduce the vibration caused by unbalance of rotor. In this study, A analytic modeling of a front loaded washing machine with ball type automatic balancer has been suggested theoretically and ADAMS has been used to analyze the dynamic characteristics of automatic balancer. It is found from simulation and experimental results that the automatic balancer suppress the steady state vibration of the washing machine effectively. The test results match well with the simulation results of ADAMS, thereby the dynamic model of ADAMS can be used as virtual prototype to predict the vibration characteristics which could be changed by the modification of design variable and can reduce the design cycle sharply. To maximize the balancing effect of automatic balancer, the friction between balls and race and the deviation between geometric center and rotation center of drum need to be minimized and the optimum design for the stiffness of flange shaft and the angular acceleration of drum should be achieved.

• The Journal of Korean Academic Society of Nursing Education
• /
• v.30 no.1
• /
• pp.29-38
• /
• 2024

Purpose: This study aimed to investigate student nurses' satisfaction by type of clinical practicum and to determine predictors of clinical competence in pediatric nursing. Methods: A total of 189 Junior and Senior student nurses across seven colleges in the Busan Metropolitan City were enrolled in the study. The participants completed a structured questionnaire containing items about their learning satisfaction with different types of pediatric nursing practicums and their clinical competence. Data were analyzed using the mean, standard deviation, independent t-test, ANOVA, and multiple regression analysis. Results: Regarding satisfaction with each type of clinical practicum, the mean satisfaction score (out of 10) was 8.18±2.26 for on-site clinical rotations and 7.35±2.20 for alternative practicums. Among the different types of alternative practicum approaches, those with a satisfaction score of 7 or higher included fundamental nursing skills, watching videos, simulation etc., while those with a satisfaction score of less than 6 were virtual simulation and problem-based learning. The predictors of clinical competence in pediatric nursing were learning satisfaction with practice, school year, and alternative practicum, accounting for 35.0% of the variance in clinical competency. Conclusion: It would be helpful to combine on-site clinical rotations with alternative practicum approaches and to develop various alternative practice programs using simulation practice, virtual reality, immersive interactive systems, and standardized patients to enhance students' clinical competency.