• 드라이브 ㆍ 컨트롤
• /
• 제13권2호
• /
• pp.19-25
• /
• 2016

Recently, drivers have begun to regard comfort in the cabin as one of the most important factors in construction equipment like forklifts. Accordingly, it has become more important to design a forklift cabin with a better sound quality as well as lower sound level, which can make a driver more comfortable. In this paper, the correlation between subjective evaluation and Zwicker's sound quality index was analyzed through a blind test by a few workers in forklifts and other construction equipment in several countries. Correlation analysis showed that Loudness and Sharpness were ranked in sequence, and tendencies were different from country to country. Also, contribution analysis for Loudness and Sharpness using operational transfer path analysis (OTPA), which is widely used in the field of noise, vibration, and harshness (NVH), was performed. However, Loudness and Sharpness cannot be used with OTPA directly because there are no linear relationships between the sources and receivers. In this paper, both are calculated by applying the DIN 45631 method with a contribution rate (%) of 1/3 Octave Sound Pressure Level by OTPA method in addition to considering spectral masking.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2004년도 제29회 KOSCI SYMPOSIUM 논문집
• /
• pp.206-212
• /
• 2004

It is necessary to consider the stability, economic environmental-friendly problems by the development of the road, supply of the automobile, environmental problem as designing the exhaust system. To reduce the noise and the vibration of the automobile, it is needed to consider the pulsation noise, air current noise, vibration of air pipe which generate the intake and exhaust noise of the automobile. Moreover, the discharge sounds, intake sound, radiation sound, transmitted sound are occurred. To reduce this influence, the variable valve is needed and to control these factors, path transformation muffler and active type muffler are needed. While engine efficiency could be reduced with this transformationand resistance by the pressure, thermal property. In this study, how to design exhaust systems yielding higher condversion efficiency, lower backpressure and optimize the performance. this study is recommended for exhaust system and designers and engineers involved in SI engine exhaust system and it will furnish information for you to design more efficient.

• 한국소음진동공학회논문집
• /
• 제20권8호
• /
• pp.734-741
• /
• 2010

In this paper, an intake RCV system for low noise turbo engine was developed through optimization process of a geometric path of compressor housing and an open rate of recirculation valve. At first, the critical customer requirement from voice of customer was defined and quality function deployment of an intake RCV system was executed. And then, the renovative concept design using pugh matrix method was selected as final concept for satisfaction of requirement. Simultaneously, system analysis was carried by function diagram and fishbone diagram. Next, control factors and levels for the optimal design were performed. And, the optimal design of an intake RCV system was studied using design of experiment. Conclusively, we achieved not only cancellation tip-out noise at the driving condition but also improvement of NVH commodity through optimization process of an intake RCV system, which is optimal configuration of compressor housing and recirculation valve.

• 한국정밀공학회지
• /
• 제22권4호
• /
• pp.76-83
• /
• 2005

With the acceleration of the miniaturization of products, especially in recent years, machining technologies for these products is in need of improvement. Conventional technologies have limitations in realizing the miniaturization due to the downsizing effects of the tools, which lack sufficient cutting stiffness during machining. The application of ultrasonic vibration is one of the most useful solutions in dealing with the problem. This study focused on the difference of ultrasonic drilling from conventional one in geometrical machining mechanism and the corresponding machining results. In detailed, some mathematical equations for drill cutting edge paths during drilling were extracted and new method to find uncut chip thickness from above equations was suggested. The experiments were carried out through the comparison between the results (disposed chips and internal surface states of holes) of conventional drilling and those of ultrasonic drilling. It was determined that the geometrical paths of cutting edges and analyzed uncut chip thickness agree with the appearance of disposed chips. Furthermore, the change in tool path by ultrasonic vibration resulted in the improvement of surface statement.

• 한국소음진동공학회논문집
• /
• 제15권1호
• /
• pp.53-62
• /
• 2005

This study presents the NDE (non-destructive evaluation) technique for detecting the loosened bolts on joint steel structures on the basis of TOF (time of flight) and amplitudes of Lamb waves. Probabilistic neural network (PNN) technique which is an effective tool for pattern classification problem was applied to the damage estimation using PZT induced Lamb waves. Two kinds of damages were introduced by dominant damages (DD) which mean loosened bolts within the Lamb waves beam width and minor damages (MD) which mean loosened bolts out of the Lamb waves beam width. They were investigated for the establishment of the optimal decision boundaries which divide each damage class's region including the intact class. In this study, the applicability of the probabilistic neural networks was identified through the test results for the damage cases within and out of wave beam path. It has been found that the present methods are very efficient and reasonable in predicting the loosened bolts on the joint steel structures probabilistically.

• 한국소음진동공학회논문집
• /
• 제18권3호
• /
• pp.284-292
• /
• 2008

The active control technique mostly uses the least-mean-square(LMS) algorithm, because the LMS algorithm can easily obtain the complex transfer function in real-time, particularly when the Filtered-X LMS(FXLMS) algorithm is applied to an active noise control(ANC) system. However, FXLMS algorithm has the demerit that stability of the control is decreased when the step size become larger but the convergence speed is faster because the step size of FXLMS algorithm is fixed. As a result, the system has higher probability which the divergence occurs. Thus the Co-FXLMS algorithm was developed to solve this problem. The Co-FXLMS algorithm is realized by using an estimate of the cross correlation between the adaptation error and the filtered input signal to control the step size. In this paper, the performance of the Co-FXLMS algorithm is presented in comparison with the FXLMS algorithm. Simulation and experimental results show that active noise control using Co-FXLMS is effective in reducing the noise in duct system.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.737-742
• /
• 2007

The method of the reducing duct noise can be classified by passive and active control techniques. However, passive control has a limited effect of noise reduction at low frequencies (below 500Hz) and is limited by the space. On the other hand, active control can overcome these passive control limitations. The active control technique mostly uses the Least-Mean-Square (LMS) algorithm, because the LMS algorithm can easily obtain the complex transfer function in real-time particularly when the Filtered-X LMS (FXLMS) algorithm is applied to an active noise control (ANC) system. However, the convergence performance of the LMS algorithm decreases slightly so it may delay the convergence time when the FXLMS algorithm is applied to the active control of duct noise. Thus the Co-FXLMS algorithm was developed to improve the control performance in order to solve this problem. The Co-FXLMS algorithm is realized by using an estimate of the cross correlation between the adaptation error and the filtered input signal to control the step size. In this paper, the performance of the Co-FXLMS algorithm is presented in comparison with the FXLMS algorithm. Simulation results show that active noise control using Co-FXLMS is effective in reducing duct noise.

• 한국소음진동공학회논문집
• /
• 제21권1호
• /
• pp.3-8
• /
• 2011

This paper introduces a robot eye module, of which two degree-of-freedom motions, i.e. panning and tilting, are driven by a pair of wires. The main feature of the module is that each wire can generate push-pull motion without buckling. It is thanks to a Teflon tube which guides the path of the moving wire. End points of the tube and wire have pivot elements so that a smooth push-pull motion is produced even when the end point of wire is moved by eye rotation. This mechanism helps the eye module to be very compact. In this paper, the structure of the robot eye module is introduced in detail, and the required motor angles for a certain direction of eye line are investigated analytically and experimentally.

• 한국소음진동공학회논문집
• /
• 제21권1호
• /
• pp.81-88
• /
• 2011

The method is introduced for estimating the noise source contribution on the noise of PDP TV in a multiple-input system where the input sources may be coherent with each other. By the coherence function method, it is found that the biggest part of the noise source in the PDP TV noise is generated by the PCB boards which consume high power and produce high heat. This analysis is modeled as three-input/single-output system because the noise is generated by three main boards, X-board, Y-board, SMPS that are located close to each other. The coherence function method is proved to be useful tool for identifying of noise source. In this study, Transfer Path Analysis using MDSA is implemented to determine the quantitative noise contribution of each board for PDP TV with the rear case closed and with the rear case open. And the possibility of noise reduction is confirmed through the experimental method that isolates the most contributing board by adding sound-absorbing materials to it.

• 한국소음진동공학회논문집
• /
• 제24권8호
• /
• pp.628-635
• /
• 2014

The procedure to estimate the sources of noise and vibrations in a typical drum-type washing machine was presented. The sources should be identified to predict the radiated noise with computational model of structure. Source identification techniques based on singular decomposition were implemented using the measured signals of accelerometers and microphones. The finite element analysis and indirect boundary element analysis were implemented to predict the structural vibrations and the acoustic pressures at the field points. The predicted results by only structural sources were compared with those by both structural and acoustical sources. It was verified that not only the structural-borne source but also air-borne source should be considered to predict the radiated noise with better accuracy. The contribution analysis with respect to the transfer path was also preformed.