• Geomechanics and Engineering
• /
• 제16권4호
• /
• pp.399-413
• /
• 2018

This paper addresses the issue of field measurement of excavation damage zone (EDZ) and its numerical simulation method considering both excavation unloading and blasting load effects. Firstly, a 2000 m-deep rock cavern in China is focused. A detailed analysis is conducted on the field measurement data regarding the mechanical response of rock masses subjected to excavation and blasting operation. The extent of EDZ is revealed 3.6 m-4.0 m, accounting for 28.6% of the cavern span, so it is significantly larger than rock caverns at conventional overburden depth. The rock mass mechanical response subjected to excavation and blasting is time-independent. Afterwards, based on findings of the field measurement data, a numerical evaluation method for EDZ determination considering both excavation unloading and blasting load effects is presented. The basic idea and general procedures are illustrated. It features a calibration operation of damage constant, which is defined in an elasto-plastic damage constitutive model, and a regression process of blasting load using field blasting vibration monitoring data. The numerical simulation results are basically consistent with the field measurement results. Further, some issues regarding the blasting loads, applicability of proposed numerical method, and some other factors are discussed. In conclusion, the field measurement data collected from the 2000 m-deep rock cavern and the corresponding findings will broaden the understanding of tunnel behavior subjected to excavation and blasting at great depth. Meanwhile, the presented numerical simulation method for EDZ determination considering both excavation unloading and blasting load effects can be used to evaluate rock caverns with similar characteristics.

• International Journal of Automotive Technology
• /
• 제7권7호
• /
• pp.847-852
• /
• 2006

A fitting process carried out in the automobile transmission assembly line is classified into three classes; heat fitting, press fitting, and their combined fitting. Heat fitting is a method that applies heat in the outer diameter of a gear to a suitable range under the tempering temperature and assembles the gear and the shaft made larger than the inner radius of the gear. Its stress depends on the yield strength of a gear. Press fitting is a method that generally squeezes gear toward that of a shaft at room temperature by a press. Another method heats warmly gear and safely squeezes it toward that of a shaft. A warm shrink fitting process for an automobile transmission part is now gradually increased, but the parts (shaft/gear) assembled by the process produced dimensional change in both outer diameter and profile of the gear so that it may cause noise and vibration between gears. In order to solve these problems, we need an analysis of a warm shrink fitting process in which design parameters such as contact pressure according to fitting interference between outer diameter of a shaft and inner diameter of a gear, fitting temperature, and profile tolerance of gear are involved. In this study, an closed form equation to predict the contact pressure and fitting load was proposed in order to develop an optimization technique of a warm shrink fitting process and verified its reliability through the experimental results measured in the field and FEM, thermal-structural coupled field analysis. Actual loads measured in the field have a good agreement with the results obtained from theoretical and finite element analysis and also the expanded amounts of the outer diameters of the gears have a good agreement with the results.

• 한국강구조학회 논문집
• /
• 제10권4호통권37호
• /
• pp.577-587
• /
• 1998

본 연구에서는 열차하중이 강합성형 철도교의 동적응답에 미치는 영향을 연구하였다. 2개의 I-거더와 가로보로 구성된 판형교는 판요소와 공간뼈대요소를 이용하여 모델링하였으며, 상판과 주형의 offset은 완전합성을 가정하여 구속방정식을 이용하여 연결하였으며 트랙구조는 고전적인 탄성지반위의 보 이론을 사용하여 이상화하였다. 2PC+2MT+161T로 구성된 TGV열차의 수직처짐과 피칭회전을 고려한 2차원 수치모델을 개발하였다. 또한, 속도의존적 제동함수를 사용하여 열차의 제동을 고려하였다. 이동열차하중에 의한 교량의 동적거동 파악을 위하여 교량의 고유진동수 변화, speed parameter, 차량모델링 방법, 열차의 제동 등에 대한 매개변수연구를 수행하였다.

• Tribology and Lubricants
• /
• 제31권1호
• /
• pp.6-12
• /
• 2015

This paper investigates the stick-slip characteristic of magnetorheological elastomer (MRE) between an aluminum plate and the surface of the MRE. MRE is a smart material and it can change its mechanical behavior with the interior iron particles under the influence of an applied magnetic field. Stick-slip is a movement of two surfaces relative to each other that proceeds as a series of jerks caused by alternate sticking from friction and sliding when the friction is overcome by an applied force. This special tribology phenomenon can lead to unnecessary wear, vibration, noise, and reduced service life of work piece. The stick-slip phenomenon is avoided as far as possible in the field of mechanical engineering. As this phenomenon is a function of material property, applied load, and velocity, it can be controlled using the characteristics of MRE. MRE as a soft smart material, whose mechanical properties such as modulus and stiffness can be changed via the strength of an external magnetic field, has been widely studied as a prospective replacement for general rubber in the mechanical domain. In this study, friction force is measured under different loads, speed, and magnetic field strength. From the test results, it is confirmed that the stick-slip phenomenon can be minimized under optimum conditions and can be applied in various mechanical components.

• Tribology and Lubricants
• /
• 제23권3호
• /
• pp.130-133
• /
• 2007

Fuel cladding tubes in nuclear fuel assembly are held up by supporting grids because the tubes are long and slender. Fluid flows of high-pressure and high-temperature in the tubes cause oscillating motions between tubes and supports. This is called as FIV (flow induced vibration), which causes fretting wear in contact parts of tube and support. The fretting wear of tube and support can threaten the safety of nuclear power plant. Therefore, a research about the fretting wear characteristics of tube-support is required. The fretting wear tests were performed with supporting grids and cladding tubes, especially after corrosion treatment on tubes, in water. The tests were done using various applied loads with fixed amplitude. From the results of fretting tests, the wear amounts of tube materials can be predictable by obtaining the wear coefficient using the work rate model. Due to stick phenomena the wear depth was changed as increasing load and temperature. The maximum wear depth was decreased as increasing the water temperatures. At high temperatures there are the regions of some severe adhesion due to stick phenomena.

• Tribology and Lubricants
• /
• 제24권3호
• /
• pp.129-132
• /
• 2008

Fuel cladding tubes in nuclear fuel assembly are held up by supporting grids because the tubes are long and slender. Fluid flows of high-pressure and high-temperature in the tubes cause oscillating motions between tubes and supports. This is called as FIV (flow induced vibration), which causes fretting wear in contact parts of tube and support. The fretting wear of tube and support can threaten the safety of nuclear power plant. Therefore, a research about the fretting wear characteristics of tube-support is required. The fretting wear tests were performed with supporting grids and cladding tubes, especially after corrosion treatment on tubes, in water. The tests were done using various applied loads with fixed amplitude. From the results of fretting tests, the wear amounts of tube materials can be predictable by obtaining the wear coefficient using the work rate model. Due to stick phenomena the wear depth was changed as increasing load and temperature. The maximum wear depth was decreased as increasing the water temperatures. At high temperatures there are the regions of some severe adhesion due to stick phenomena.

• 한국포장학회지
• /
• 제13권1호
• /
• pp.25-28
• /
• 2007

Physical damage on fruits and vegetables caused by shock degrades the value of product in the fresh market. In order to design a product/package system to protect the product, the peak acceleration or G force to the product that causes shock damage needs to be determined. Shock cushion packaging is applied to protect goods of all kinds. It can be adapted in their shape to any product to be packed, so that its shock absorbing properties is determined by geometry of the product. The shape of a cushion can be adapted to the expected shock loads. To analyze the response properties of cushion materials for packaging of the pears for optimum packaging design during transportation, shock tests were carried out. Shock acceleration that is happened in pears were appeared very high by $25{\sim}30G$ in the input shock acceleration of 14.1618 G that was measured in transportation road. This means that the pears receive the shock acceleration more than maximum double itself and the damage by this can happen and the shock acceleration increase in case use PE tray cup and PE net in fruits, the use of corrugated fiberboard pad may become one method that it can reduce the damage by the shock in packaging of fruits.

• 대한기계학회논문집A
• /
• 제34권10호
• /
• pp.1339-1344
• /
• 2010

모달중첩법은 구조물의 진동특성을 고려하여 내구수명을 평가할 수 있는 내구해석 기법이다. 본 논문에서는 모달중첩법과 유사하면서도 다물체 동역학 해석시 모달좌표를 직접 계산하여 전체적인 해석시간을 줄일 수 있는 모달응력 회복법을 이용한 내구해석 기법의 타당성에 대하여 검토하였다. 이를 위해 자동차 부품 중 대표적으로 동특성을 고려해야 하는 토션빔 액슬에 대하여 모달응력 회복법을 이용한 내구해석 및 시험을 실시하였다. 해석결과는 시험결과와 취약위치, 내구수명 등이 양호한 일치 결과를 나타내었다. 따라서 모달응력 회복법을 이용한 내구해석 기법은 다양한 구조물의 동특성을 반영한 내구수명 평가에 적용될 수 있을 것이다.

• 한국강구조학회 논문집
• /
• 제22권6호
• /
• pp.599-608
• /
• 2010

트러스의 상현재와 콘크리트 슬래브가 합성 거동하는 합성 트러스는 장스팬에 경제적인 구조시스템임에도 불구하고 현재 국내에서 설계되는 대부분의 트러스 보는 바닥슬래브와의 합성효과를 전혀 고려하지 않고 설계되고 있다. 슬래브와 트러스 보의 합성효과를 고려할 경우에는 단순히 고정하중으로 취급되던 슬래브를 구조체로서 활용할 수 있으므로 구조 재료를 매우 효율적으로 활용할 수 있게 되고 구조체의 강성이 증가하게 되므로 장스팬 설계의 중요 변수인 사용성 측면에서도 상당한 이점을 확보할 수 있게 된다. 이와 더불어 슬래브 하부에 다양한 설비 시설을 위한 공간이 확보되므로 보의 춤이 깊어지는데 대한 단점을 상당부분 상쇄할 수 있게 된다. 본 연구는 합성 트러스 시스템을 개발함에 있어 국내 현실을 충분히 반영하여 국내 설계 및 시공 현장에서 바로 적용하기 위한 초기단계의 연구로서 실험과 수치해석을 통해 스터드 커넥터의 유 무에 따른 합성 트러스의 역학적 거동 특성을 평가하기 위한 것에 목적을 두고 있다.

• 한국전산구조공학회논문집
• /
• 제29권3호
• /
• pp.261-268
• /
• 2016

동조액체감쇠기(TLD)는 에너지 소산장치로써 구조물의 동적응답을 제어하기 위해 개발되었다. TLD는 풍하중에 의한 구조물의 응답을 제어에 매우 효과적임을 보여줬다. 그러나 TLD가 설치된 구조물의 지진응답의 제어에 대해서는 충분한 연구가 이뤄지지 않았다. 이 연구의 목적은 TLD가 설치된 구조물에 여러 동조비와 질량비를 대입하여 지진에 대한 TLD의 성능을 도출하는 것이다. 이러한 목적을 위해, 수치해석 연구가 실시되며, 다른 토양 조건 또한 고려되었다. 그 결과 지진하중에 대한 TLD의 성능은 구조물의 고유주기, 감쇠비에 따라 다르게 나타났다. 또한 TLD의 동조비 다르게 나타남을 알 수 있었다.