• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.904-907
• /
• 2002

Optical disk drive device is improved in rotating speed for faster data reading. In the case of CD-ROM, rotating speed is over 10000 rpm in the practical use. As a result of high rotating speed, unexpected effects as like increasing disk fluctuation and acoustic noise are raised by the air friction on the rotating disk and the eccentricity of rotating parts. The overall acoustic noise of running CD-ROM could be classified into two different characterized noise. The first is the structural-borne noise which is generated from vibrating solid body. By the reason, the signal of structural borne noise has very similar to the signal of surface vibrating one. It has dense noise energy at specific frequency region. The other is the air-borne noise which is generated from turbulence or vortex caused by friction between disk and air. The signal of air-borne noise has no dominant peak point at acoustic pressure-frequency domain. The noise energy is widely distributed while comparatively high and large frequency region. The structural-borne noise could be reduced by reducing vibration of structure and in addition it's target reducing frequency is narrow. However the air-borne noise reduction is effectively needed of enclosing method for the noise source located near the disk surface because it is difficult to define target frequency point. In this study, the acoustic noise at driving CD-ROM is classified by the sides of it's character and tried to reduce the overall acoustic noise.

• 화약ㆍ발파
• /
• 제36권4호
• /
• pp.48-61
• /
• 2018

본 사례연구는 성남시 분당구에 위치한 한국가스공사(KOGAS) 분당사옥 건물의 발파해체 프로젝트에 관한 것이다. 대상건물은 긴 경간을 갖는 보 구조물이라는 특징 때문에 프로젝트 초기에는 잭 서포트를 이용한 기계식 해체공법이 고려되었다. 하지만 과도한 보강비용과 안전상의 불확실성, 그리고 공사기간의 장기화 우려 때문에 발파해체공법을 대안공법으로 적용하였다. 폭약의 기폭순서는 붕괴과정 중에 주변의 건물 및 시설물 방호를 목적으로 정교하게 설계하였으며, 대상건물은 왼쪽 전방을 향해 붕괴되도록 유도하였다. 1층, 2층 및 5층에 위치한 발파기둥들에 설치된 폭약을 순차적으로 기폭시키는 데에는 총 550개 이상의 전자뇌관(Unitronic 600)이 사용되었다. 분진발생을 저감하기 위해 각각의 발파대상 기둥과 바닥에는 작은 물주머니와 큰 물주머니를 각각 설치하였다. 이와 같이 본 프로젝트에서는 대상건물의 발파해체 시에 발생될 것으로 예상되는 소음, 분진 및 충격진동을 경감시키기 위해 총체적인 노력을 경주하였다.

• 대한기계학회논문집A
• /
• 제39권4호
• /
• pp.415-421
• /
• 2015

본 연구는 햅틱 진동자의 개발과정에 있어 성능인자의 단계별 설정절차와 성능 및 소형화를 위한 자석의 착자방법에 대한 연구를 수행하였다. 착자방법에 대한 연구는 수평착자와 수직착자의 구성방법에 따른 전자기력을 비교분석하여 수행하였으며, 수행결과 수평착자가 우수한 것으로 나타났다. 시스템적 설계 절차로는 제품의 특성으로부터 설계 인자를 설정하는 단계적 절차를 구성하여 시작품을 제작하고 시험을 통하여 검증하였다. 해석적 방법에서는 진동응답 특성 해석과 전기장의 해석을 독립적으로 수행하였으며, 시험결과와의 검증을 통해 잘 일치하는 결과를 도출하였다. 제품신뢰성 확보를 위한 신뢰성 기반 설계인자는 스프링 높이, 용접 위치, 코일의 위치로 선정하였다. 그리고 설계 인자에 따른 전자기장 민감도 및 성능 변화를 분석하였고 이를 바탕으로 신뢰성 기반의 고성능 햅틱 진동자를 구현할 수 있도록 설계방법을 제시하였다.

• 화약ㆍ발파
• /
• 제38권4호
• /
• pp.16-25
• /
• 2020

터널 발파 굴착 시 발생되는 진동을 저감시키기 위해 사용되는 MSP(Multi-setting smart-investigation of the ground and pre-large hole boring method) 공법은 1회 천공 시 수평방향으로 50m에 달하는 장거리를 천공하기 때문에 고 중량 해머비트와 롯드의 일방향 회전으로 롯드의 처짐과 우향 현상이 동반된다. 이는 전문가의 경험과 시공 이력을 바탕으로 가변적인 세팅을 통해 일부 보정되고 있다. 그러나 암반 특성, 장비 상태, 경험 부족 등은 목표 지점으로부터 천공 오차를 발생시키는 원인이 되며, 큰 이격 오차 발생 시 재시공으로 인한 공기 증가와 경제적 손실이 발생된다. 본 연구에서는 딥러닝을 활용하여 상황별 천공 장비의 최적 세팅조건 산정 모델을 개발하였으며, 학습 과정에서 발생 가능한 과적합 문제를 방지하기 위해 dropout, early stopping, pre-training 기법들을 사용하여 향상된 결과를 도출하였다. 본 연구를 통해 대구경 천공 장비의 상황별 초기세팅 산정 모델 개발의 높은 가능성을 확인했으며, 지속적인 데이터 수집과 다양한 인자들의 추가 학습을 통해 최적화된 세팅 가이드라인을 개발할 수 있을 것으로 기대된다.

• 한국자동차공학회논문집
• /
• 제6권1호
• /
• pp.90-98
• /
• 1998

A Dual Mass Flywheel(D.M.F.) system is an evolution to the reduction of torsional vibration and impact noise occurring in powertrain when a vehicle is either moving or idling. The D.M.F. system has two flywh-eels, which is different from the conventional clutch system. One section belongs to the mass moment of in-ertia of the engine-side. The other section increases the mass moment of inertia of the transmission-side. These two masses are connected via a spring/damping system. This reduces the speed at which the dreaded resonance occurs to below idle speed. Since 1984m D.M.F. system has been developed. However, the processes of development of D.M.F. system don't have any difference from the trial and error method of conventional clutch system. This paper present the method for systematical design of D.M.F. system with dimensionless design varia-bles of D.M.F. system, mass ratio between two flywheels, natural frequency rate of two flywheels, and visc-osity coefficient. And expermental results are used to prove these theoretical results.

• Advances in concrete construction
• /
• 제9권2호
• /
• pp.161-171
• /
• 2020

In this paper, an experimental study was conducted on the compressive behavior of steel tube confined concrete (STCC) and concrete-filled steel tube (CFST) columns with active and passive confinement. To create active confinement in the STCC and CFST specimens, an innovative method was used in this study, in which by applying pressure on the fresh concrete, the steel tube was laterally pretensioned and the concrete core was compressed simultaneously. Of the benefits of this technique are improving the composite column behavior, without the use of additives and without the need for vibration, and achieving high prestressing levels. To achieve lower and higher prestressing levels, short and long term pressures were applied to the specimens, respectively. Nineteen STCC and CFST specimens in three groups of passive, short-term active, and long-term active confinement were subjected to axial compression, and their mechanical properties including the compressive strength, modulus of elasticity and axial strain were evaluated. The results showed that the proposed method of prestressing the STCC columns led to a significant increase in the compressive strength (about 60%), initial modulus of elasticity (about 130%) as well as a significant reduction in the axial strain (about 45%). In the CFST columns, the prestressing led to a considerable increase in the compressive strength, a small effect on the initial and secant modulus of elasticity and an increase in the axial strain (about 55%). Moreover, increased prestressing levels negligibly affected the compressive strength of STCCs and CFSTs but slightly increased the elastic modulus of STCCs and significantly decreased that of CFSTs.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권12호
• /
• pp.608-616
• /
• 2006

Recently, a switched reluctance motor is widely used in various industries because it has many advantages such as a simple structure, robustness, less maintenance, high torque/weight ratio, and easy speed control over other types of motors. However, a switched reluctance motor inherently produces acoustic noise and vibration caused by torque ripple. Applications of these motors where silent operation is desirable have thus been limited. In this paper, a new stator pole face having a non-uniform air-gap and a pole shoe attached to the lateral face of the rotor pole are suggested in order to minimize torque ripple. The effects of each design parameter are validated using a time-stepping finite element method. The parameters are optimized by utilizing response surface method (RSM) combined with (1+1) evolution strategy. The result shows that the optimized shape gives higher average torque and drastically reduced torque ripple.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.443-443
• /
• 2009

Cogging Torque is induced by the magnetic attraction between the rotor mounted permanent magnet(PM) and the stator teeth. This torque is an unwanted effect causing shaft vibration, noises, metal fatigues and increased stator length. A variety of techniques exist to reduce the cogging torque of PM generator. Even though the cogging torque can be vanished by skewing the stator slots by one slot pitch or rotor magnets, manufacturing cost becomes high due to the complicated structure and increased material costs. This paper introduces a new cogging torque reduction technique for PM generators that adjusts the azimuthal positions of the magnets along the circumference. A 900 kW class PMSG model is simulated using a three dimensional finite element method and the resulting cogging torques is analyzed using the Maxwell tensor stress tensor. Using the 3D simulation, the end contribution of the cogging torque is accurately calculated.

• EDISON SW 활용 경진대회 논문집
• /
• 제6회(2017년)
• /
• pp.270-281
• /
• 2017

본 논문에서는 헬리콥터 블레이드에서 발생하는 자이로스코픽 세차 진동에 대해 연구하고, 능동 제어기 설계를 통하여 진동 저감 시뮬레이션을 수행한다. 이를 위해, 헬리콥터의 전진 비행시 동역학적 응답을 외팔보 조건을 갖는 회전익의 해석이 가능한 EDISON의 기하학적 정밀 보 구조동역학 프로그램을 이용하여 구조 해석을 진행하고 이를 단순 공기력 모델과 연성하여 공탄성 해석을 수행하였다. 실시간 구조 응답을 구하기 위해 EDISON 프로그램 해석 결과를 비선형 수식으로 모델링하는 기법과 트림해석에는 Newton-Raphson 기법 등이 사용되었다.

• 소음진동
• /
• 제5권2호
• /
• pp.225-234
• /
• 1995

In this study, first, transformation process of damping ratios, whose are evaluated in active control analysis, into damping matrix resulting from installed viscous dampers is illustrated. Then, a method is followed to maximize the effect of response reduction, which leads to optimum locations and size of viscous dampers using sensitivity analysis. Highly coupled nonlinearity between damping ratios and dampers makes it hard to find the optimal size of dampers. Therefore, the nonlinearity is transformed to linear problem with small increments of damping ratios and the size of dampers can be found. However, there are many cases for the size of dampers satisfying the small increment of damping ratios, so it is necessary to select minimum size using optimization technique. To determine optimum locations of dampers, dampers are assumed to be installed between the different stories and their locations are selected corresponding corresponding to the degree of damping size. Numerical examples for the frame structure and the shear wall structure show that optimum locations and size of dampers are different form each other depending on the characteristics of modal responses of the structures. The proposed method in this study can be applied to get optimum locations of active controller in the active control.