• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1401-1409
• /
• 2007

This paper presents a detecting technique for the improvement in quality by appling the various vibrational characteristics theory. The object of this study is to objectively point out faulty gear by developing the program which can be used to analyze and predict the vibrational characteristics caused by gear wear, deformation and nick of auto-transmission. The fault detection methods by vibrational signal analysis of gear have been progressed in the various fields of industry. These methods have the advantage of being easy to attach the accelerometer without discontinuance of the structure. But not all the methods are efficient for finding early faults. So in the thesis, we completed development of the inspection system of vibration by appling the most efficient detecting methods and verified the system's reliability through experiments.

• Journal of Biomedical Engineering Research
• /
• v.14 no.1
• /
• pp.31-40
• /
• 1993

It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propa gation characteristics of the internal vibration in the tissue for the low frequency mechanical vibra lion by using bispectral analysis is proposed. In the method, low frequency vibration of $f_0(=100Hz)$ is applied on the surface of the object, and the waveform of the internal vibration ${\times}{\;}(t)$ is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal ${\times}{\;}(t.)$ at the frequencies ($f_0,{\;}f_0$) and ($f_0,{\;}2f_0$) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, where since bispectrum is free from the gallssian additive noise we can get the value with high S/N. Basic experimental system is con structed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.448-455
• /
• 1996

In this study, to reduce vibration of step motor we use Microstep control. Microstep control of stepmotor is usually thought of as an extension of conventional stepmotor control technology. The essence ofmicro stepping is that we divide the full step of a stepmotor into a number of substep called microstep and cause the stepmotor to move through a substep per input pulse. In ideal case, bycontrolling the individual phase currents of a two-phase step motor sinusoidally we can get uniform torque and step angles. But due to the monlinear characteristics of the step motor, we need to compensate current waveform to improve the overall smoothness of the conventional micro stepping system. We implement digital Pulse Width Modulation(PWM) driver to drive step motor and microphone was used for detecting vibration. Driver enables speed change automatically byincreasing or decreasing micro stepping ratio which we call Automatic Switching on the Fly. To compensate the torque harmonics, Neural Networks is applied to the system and we foundcompensated optimal input current waveform. Finally we can get smooth motion of step motor in a wide range of motor speed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.539-542
• /
• 2005

In this study, we investigated the influence of vibrational stimulation on postural control. To study the effect, the sway of the center of pressure was observed fur two different visual conditions and for three different patterns of vibrational stimulation on plantar area. The two visual conditions were normal condition with visual feedback and blind condition with both eyes closed. The three vibrational stimulations were white noise, constant vibration, and vibration with amplitude modulations (sine curve modulation). The experimental results showed that the sway of the center of pressure distinctively reduced with white noise vibrational stimulation. This result showed that it's possible to use vibrational stimulation for improving the ability of postural control.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.1
• /
• pp.47-56
• /
• 2008

This paper presents a detecting technique for the improvement in quality by appling the various vibrational characteristics theory. The object of this study is to objectively point out faulty gear by developing the program which can be used to analyze and predict the vibrational characteristics caused by gear wear, deformation and nick of auto-transmission. The fault detection methods by vibrational signal analysis of gear have been progressed in the various fields of industry. These methods have the advantage of being easy to attach the accelerometer without discontinuance of the structure. But not all the methods are efficient for finding early faults. So in the thesis, we completed development of the inspection system of vibration by appling the most efficient detecting methods and verified the system's reliability through experiments.

• Annual Conference of KIPS
• /
• 2011.11a
• /
• pp.1174-1176
• /
• 2011

Unfortunately, the number of blind people increases every 5 seconds in our world. An extensive research was made on improving the conventional walking cane and developing a microcontroller based walking stick for the blind with sensors and a feedback in form of vibration. Two different kinds of sensors are used to detect obstacles, ultrasonic and infrared distance sensors. The signal from an ultrasonic sensor is fed to a microcontroller. With the help of the supporting software, the Pulse Width Modulation (PWM) principle is extensively used to form three zones and run the corresponding vibration motor at different spends according to how far the detected object is located. The other infrared distance sensors are connected to amplifiers and after that to their corresponding vibration motors through motor drivers. The vibration motors are to be located around the user's arm to notify the blind of the obstacles in the intended walking way. It can be very reliable and sufficient device guiding the blind other than the conventional walking cane which has many drawbacks which will be explained and discussed.

• The Journal of the Acoustical Society of Korea
• /
• v.42 no.3
• /
• pp.243-249
• /
• 2023

The occurrence of cavitation on the propeller is directly linked to the naval ship's survivability, and it is necessary to design a propeller shape that delays the cavitation inception. However, the propeller cavitation can occur under various operating conditions, thus it is important to identify whether the propeller cavitation exists during operation as well as in the design phase. To this end, it is necessary to use noise or vibration signals on board to monitor the cavitation inception. In this study, a hydrophone and an accelerometer were installed on the ship hull right above the propeller to compare the performance of analyzing cavitation inception between acoustic and vibration signals. Also, a high speed camera was used to visually observe the occurrence of cavitation through an observation window. The measured results showed that the spectral shapes between acoustic and vibration signals were different, but the level increases at each frequency band and the overall level of the frequency band from 1 kHz to 10 kHz showed a similar tendency. The Detection of Envelope Modulation On Noise (DEMON) analysis also showed similar results for both acoustic and vibration signals, confirming that both hydrophones and accelerometers can be utilized in the analysis of cavitation inception.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.5
• /
• pp.2018-2030
• /
• 2015

A two stage ac drive configuration consisting of a single-phase line commutated rectifier and a three-phase voltage source inverter (VSI) is very common in low and medium power applications. The deterministic pulse width modulation (PWM) methods like sinusoidal PWM (SPWM) could not be considered as an ideal choice for modern drives since they result mechanical vibration and acoustic noise, and limit the application scope. This is due to the incapability of the deterministic PWM strategies in sprawling the harmonic power. The random PWM (RPWM) approaches could solve this issue by creating continuous harmonic profile instead of discrete clusters of dominant harmonics. Insufficient filtering at dc link results in the amplitude distortion of the input dc voltage to the VSI and has the most significant impact on the spectral errors (difference between theoretical and practical spectra). It is obvious that the sprawling effect of RPWM undoubtedly influenced by input fluctuation and the discrete harmonic clusters may reappear. The influence of dc link fluctuation on harmonics and their spreading effect in the VSI remains invalidated. A case study is done with four different filter capacitor values in this paper and results are compared with the constant dc input operation. This paper also proposes an ingenious RPWM, a ripple dosed sinusoidal reference-random carrier PWM (RDSRRCPWM), which has the innate capacity of suppressing the effect of input fluctuation in the output than the other modern PWM methods. MATLAB based simulation study reveals the fundamental component, total harmonic distortion (THD) and harmonic spread factor (HSF) for various modulation indices. The non-ideal dc link is managed well with the developed RDSRRCPWM applied to the VSI and tested in a proto type VSI using the field programmable gate array (FPGA).

• Progress in Superconductivity
• /
• v.3 no.1
• /
• pp.78-82
• /
• 2001

The spatial resolution of $high-T_{c}$ scanning SQUID microscope is limited by the washer size of SQUID and the gap distance between SQUID sensor and the sample. In this work, we tried to improve the spatial resolution of scanning SQUID microscope by reducing the size of SQUID sensor fabricated with $YBa_2$$Cu_3$$O_{7}$ thin film. Outer dimensions of the SQUiDs we tested are 24 $\mu\textrm{m}$ $\times$ $ 28\mu\textrm{m}$, $12 \mu\textrm{m}$ $\times$ $16\mu\textrm{m}$, $12\mu\textrm{m}$ x $12\mu\textrm{m}$, $10 \mu\textrm{m}$ $\times$ $10 \mu\textrm{m}$ each. To operate them in the flux-locked loop scheme, we used a direct-coupled electronics instead of using conventional electronics involving a modulation scheme. Since the direct-coupled feedback scheme does not require modulation current adjustment that poses as a practical difficulty in the SQUID operation in modulation-scheme, the direct feedback operation is rather simpler than the conventional modulation method. The resulting noise features were dominated by the noise of preamp in FLL electronics except that of the largest SQUID. The noise levels of SQUIDs are expected below 1$\times$$10^{-5}$ $\Phi_{0}$H $z^{1}$2/ (at 300 Hz), that is a typical noise level for SQUID made of $YBa_2$C $u_3$$O_{7}$ thin film. The data acquisition and motion-controlling parts were also improved, resulting in faster data acquisition rate and less vibration of the system.m.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.8 s.101
• /
• pp.897-903
• /
• 2005

When driving on uniformly tining concrete pavement road, the whine noise which has high spectrum at the specific frequency related to the uniform tining space exist. In this paper, a randomization method of tining space for concrete pavements is proposed to reduce the whine noise. The proposed method is developed based on the LCG(linear congruential generator) algorithm. The design parameters used in the method are number of different tining space, ratio of each tining space, total linings of each size. sequence of actual tining under given constant drag length and texture. Monte Carlo simulations are used to validate the proposed method.