• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.509-514
• /
• 2002

This paper studies on the noise reduction for a small automobile DC Motor (a window motor) using the 6 sigma process. The application of 6 sigma process suggested reliable and valuable statistical data for the quality of the DC motor at the production line. In the measurement step in 6 sigma process, the FMEA(Failure Mode Effect Analysis) were used for the detection of noise sources. The application of 6 sigma process gave not only the improving method for the quality of the DC motor but also the confidence of improvement itself since it was done on the basis of the test results for a number of DC motors at the production line. Consequently the 6 sigma process was proved very effective for the noise reduction at the production line.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 II
• /
• pp.1120-1125
• /
• 2001

A new concept of piezoelectric smart panels for noise reduction in wide band frequencies is proposed and their possibility is experimentally investigated. Multi-mode damping is studied by using a newly proposed tuning method. The proposed panels are based on passive shunt damping methods. This method is based on electrical impedance model and maximizing the dissipated energy at the shunt circuit. four PZT are attached on smart panel for improving performance of transmission noise reduction. 0 prove the concept of piezoelectric smart panels, an acoustic measurement experiment was performed. The smart panels exhibit a good noise reduction in middle and high frequency ranges due to the mass effects of absorbing materials or/and the air gap. The use of piezoelectric smart panel renders noise reduction at resonance frequency. Noise reduction at multiple resonance frequencies is experimentally investigaed.

• Smart Structures and Systems
• /
• 제6권4호
• /
• pp.373-388
• /
• 2010

The updated finite element model of K$\ddot{o}$m$\ddot{u}$rhan Highway Bridge on the Firat River located on the $51^{st}$ km of Elazi$\breve{g}$-Malatya highway is obtained by using analytical and experimental results. The 2D and 3D finite element model of the bridge is created by using SAP2000 structural analyses software, and the dynamic characteristics of the bridge are determined analytically. The experimental measurements are carried out by Operational Modal Analysis Method under traffic induced vibrations and the dynamic characteristics are obtained experimentally. The vibration data are gathered from the both box girder and the deck of the bridge, separately. Due to the expansion joint in the middle of the bridge, special measurement points are selected when experimental test setups constitute. Measurement duration, frequency span and effective mode number are determined by considering similar studies in literature. The Peak Picking method in the frequency domain is used in the modal identification. At the end of the study, analytical and experimental dynamic characteristic are compared with each other and the finite element model of the bridge is updated by changing some uncertain parameters such as material properties and boundary conditions. Maximum differences between the natural frequencies are reduced from 10% to 2%, and a good agreement is found between natural frequencies and mode shapes after model updating.

• 한국소음진동공학회논문집
• /
• 제18권8호
• /
• pp.816-822
• /
• 2008

This study presents the design modification for SCR muffler of a commercial vehicle. Its main objective is the reduction of radiated noise at SCR muffler. For this study, the research of five steps were achieved by experimental and CAE analysis. First step is the measurement of radiated noise using impact-acoustic test. Second step is the source identification using experimental modal analysis. The cause of radiated noise source is confirmed by the resonance of end plates at SCR muffler. Third step confirms the possibility of resonance avoidance using SDM analysis applied the mass control. Fourth step is the suggestion of design modification which is the change of mode shape by CAE analysis. Last step is the verification of design modification using SYSNOISE analysis. Finally, the prototype product applied the countermeasure of resonance evasion was manufactured and the reduction of radiated noise at SCR muffler was confirmed by pass-by noise test.

• 한국안전학회지
• /
• 제13권4호
• /
• pp.41-48
• /
• 1998

In this paper, an investigation was performed on the dynamic interlaminar fracture toughness of CFRP(carbon fiber reinforcement plastics) composite laminates. Composite laminates used in this experimentation are CF/EPOXY and CF/PEEK laminated plates. In the experiments, Split Hopkinson's Bar(SHPE) test was applied to dynamic and notched flexure test. The mode Ⅱ fracture toughness of each unidirectional CFRP was estimated by the analyzed deflection of the specimen and J-integral with the measured impulsive load and reactions at the supported points. As an experimental result, the vibration amplitude of CF/PEEK laminates appear more than that of CF/EPOXY laminates for the J-integral and displacement velocity at a measuring point. Also, it is thought that the dynamic fracture toughness of two kind specimens(CFRP/EPOXY and CF/PEEK) with the in crease of displacement velocity becomes a little greater at a measuring point within the range of measurement.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.675-678
• /
• 2001

In this paper, an investigation was performed on the dynamic interlaminar fracture toughness of CFRP(carbon fiber reinforcement plastics). Specimens used in this experiment are CF/EPOXY laminated plates. In this experiments, Split Hopkinson s Bar test was applied to dynamic and notched flexure test. The mode II fracture toughness of each unidirectional CFRP was estimated by the analyzed deflection of the specimen and J-integral with the measured impulsive load and reactions at the supported points. As an experimental result, the vibration amplitude of 〔$0_{10}F_4/0_{10}$〕laminates appear more than that of 〔0_{10}/F_2/0_{10}$〕laminates for the J-integral and displacement velocity at a measuring point. Also, it is thought that the dynamic fracture toughness of two kind specimen with the increase of displacement velocity becomes great at a measuring point with in range of measurement.

• Smart Structures and Systems
• /
• 제17권3호
• /
• pp.363-389
• /
• 2016

Deficient modes that cannot be always identified from different sets of measurement data may exist in the application of operational modal analysis such as the stochastic subspace identification techniques in large-scale civil structures. Based on a recent work using the long-term ambient vibration measurements from an instrumented cable-stayed bridge under different wind excitation conditions, a benchmark problem is launched by taking the same bridge as a test bed to further intensify the exploration of mode identifiability. For systematically assessing this benchmark problem, a recently developed SSI algorithm based on an alternative stabilization diagram and a hierarchical sifting process is extended and applied in this research to investigate several sets of known and blind monitoring data. The evaluation of delicately selected cases clearly distinguishes the effect of traffic excitation on the identifiability of the targeted deficient mode from the effect of wind excitation. An additional upper limit for the vertical acceleration amplitude at deck, mainly induced by the passing traffic, is subsequently suggested to supplement the previously determined lower limit for the wind speed. Careful inspection on the shape vector of the deficient mode under different excitation conditions leads to the postulation that this mode is actually induced by the motion of the central tower. The analysis incorporating the tower measurements solidly verifies this postulation by yielding the prevailing components at the tower locations in the extended mode shape vector. Moreover, it is also confirmed that this mode can be stably identified under all the circumstances with the addition of tower measurements. An important lesson learned from this discovery is that the problem of mode identifiability usually comes from the lack of proper measurements at the right locations.

• 한국건설순환자원학회논문집
• /
• 제11권4호
• /
• pp.355-363
• /
• 2023

노후 교량의 안전성을 평가하는 방법에 있어서 동특성과 처짐은 구조계의 강성과 직접 연관이 있으며, 처짐의 경우에는 교량 사용자가 직접 감지할 수 있는 물리량으로 가장 중요한 인자이다. 하지만 교량의 처짐을 측정하기 위해서는 교량의 하부에 처짐계를 설치하고 교통 차단 및 재하시험을 실시해야 하는 번거로움이 있어 교량의 환경에 따라서 비용이 증가하거나 측정이 불가능한 문제들이 발생하고 있다. 본 연구에서는 처짐계의 설치 없이 가속도계만을 이용하고 재하시험 없이 상시 진동을 이용하여 교량의 처짐을 측정하는 방법을 제안하였다. 상시 진동을 이용한 교량 동특성 및 처짐 분석을 위해 단순한 연산으로 빠른 분석이 가능하다고 알려진 TDD 기법을 이용하여 교량의 모드형상과 고유진동수를 추출하였으며, 유연도 분석을 통하여 교량의 단위하중 처짐을 분석하여 정적 처짐까지 산정하였다. 본 제안 기술의 검증을 위해 공용중 교량인 C대교(사장교)에 적용하여 모드형상, 고유진동수, 정적 처짐 분석을 수행하였으며 재하시험 실측값과 구조해석 자료와 비교하였다. 그 결과 모드형상 및 고유진동수는 0.42~1.13 %, 중앙경간에서의 최대 처짐은 3.58 %의 오차율을 확인하였다. 따라서 제안기술은 처짐계의 설치가 어려워 실측이 불가능한 교량의 처짐을 추정하여 설계값 및 해석값 대비 처짐 발생량 비교로 교량의 안전성을 간접적으로 파악할 수 있는 근거 자료로 활용 가능할 것으로 사료된다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.68-71
• /
• 2000

A tool holder system has been designed to measure cutting forces in diamond turning. This system includes a 3-component piezo-electric tranducer. In this research, tool holder system is modeled by considering the element dividing, material properties, and boundary conditions using MSC/PATRAN. Mode and frequency analysis of structure is simulated by MSC/NASTRAN, for the purpose of developing the effective design. In addition, tool holder system is verified by vibration test using accelerometer. This system will aid to the development of Fast Tool Servo.

• 한국생산제조학회지
• /
• 제20권5호
• /
• pp.570-575
• /
• 2011

Ultrasonic metal welder is consisted of power supply, transducer, booster, and horn. Precise designing is required since each parts' shape, length and mass can affect driving frequency and vibration mode. This paper analyzed Cu sheet deposition characteristics using ultrasonic metal welder and tension tester. A horn suitable for 40,000Hz was attached to the ultrasonic metal welder in order to weld Cu plates. The Cu sheet welding was done with different amplitude, pressure, and welding time, and its maximum tension was measured with tension tester. Maximum tension of 153.87N was obtained when the pressure was 2.0bar, amplitude was 80%, and welding time was 0.30s. Therefore, excessive welding condition negatively influences maximum tension measurement result.