• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2006.04a
• /
• pp.29-34
• /
• 2006

In general, the vertical vibration problems for .strength of members and serviceability of building structures are not considered in structural design process, but the prediction of the vertical vibration is very important and essential to structural design process. This study aims to investigate the characteristics of vertical vibration in terms of the transfer of horizontal directions on the rahmen building structures. In order to examine the characteristics of vertical vibration, the modal test and the impact (heel-drop and hammer) excitation experiments were conducted several times on three building structures. The results from the experiments are analyzed and compared. with the results. The results of this study suggest that the characteristics of vertical vibration transfer in horizontal way are effected from the fundamental frequency of the slabs and excitation forces.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.71-77
• /
• 2002

The spectrum of impulse response signal which is obtained from an impulse hammer testing is used for frequency response function, nevertheless it has serious faults when the record length for the signal processing is not very long. The faults cannot be avoided with the conventional signal analyzer that is processing all the signals as if they are always periodic. The signals generated by the impact hammer are undoubtedly non-periodic because of the damping, and are acquired for limited recording time due to the memory as well as the computation performance of the signal analyzer. This paper will make clear the relation between the faults and the length of recording time, and propose the way for solving the faults.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.408-413
• /
• 2003

The frequency response function(FRF) of each substructure is used for the transfer function synthesis method(TFS). The dynamic characteristics of the full system are obtained by synthesizing FRFs of each substructure. The validation of TFS depends on accuracy for FRF of each substructure. Impact hammer testing Is widely used to obtain the modal characteristics of structures However. the FRF obtained from impact hammer testing contains bias errors, such as finite record length error and leakage error of which characteristic depends on data acquisition time which we call record length. In this paper, a method to remove hose errors is proposed so as to enhance results of TFS. Numerical and experimental examples show that the FRF of full structure can be predicted nearly exactly by the method proposed in this paper.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.10
• /
• pp.69-77
• /
• 1995

This laser measurement system has been developed using He-Ne laser and photodiode. The laser beam intensity transmitted on a photodiode was disturbed by eccentrically rotating disk cam with various speeds. The photodiode and an amplifier were used to change the detected beam intensity into voltage. The digitized data through the developed system were recorded on a micro-computer by using a signal analysis program. Its reliability was ascertained by using FFT analyzer. The vibration of rotating disk cam can be analyzed by measureing the intensity change of laser beam which the results by FFT analyzer were similar to. The amplifier was devised to be able to modulate the fluctuations of laser beam. The voltage could be linearly recorded with the change of the laser beam intensity.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.942-945
• /
• 2003

Noise cause is dividing to fluid noise by exhaust flow of fan and vibration noise by rotational vibration of motor. Until now, measuring method has been used to measure vibration by the accelerometer, this method has been not measured for the vibration in some parts of brush and commutator because of motor construction. This research was purposed on the accurate analysis. using laser vibration analyzer, of noise cause against the difficult part in old times. By using this measured data, we would like to use for the design of silent motor.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.347.2-347
• /
• 2002

This paper presented a design and a Vibration control of a biped walking RGO(Robotic Gait Orthosis) and walking simulation by this system. The vibration evaluation of the Knee Joint Mechanism on the biped walking RGO(Robotic Galt Orthosis) was used to access by the 3-axis accelerometer with a low frequency vibration for the spinal cord injuries. It will be expect that the spinal cord injury patients are able to recover effectively by a biped walking RGO. (omitted)

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.10
• /
• pp.780-787
• /
• 2014

This paper experimentally deals with the vibration characteristics of flat ring transducers used for ultrasonic sensors and actuators. Radial vibration mode, which is the fundamental mode of a thin piezoelectric transducer, was measured by a laser in-plane vibrometer. An impedance analyzer was used to measure natural frequencies. The results measured by experiments verified theoretical predictions. The vibration characteristics of ring transducers were identified according to the outer diameter size. The shape of the fundamental mode is almost uniform but slightly decreases from the inner to the outer circumferential surfaces. The natural frequency of the fundamental mode decreases as the outer diameter increases. It appears that the ring type transducer is suitable to excite uniformly distributed vibration on a flat surface.

• Journal of the Korean Home Economics Association
• /
• v.34 no.3
• /
• pp.123-136
• /
• 1996

This report deals with the relations between the vibration restraint and the stress-strain properties of the stretch fabrics. For this purpose, a survey was carried out about the preferences in sports-brassiere. Six experimental sports-brassieres of an equal design, but of different materials were tested for vibration using an accelerometer and a motion analyzer while the subject is jogging. 1. The results of the survey on sports-brassiere preferences are as follows; Preferable factors are simple design, shield and close adhesion of sports brassiere. Dissatisfied factors on the sports-brassiere are drooping, vibrating of the breast, itching and wetting. The B-cup-size group perceive the bigger vibration and drooping than A-cup-size. 2. The results of the wearing tests are as follow; This experiment shows the vibration restraint effects on different stretch fabrics, such as hard, medium and soft nature. There was a linear relationship between the vibration restraint and combination of different types of stretch fabrics. Among different brassiere types, the 2-layered brassiere (inner layer of high tension fabric and outer layer of lower stretch fabric) showed the least vibration. In the case of 2-lay brassiere, the wearing comfort rate was highest.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.6
• /
• pp.303-309
• /
• 2012

Energy expenditure values were estimated based on the voice signals and body activities. Voice signals and body activities were obtained using PVDF contact vibration sensor and 3-axis accelerometer, respectively. Vibration caused by voices, activity signals, and actual energy consumption were acquired using data acquisition system and gas analyzer. With the use of power values from the voice signals and weight as independent variables, R-square of 0.918 appeared to show the highest value. For activity outputs, use of signal vector magnitude, body mass index, height, and age as independent variables revealed to provide the highest correlation with actual energy expenditure. Estimation of energy expenditure based on voice and activity provides more accurate results than based on activity only.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.6 no.4
• /
• pp.346-352
• /
• 1982

The vibration characteristics of hyoid gears are experimentally investigated with backlash and tooth mesh frequency varied. Experiments are performed with two types of gear sets; well-machined and over-lapped gears. Through the experimental works, a constant torque 0.8kg.m is applied to th gears and a pulse type of trigger signal synchronizing tooth contact is used to measure the tooth mesh frequency and to average the gear vibration signal in the time domain. The time averaged vibration signals are frequency analyzed by a digital signal analyzer. The experimental results show the vibration characteristics of the two different types of gears in relation to backlash amount and mesh frequency variations are well differentiated by harmonic amplitudes and their ratios, and peak-to-peak amplitude of the gear vibration.