• Journal of KSNVE
• /
• v.26 no.1
• /
• pp.18-23
• /
• 2016

• Journal of KSNVE
• /
• v.26 no.1
• /
• pp.29-34
• /
• 2016

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.3
• /
• pp.308-314
• /
• 2016

This paper proposes design guidances for noise reduction of a bank teller cash recycler(TCR). The operating noise of a TCR is required to be reduced because it bothers bank tellers and customers. The operating noise from a TCR is measured and the most influential driving system is examined. To find the main sources of the noise, the frequency spectra are analyzed by comparing with excitation frequencies of the driving system. From the analysis results, we reveals that the main sources of the noise are gear mesh frequency of a certain gear train and its side band frequencies, which is attributed by vulnerable support condition. Consequently, to reduce the operating noise, the structural modification for the gear train support is suggested and its effectiveness for the noise reduction is confirmed experimentally.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.6_spc
• /
• pp.674-679
• /
• 2016

According to the conventional studies on the noise and cardiovascular effect, railway noise is better associated with hypertension and adverse cardiovascular events than road traffic noise. But the underlying mechanisms remain unclear. We investigated the hypothesis that exposure to acute railway noise would the unfavorable effect of cardiovascular and autonomic system in healthy young subjects. Using a randomized, sham-controlled cross-over design, ten subjects were assigned to receive either an exposure to high speed train noise (84 dB) for 30 minutes or a control condition (non noise), separated by two days. Blood pressure, heart rate, augmentation index and heart rate variability as indices of cardiovascular and autonomic system function were measured at baseline, during, and recovery from two trials. The results show that exposure to acute railway noise significantly increased diastolic blood pressure and augmentation index, which may cause of adverse cardiovascular effects.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.4
• /
• pp.436-442
• /
• 2016

This paper presents the torsional vibration isolation performance evaluation of a centrifugal pendulum absorbers (CPAs) that has a continuously varying resonance frequencies proportional to engine firing (excitation) order. CPAs are commonly used to suppress torsional vibrations in rotating machinery and internal combustion engines. In this study, they are employed on the current spring type torsional damper inside a torque converter of automotive vehicle. To evaluate the effectiveness of designed resonance tuning order, the torsional vibration transmissibility based on torque measurements with respect to different engine firing orders is experimentally measured with a lower-inertia dynamometer. The torsional vibration transmissibility with respect to different frequencies with engine order of 2 is also evaluated. It has been demonstrated that the significant vibration reduction over operational frequency range of interest can be achieved by attaching simple pendulums. Future research direction includes the study on theoretical analysis, improved design of pendulum etc.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.4
• /
• pp.383-390
• /
• 2016

In this paper, experiment and dynamics simulations were carried out to identify and reduce the out-of-plane vibration that occurs in a centrifugal fan of an air conditioner installed to a wall. In a wall-installed air conditioner, large space between a case and heat exchanger is often required for the fan to avoid the collision with the case and exchanger. This large space hinders the slim design of the air conditioner even if air conditioner market demands a slim air conditioner. In the present study, in order to determine the cause of the vibration in the centrifugal fan, the out-of-plane vibration and the physical properties were investigated, and the dynamic characteristics of the centrifugal fan were obtained by experiments. Based on these experiments, a dynamic simulation model was established to determine the cause of the out-of-plane vibration of the centrifugal fan. It was found that the main factor of out-of-plane vibration in the centrifugal fan is the axial misalignment between the centrifugal fan and the motor shaft.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.2
• /
• pp.130-140
• /
• 2016

Floating floor is most commonly used at apartment houses in Korea for thermal insulation and reducing impact noise. But it in proven that the floating floor is not effective for reducing the floor impact noise in low frequency range. In most cases, impact sound pressure level under 63 Hz frequency band were actually increased by the resonance of resilient material, lightweight concrete and the finishing mortar installed on it. In this paper, an integrated floor system consist of 70 mm light weight concrete and 40 mm finishing mortar successively installed on the concrete slab was suggested to avoid the resonance. Integrated floor system increases total flexural stiffness and mass per unit area. The natural frequencies of first and second vibration mode were increased and acceleration response and floor impact sound level was decreased in all measurement range.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.7
• /
• pp.827-835
• /
• 2016

Ride comfort of a vehicle is often determined by rubber bushes in suspension system. If transmission forces versus deformations across the bushes are available under operational conditions, improvement of the ride comfort could be done with more ease. Recently, the transmission forces are measured using custom-made force transducers inside the links. This study presents a feasibility study on estimation of the rubber bush deformations using vibration signals on the rigid links. Linear variable displacement transducers as well as piezoelectric accelerometers are used to expand frequency range to very low frequency, which cannot be done with accelerometers only. How to estimate the bush deformation from the two vibration signals on the links are presented together with experimental results.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.7
• /
• pp.851-856
• /
• 2016

In this paper, the free vibration characteristics of longitudinally corrugated cylindrical shells is investigated by the theoretical analysis. The equivalent homogenization model is adapted to investigate the overall mechanical behavior of these corrugated shells. The corrugated element can be represented as an orthotropic material. Both the effective extensional and flexural stiffness of this equivalent orthotropic material are considered in the analysis. To demonstrate the validity of the proposed theoretical approach, the theoretical results are compared with those from 3D finite element analysis using ANSYS commercial code. Some numerical results are presented to check the effect of the geometric properties.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.7
• /
• pp.781-786
• /
• 2016

All measurements are subject to uncertainty and a measurement result is complete only when it is accompanied by a statement of the associated uncertainty. By international agreement, this uncertainty has a probabilistic basis and reflects incomplete knowledge of the quantity value. The "Guide to the Expression of Uncertainty in Measurement", commonly known as the GUM, is the definitive document on this subject. The requirements for estimation of measurement uncertainty apply to all results provided by calibration laboratories and results produced by testing laboratories under the optional circumstances. In this paper, a procedure for estimation of measurement uncertainty from vibration testing is proposed on KS F 2868:2003 as an example. Both Type A and Type B evaluation of uncertainty are considered to calculate the combined standard uncertainty and expanded uncertainty.