• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.1
• /
• pp.23-29
• /
• 2011

The measurement of ice properties such as thickness, strength are important to know the performance of the ice breaking vessel. The measuring equipment of ice properties and methods are summarized in this paper. The actual measured data are also described. The strength of ice at Svalbard area on April 2010 is much stronger than the Chukchi Sea on August 2010. The mean strength of Svalbard is about 500 kPa and one of Chukchi Sea is 250 kPa. The first sea trial in Arctic sea using Araon was carried out in the Chukchi Sea. The power and speed was also measured to check the ship performance in ice. The speed was measured from GPS(Global Positioning System) and engine power was recorded from DPS(Dynamic Positioning system) of Araon. The design target of Araon in level ice is 3 knots in 1m thickness and 630 kPa flexible strength but mean speed in Chuckchi sea is 3.98 knots when 6.6 MW engine power, 2.4m ice thickness and 250 kPa strength. This results comes from the difference of ice types and the weak flexible strength of ice but it will be a good information to know the performance of Araon in similar ice condition.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.58 no.3
• /
• pp.214-222
• /
• 2022

This study calculated the on-site measurement (Tier 4) of greenhouse gases emitted during the production stage of major fishing periods that utilize set nets and bamboo weir fishing boats. In addition, using theoretically calculated results (Tier 1), the emission factor presented by the Intergovernmental Panel on Climate Change (IPCC) was comparatively analyzed. On average, carbon emissions for each operating period in the bamboo weir and set net were calculated to be 0.16 and 3.58 kg CO₂ time^-1, respectively; and the measurement values (Tier 4) for each tool were about 4-17 times lower than their respective theoretical values (Tier 1). Significant differences were found based on engine performance. As port entry, port departure, and operating periods of the vessels show negligible variation with short distances, the operation of the vessel engine was considered as the main variable for carbon emissions in anchovy set net fishing.

• Journal of Energy Engineering
• /
• v.20 no.3
• /
• pp.178-184
• /
• 2011

Compressed Air Energy Storage (CAES) is a combination of energy storage and generation by storing compressed air using off-peak power for generation at times of peak demand. In general, both charging and discharging of high-pressure vessel are unsteady processes, where the pressure is varying. These varying conditions result in low efficiencies of compression and expansion. In this paper, a new constant-pressure CAES system to overcome the current problem is proposed. An energy analysis of the system based on the concept of exergy was performed to evaluate the energy density and efficiency of the system in comparison with the conventional CAES system. The new constant-pressure CAES system combined with pumped hydro storage requires the smaller cavern with only half of the storage volume for variable-pressure CAES and has a higher efficiency of system.

• Proceedings of KOSOMES biannual meeting
• /
• 2017.04a
• /
• pp.244-244
• /
• 2017

Recently, A study is actively underway to apply to various industries, which are one of the major changes in the key drivers of the industry 4.0.. The data generated by the ship include various indicators such as the fuel volume, engine power, ground speed, speed, speed, main engine rpm, DFOC, SFOC, and FOC. This paper analyzes the sensitivity of the Gathering data and analyzes the impact energy efficiency of the vessel operation by analyzing the influence among each parameter, using the mathematical models, you create an surrogate model using the math model, comparative analysis of actual measurement data and predictive results were analyzed. Through the use of big data analysis technology, it is possible to identify the sensitivity between the energy efficiency related variables of the ship, The possibility of utilization of fuel efficiency indicators using of the surrogate model is identified.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.14 no.2
• /
• pp.97-112
• /
• 1978

The rule 15, 16 and 17 of International Regulations for Preventing collisions at Sea direct actions to avoid collision when two power-driven vessels are crossing. But these rules do not present the safety minimum approaching distances outside which a give- way vessel deeps out of the way of a stand-on vessel. In this paper, the author analyzed the ship's collision avoiding actions from a viewpoint of ship kinematics as the method to calculate this distance. The author worked out mathematic formulas for calculating the safety minimum approaching distances outside which the give-way vessel takes the actions to avoid collisions in accordance with the cross angles of the crossing vessels' courses. Figuring out actually the values of maneuvering indices of the M. S. Koan Ack San (GT: 224tons), the training ship of the National Fisheries University of Busan and the M. S. Golden Clover (GT: 101, 235tons) of the Eastern Shipping Co., Ltd. through their Z test, the author applied these values to the calculating formulas and calculated the safety minimum approaching distances. The results of calculations are as follows; 1. The greatest distance is to be kept by the give-way vessel to avoid collision when the cross angle of courses is 90$^{\circ}$ or near it. In such case the safety minimum approaching distance of a small vessel must be more than 5 times of her own length and that of a large vessel more than 11 times of her own length. 2. Collision danger is greater when crossing angle is obtuse than in an acute angle, therefore greater distance is to be kept by the give-way vessel to avoid collision in the case of the obtuse angle. 3. The actions to be taken to avoid collisions by the give-way vessel in Rule 16 and by the stand-on vessel in Rule 17(a)(ii) of International Regulations for Preventing Collisions at Sea, must be done outside the above safety minimum approaching distance. When inevitably such actions are to be taken within the safety minimum approaching distance, they should be accompanied with engine motions.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.6
• /
• pp.681-687
• /
• 2014

The objective of this work presented here was focused on analysis of in-cylinder combustion characteristic, engine performance, and nitrogen oxides emission characteristic from marine gas oil for propulsion diesel engine of naval vessels and biodiesel with fuel injection timing in a single cylinder diesel engine. In addition, combustion process was analyzed with a high speed camera of marine gas oil and biodiesel fuel. Retarding the fuel injection timing from $BTDC25^{\circ}CA$ to $BTDC5^{\circ}CA$, in cylinder peak combustion pressure was gradually decreased, however, engine torque showed a tendency to increase. The highest nitrogen oxides level was measured at $BTDC15^{\circ}CA$, they were reduced at retarded and advanced condition on the basis of $BTDC15^{\circ}CA$. Comparing with combustion process of marine gas oil and biodiesel fuel at $BTDC5^{\circ}CA$, self-ignition timing of biodiesel fuel included oxygen content was faster than marine gas oil, however, a cautious observation indicates a slightly higher flame intensity for marin gas oil than biodiesel as a diffusion flame is developing.

• International Journal of Automotive Technology
• /
• v.8 no.3
• /
• pp.275-281
• /
• 2007

GTL (Gas To Liquid) has the potential to be used in diesel engines as a clean alternative fuel due to advantages in emission reduction, particularly soot reduction. Since the physical properties of GTL fuel differ from those of diesel fuel to some extent, studying how this difference in characteristics of GTL and diesel fuels affects spray and combustion in diesel engines is important. In this study, visual investigation of sprays and flames from GTL and diesel fuels in a vessel simulating diesel combustion was implemented. The effects of various parameters and conditions, such as injection pressure, chamber temperature and pilot injection on liquid-phase fuel length and auto-ignition delay were investigated. It was determined that GTL has a somewhat shorter liquid-phase fuel length, which explains why there is less contact between the fuel liquid-phase and flame for GTL fuel compared to diesel fuel.

• Journal of Korea Ship Safrty Technology Authority
• /
• s.27
• /
• pp.53-62
• /
• 2009

오늘날의 선박은 디지털 선박(Digital-ship)으로 변화하고 있으며, 일부 유비쿼터스(Ubiquitos) 기술을 기반으로 e-Navigation 및 VTS(Vessel Traffic Service) 등 안전 항해 및 편의를 제공하고 있다. 하지만, 아직까지 선박에 대한 안전시스템이 미비하고, 선박의 주요 설비를 실시간으로 관리하기 위한 안전 관리 시스템의 개발이 매우 필요한 시기라 할 수 있다. 지금까지 선박 연구에 있어서 안전을 극대화시키기 위한 노력은 많았으나 선박의 재질(철판) 및 밀폐환경에 의해 무선 통신(Wireless Communication)을 이용한 시스템 개발은 많이 이루어지고 있지 않은 상태이다. 본 논문은 선박 내의 전파 특성을 분석하여 무선 통신을 하기 위한 최적의 조건을 찾고, 유비쿼터스 기술을 적용한 지그비 네트워크 구성으로 선박 내 엔진관리를 위한 무선 센서 네트워크(Wireless Sensor Network)의 적용 가능성을 검증하였다.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2012.06a
• /
• pp.152-153
• /
• 2012

While engine room arranging pipe which is used from the vessel, It measured the internal flow of 90 degree elbow which is used from the main condenser. Fluid flow in elbow of 90 degree is measured by PIV and Dewetron system. The Reynolds number adopts 50000 and experimental study of flow field in the elbow.

• Journal of Power System Engineering
• /
• v.9 no.4
• /
• pp.214-219
• /
• 2005

The effects of change in injection pressure on spray structure in high temperature and pressure field have been investigated. The analysis of liquid and vapor phases of injected fuel is important for emissions control of diesel engines. Therefore, this work examines the evaporating spray structure using a constant volume vessel. The injection pressure is selected as the experimental parameter, is changed from 72MPa to 112MPa by using a common rail injection system(ECD-U2). The images of liquid and vapor phase in the evaporating free diesel spray are simultaneously taken by exciplex fluorescence method. As a result, it can be confirmed that the distribution of vapor concentration is more uniform in the case of the high injection than in that of the low injection pressure.