• Journal of Ship and Ocean Technology
• /
• v.3 no.4
• /
• pp.35-51
• /
• 1999

Fatigue strength assessment procedures have been implemented in the ship design rules by many classification societies. However, a large variation tin the details of the different approaches exists in practically all aspects influding load history assessment, stress evaluation and fatigue strength assessment. In order to assess the influences of thesd variations on the prediction of fatigue lives. a comparative study is organized by the ISSC Committee III.2 Fatigue and Fracture. A pad detail on the top of longitudinal hatch coaming of a panamax container vessel is selected for fatigue calculation. The work described in this paper is one set of results of this comparative study in which the ABS dynamics approach is applied. Through this analysis the following conclusions can be drawn. (1) With the original ABS approach, the fatigue life of this pad detail is very low, only 2.398 years. (2) The treatment of the stillwater bending moment in the ABS approach might be a source of conservatism. If the influence of stillwater bending moment is ignored, then the fatigue life for this pad detail is 7.036 years. (3) The difference between the nominal stress approach and the hot spot stress approach for this pad detail is about 26%.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2005.06a
• /
• pp.15-21
• /
• 2005

In this paper, the procedure of generation and application of nonlinear wave loads for structural design of large container carrier was described. Ship motion and wave load was calculated by modified strip method. Pressure acting on wetted hull surface was calculated taking into account of relative hull motion to the wave. Design wave height was determined based on the most sensitive wave length considering rule vertical wave bending moment at head sea or fellowing sea condition. And the enforced heeling angie concept which was introduced by Germanischer Lloyd (GL) classification had been used to simulate high torsional moment in way of fore hold parts similar to actual sea going condition. Using wave load generated from this dynamic load calculation, FE analyses were performed. With this result, yielding, buckling, hatch diagonal deflection and fatigue strength of hatch corners were reviewed based on the requirement of GL classification. The results of FE analysis show good compatibility with GL classification.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2005.06a
• /
• pp.22-30
• /
• 2005

Sloshing loads, produced by the violent liquid free-surface motions inside the cargo tank have become an important design parameter in ship building industry since there have been demands for the increased sizes of the cargo containment system of LNG carriers. In this study, sloshing impact pressure acting on the shell of the spherical cargo tank of an LNG carrier as well as dynamic pressure and flow behavior around the pump tower located at the center of the tank have been calculated. Comparative numerical sloshing simulations for a spherical LNG tank using 2-D LR.FLUIDS which is based on the finite difference method and 3-D MSC.DYTRAN which is capable of calculating nonlinear fluid-structure interaction have been carried out. A method of calculating sloshing-induced dynamic loads and the subsequent structural strength analysis for pump tower of a spherical LNG carrier using MSC. DYTRAN and MSC.NASTRAN have been presented.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2005.06a
• /
• pp.31-37
• /
• 2005

An attempt to improve the speed performance through the minimizing in wave resistance has been done by an application of gooseneck and no bulb type to bulbous bow for the DSME 78,500 Class LPG Carrier on the basis of the CFD calculation and comparatives model tests. The hydrodynamic characteristics according to the variation of the shape of Cp-curve, design load water line, frame line and bulbous bow that have an important effect on the wave resistance has been evaluated/calculated by ship-flow code. A wide variety in hull variation have been tried to have a good hull form with three types of fore-body hull forms mainly classified by the shape of bulbous bow. The speed performances for the three final hull forms with different bulbous bows have been evaluated through the model tests.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2004.11a
• /
• pp.297-302
• /
• 2004

This paper analyzed productivity of quay cranes on container terminal that have perpendicular yard layout block. In most existing container terminals, quay cranes of single trolley type are used to loading and unloading containers, but quay crane productivity of these type has many limitation about large size containership. For these reasons, recently quay cranes of various type that mn improve productivity are developed and as the representative example, dual trolley, double trolley, supertainer are developing. These cranes are realized that very high productivity bemuse their cycle time is short more than existent single trolley quay crane. Therefore, we analyzed productivity of these cranes that are realized by next generation crane alternatives and as result qf this research, mechaniml productivity by cycle time and net productivity by simulation were measured.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.4
• /
• pp.1130-1147
• /
• 2014

Large size ships have a very flexible construction resulting in low resonance frequencies of the structural eigen-modes. This feature increases the dynamic response of the structure on short period waves (springing) and on impulsive wave loads (whipping). This dynamic response in its turn increases both the fatigue damage and the ultimate load on the structure; these aspects illustrate the importance of including the dynamic response into the design loads for these ship types. Experiments have been carried out using a segmented scaled model of a container ship in a Seakeeping Basin. This paper describes the development of the model for these experiments; the choice was made to divide the hull into six rigid segments connected with a flexible beam. In order to model the typical feature of the open structure of the containership that the shear center is well below the keel line of the vessel, the beam was built into the model as low as possible. The model was instrumented with accelerometers and rotation rate gyroscopes on each segment, relative wave height meters and pressure gauges in the bow area. The beam was instrumented with strain gauges to measure the internal loads at the position of each of the cuts. Experiments have been carried out in regular waves at different amplitudes for the same wave period and in long crested irregular waves for a matrix of wave heights and periods. The results of the experiments are compared to results of calculations with a linear model based on potential flow theory that includes the effects of the flexural modes. Some of the tests were repeated with additional links between the segments to increase the model rigidity by several orders of magnitude, in order to compare the loads between a rigid and a flexible model.

• Journal of Navigation and Port Research
• /
• v.34 no.10
• /
• pp.781-786
• /
• 2010

In this study, a new concept of ocean transport system, called the mobile harbor serving for a short distance transport of containers with cargo handling cranes between mother containerships and coastal ports, is introduced. Instead of direct berthing a very large containership at the coastal port, Mobile Harbor is moving to the offshore mooring basin with enough water depth condition. Therefore, investigation of the coastal environment, technical condition and limitation of the domestic trade ports for the application of Mobile Harbor, is essential process. To figure out the accessibility of mobile harbor, the environmental conditions, the cargo handling capacity and marine traffic volume and flow pattern has been analyzed with the tools for marine traffic simulation and virtual navigation aids system. The most proper Mobile Harbor mooring areas among trade ports of the south and east coast are selected by analyzing the obtained information and evaluating its application: (1) Under natural environmental conditions such as air and sea weather, three candidate areas are selected such as Masan port, Ulsan port, and Busan(New port) port. (2) Under marine traffic and appropriateness of water facilities, three candidate areas are selected as Mokpo port, Busan(New port) port, and Donghae & Mookho port (3) For a region-based analysis considering handling capacity and the local managed trade ports in vicinity, three candidate areas are selected as Busan region, Yosu & KwangYang region, and Mokpo region. Through this study, the basic guideline for selection of optimum trade port and offshore mooring basin for mothership and Mobile Harbor is recommended. In order to apply the Mobile Harbor to the real water, navigaton aids as the virtual route identification with AIS must be introduced for maritime safety in the vicinity of Mobile Harbor area which berthing and cargo handling is being conducted.