• International conference on construction engineering and project management
• /
• 2005.10a
• /
• pp.655-661
• /
• 2005

For a hydro power plant project, the headrace tunnel having a finished diameter of 3.3m was constructed in volcanic rocks with well-developed vertical joint and high groundwater table. The intake facility was located 20.3 km upstream of the powerhouse and headrace tunnel of 20 km in length and penstock of 440 m in height connected the intake and the powerhouse. The typical caldera lake, Lake Toba set the geology at the site; the caving of the ground caused tension cracks in the vertical direction to be developed and initial stresses at the ground to be released. High groundwater table(the maximum head of 20 bar) in the area of well-connected vertical joints delayed the progress of tunnel excavation severely due to the excessive inflow of groundwater. The excavation of tunnel was made using open-shield type TBM and mucking cars on the rail. High volume of water inflow raised the water level inside tunnel to 70 cm, 17% of tunnel diameter (3.9 m) and hindered the mucking of spoil under water. To improve the productivity, several adjustments such as modification of TBM and mucking cars and increase in the number of submersible pumps were made for the excavation of severe water inflow zone. Since the ground condition encountered during excavation turned out to be much worse, it was decided to adopt PC segment lining instead of RC lining. Besides, depending on the conditions of the water inflow, rock mass condition and internal water pressure, one of the invert PC segment lining with in-situ RC lining, RC lining and steel lining was applied to meet the site specific condition. With the adoption of PC segment lining, modification of TBM and other improvement, the excavation of the tunnel under severe groundwater condition was successfully completed.

• Journal of Biosystems Engineering
• /
• v.8 no.2
• /
• pp.11-17
• /
• 1983

Stress distribution under a driving lugged wheel was obtained by photoelastic method. The distribution showed two distinct parts, one part is due to sinkage and other due to compression. Results of the study are summarized as follows. 1. The tangential reactions of sinkage as well as compressing parts were directly proportional to tangential load to the driving wheel, that's appeared to be thrust of the driving wheel. The normal reactions of both sinkage and compressing parts were directly proportional to the vertical load to the driving wheel, that's appeared to be resistance against wheel motion. 2. When the tangential load was constant, changing the vertical load did not show any significant thrust variation of the driving wheel. 3. Under the condition of this experiment, the ratio of vertical load to tangential load (T.L/V.L) must be greater than 1.0 in order for the wheel to roll.

• The Korean Journal of Ecology
• /
• v.17 no.2
• /
• pp.113-119
• /
• 1994

Vertical and horizontal distribution and seasonal changes of fine roots as well as inorganic nitrogen content in soil were determined in Quercus mongolica and Quercus acutissima stands in Mt. Taemosan, Seoul. The vertical distribution of fine rooth phytomass showed a power-functional decrease as descending soil depth. Fine root phytomass was 170 g $DM/m^2$(46%) and 225 g $DM/m^2$(47%) in top soil of 5 cm depth, and 370 g $DM/m^2$ and 480 g $DM/m^2$ from soil surface to 50 cm depth in Q. mongolica and Q. acutissima stands, respectively. Fine roots in relation to the distance from the nearest tree were evenly distributed horizontally in both stands. Fine roots phytomass in top soil of 5 cm depth reached a peak in June, and thereafter decreased gradually in both stands. Patterns of seasonal changes in fine root phytomass were closely related to inorganic nitrogen and moisture content.

• Atmosphere
• /
• v.19 no.3
• /
• pp.289-296
• /
• 2009

Measurements of the three-dimensional water vapor distribution in the atmosphere are important for forecast and analysis of meteorological phenomenon. In this study, two Global Positioning System (GPS) campaign networks were installed in Jeju Island and Kangwon-do to construct the vertical water vapor profile solely based on GPS measurements. We implemented a layer model to get the wet refractivity profile and compared the result with radiosonde measurements. The result showed that the vertical profiles from GPS and radiosonde agree well. The bias, root-mean-square error (RMSE) and standard deviation of GPS wet refractivities compared with radiosonde measurements were in the range of 6.6~11.1 mm $km^{-1}$, 11.9~13.9 mm $km^{-1}$, and 4.3~12.3 mm $km^{-1}$, respectively.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.7
• /
• pp.833-841
• /
• 2007

The aim of this paper is to analyze the conjugate problems of heat conduction in solid walls coupled with laminar free convection flow adjacent to a vertical flat plate under boundary layer approximation. Using the similarity transformations the governing boundary layer equations for momentum and energy are reduced to a system of partial differential equations and then solved numerically using Finite Difference Method(FDM) known as the Keller-box scheme. Computed solutions to the governing equations are obtained for a wide range of non-dimensional parameters that are present in this problem, namely the coupling parameter P. the Prandtl number Pr and the heat generation parameter Q. The variations of the local heat transfer rate as well as the interface temperature and the friction along the plate and typical velocity and temperature profiles in the boundary layer are shown graphically. Numerical solutions have been consider for the Prandtl number Pr=0.70

• Earthquakes and Structures
• /
• v.11 no.3
• /
• pp.407-420
• /
• 2016

The aim of this study is to investigate the effect of vertical ground motion (VGM) on seismic behavior of reinforced concrete (RC) regular frame with construction joints, and determine more proper modeling method for cast-in-situ RC frame. The four-story RC frames in the regions of 7, 8 and 9 earthquake intensity were analyzed with nonlinear dynamic time-history method. Two different methods of ground motion input, horizontal ground motion (HGM) input only, VGM and HGM input simultaneously were performed. Seismic responses in terms of the maximum vertex displacement, the maximum inter-story drift distribution and the plastic hinge distribution were analyzed. The results show that VGM might increase or decrease the horizontal maximum vertex displacement depending on the value of axial load ratio of column. And it will increase the maximum inter-story drift and change its distribution. Finally, proper modeling method is proposed according to the distribution of plastic hinges, which is in well agreement with the actual earthquake damage.

• Journal of Korean Society for Atmospheric Environment
• /
• v.15 no.5
• /
• pp.639-647
• /
• 1999

Experimental methods of plume dispersion in convective boundary layer using a composite turbulence water tank have been established through (ⅰ) manufacturing of water tank system, (ⅱ) providing of tracer whose volatility is relatively low, (ⅲ) development of software for image processing of dispersed particles in fluid, and (ⅳ) application of appropriate similarity law. Using these methods, the vertical dispersion coefficient $$\sigma$_2$ at long distances on mesoscale and the centerline height $Z_c$ of plumes have been measured. Measurement of $$\sigma$_2$ have been validated through comparison with CONDORS field experiments, and analysed with respect to the intensity of heat flux and mechanical turbulence as well as plume release height. Downwind distance where plume center height approaches to final level has also been analysed in respect of these three parameters.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1999.04a
• /
• pp.151-158
• /
• 1999

The single layer latticed domes have various behaviors with each geometrical shape and scale, and they are affected by vertical component as well as horizontal component of the dynamic load. And they represent very different earthquake responses under each ground acceleration compared with another structural systems. Generally, all of the members of latticed domes undergo three dimensional deflections if they are subjected to arbitrary one dimensional horizontal load under earthquake motions. And their response characteristics are very different to their shapes, rise/span ratios, and damping mechanisms. In this study the .earthquake response behavior is verified according to the factor of each shape, rise/span ratio, ana damping ratio of latticed domes, which undergo horizontal and vertical earthquake motions by numerical approaches.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1996.10a
• /
• pp.202-209
• /
• 1996

In this paper, two dimensional vertical and comer infinite elements which can include multiple wave components to model underlying half space are developed. These elements are natural and economical to model underlying stiff half space or rock. To verify the behavior of these infinite elements, vertical, horizontal, and rocking compliances of a rigid strip foundation on a viscoelastic soil profile are analyzed and compared with those of Tzong and Penzien who used the boundary solution method. Good agreements are noticed between the two methods. The influence of material properties like Poisson's ratio, material damping, and stiffness ratio of layers as well as the influence of geometrical properties such as layer thicknesses and depth of foundation embedment are studied. Example analysis is carried out for the shaking table which is located in KIMM(Korea Institute of Machinery and Materials), and the vertical and horizontal displacements of the analysis are compared with the measured, and show good results and demonstrate the efficiency of the proposed method.

• The Journal of the Korean dental association
• /
• v.53 no.11
• /
• pp.844-854
• /
• 2015

This clinical report describes an orthodontic-prosthodontic interdisciplinary treatment for a patient with multiple missing teeth and unilateral scissors bite. A 47-year-old female presented with multiple missing posterior teeth, anterior large overjet, deep bite, and posterior scissors bite on the right premolar area. Periodontal therapy was performed and followed by orthodontic treatment. The maxillary anterior teeth were initially aligned, then two implants were placed for the left mandibular molars to increase occlusal vertical dimension. The scissors bite between the right maxillary and mandibular premolars were corrected using the miniscrews as an anchorage. Other implants were placed for the right maxillary and mandibular molars after the occlusal planes and occlusal relationship were harmonized. The patient adapted well to altered vertical dimension without any specific problems including peri-implant marginal bone loss. Interdisciplinary approach resolve the complex orthodontic-prosthodontic problems and concluded in successful results.