• Steel and Composite Structures
• /
• v.39 no.1
• /
• pp.109-123
• /
• 2021

This research endeavor intends to use the implicit finite element method to investigate the structural response of steel shear walls with partial plate-column connection. To this end, comprehensive verification studies are initially performed by comparing the numerical predictions with several reported experimental results in order to demonstrate the reliability and accuracy of the implicit analysis method. Comparison is made between the hysteresis curves, failure modes, and base shear capacities predicted numerically using ABAQUS software and obtained/observed experimentally. Following the validation of the finite element analysis approach, the effects of partial plate-column connection on the strength and stiffness performances of steel shear wall systems with different web-plate slenderness and aspect ratios under monotonic loading are investigated through a parametric study. While removal of the connection between the web-plate and columns can be beneficial by decreasing the overall system demand on the vertical boundary members, based on the results and findings of this study such detachment can lower the stiffness and strength capacities of steel shear walls by about 25%, on average.

• Computers and Concrete
• /
• v.27 no.2
• /
• pp.153-162
• /
• 2021

This paper aims to simulate the isotropic elastic damage theory of Liu Jun (2012) using the self-programmed UMAT subroutine in the interface of ABAQUS. Liu Jun (2012)'s method based on the mechanic theory can not be used interactively with the currently commonly used finite element software ABAQUS. The advantage of this method in the paper is that it can interact with ABAQUS and provide a constitutive program framework that can be modified according to user need. The model retains the two scalar damage variables and the corresponding two energy dissipation mechanisms and damage criteria for considering the tensile and compressive asymmetry of concrete. Taking C45 concrete as an example, the relevant damage evolution parameters of its tensile and compressive constitutive model are given. The study demonstrates that the uniaxial tensile stress calculated by the subroutine is almost the same as the Chinese Concrete Design Specification (GB50010) before the peak stress, but ends soon after the peak stress. The stress-strain curve of uniaxial compression calculated by the subroutine is in good agreement with the peak stress in Chinese Concrete Design Specification (GB50010), but there is a certain deviation in the descending stage. In addition, this paper uses the newly compiled subroutine to simulate the shear bearing capacity of the shear key in a new structural system, namely the open-web sandwich slab. The results show that the damage constitutive subroutine has certain reliability.

• Journal of The Korean Association of Information Education
• /
• v.25 no.2
• /
• pp.377-385
• /
• 2021

This study attempted to develop and apply a physical computing SW education program applying design thinking. The produced SW education program was applied to 22 students in the 5th and 6th grades of J and B elementary schools located in Jeju-si. Computational thinking ability and creativity pre-test was conducted, and Physical computing software training applied design thinking was conducted over a total of 5 sessions for 20 hours, followed by a post-test on creativity and computational thinking ability. As a result of the verification, it was found that physical computing SW education program applying design thinking was effective in improving the creativity and computing thinking ability of elementary school students.

• Nuclear Engineering and Technology
• /
• v.53 no.4
• /
• pp.1167-1175
• /
• 2021

The process of automation and monitoring in industrial control system involves the use of many types of sensors. A programmable logic controller plays an important role in the automation of the different processes in the power plant system. The major control units are boiler for temperature and pressure, turbine for speed of motor, generator for voltage, conveyer belt for fuel. The power plant units are controlled using microcontrollers and PLCs, but FPGA can be the feasible solution. The paper focused on the design and simulation of hardware chip to monitor boiler, turbine, generator and conveyer belt. The hardware chip of the plant is designed in Xilinx Vivado Simulator 17.4 software using VHDL programming. The methodology includes VHDL code design, simulation, verification and testing on Virtex-5 FPGA hardware. The system has four independent buzzers used to indicate the status of the boiler, generator, turbine motor and conveyer belt in on/off conditions respectively. The GSM is used to display corresponding message on the mobile to know the status of the device in on/off condition. The system is very much helpful for the industries working on plant automation with FPGA hardware integration.

• Journal of Aerospace System Engineering
• /
• v.16 no.6
• /
• pp.74-80
• /
• 2022

The utilisation of small drones is becoming increasingly widespread particularly in the military sector. In this study, STANAG 4586, a standard interface for military unmanned aerial vehicles, was applied to a multicopter-type small drone to examine the suitability of the military system. To accomplish this, a small multi-copter vehicle was designed and manufactured, integrating a flight control computer, ground control system, and data link. Furthermore, flight control and ground control equipment software were developed by applying the STANAG 4586 interface, followed by HILS and flight tests.

• Journal of ILASS-Korea
• /
• v.27 no.3
• /
• pp.155-160
• /
• 2022

Recently, major developed countries have strengthened automobile fuel efficiency regulations and carbon dioxide emission allowance standards to curb climate change caused by global warming worldwide. Accordingly, research and manufacturing on electric vehicles that do not emit pollutants during actual driving on the road are being conducted. Several automobile companies are producing and testing electric vehicles to commercialize them, but it takes a lot of manpower and time to test and evaluate mass-produced electric vehicles with driving mileage of more than 300km on a per-charge. Therefore, in order to reduce this, a simulation model was developed in this study. This study used vehicle information and MCT speed profile of small electric vehicle as basic data. It was developed by applying Simulink, which models the system in a block diagram method using MATLAB software. Based on the vehicle dynamics, the simulation model consisted of major components of electric vehicles such as motor, battery, wheel/tire, brake, and acceleration. Through the development model, the amount of change in battery SOC and the mileage during driving were calculated. For verification, battery SOC data and vehicle speed data were compared and analyzed using CAN communication during the chassis dynamometer test. In addition, the reliability of the simulation model was confirmed through an analysis of the correlation between the result data and the data acquired through CAN communication.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.4_2
• /
• pp.639-648
• /
• 2023

In modern society, UAM (Urban Air Mobility) transportation system is being developed as an alternative to urban traffic congestion and environmental problems, and electric vertical take-off and landing (eVTOL) is a combination of vertical take-off and landing function and electric power. It is attracting attention as an innovative next-generation transportation method as an eco-friendly alternative that reduces noise and air pollution by providing efficient mobility within the city. Since eVTOL development requires designing and implementing airframes suitable for various mission purposes, the power system needs to be developed as a platform concept before airframe development. In this study, we empirically proposed a test bench concept equipped with a stable power supply and an efficient control system, essential in developing a power platform with a combined function in the form of a fuselage and module type specialized for various mission purposes. The proposed drivetrain platform test bench consists of a system verifying the stable take-off and landing software and a power platform adjusting the motor's thrust. It will serve as a verification system that can be developed.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.267-267
• /
• 2023

최근 이상기상현상과 기후변화로 인하여 국지적인 집중호우의 빈도 및 규모가 증가하고 있으며, 이로 인한 돌발 홍수 피해가 증가하고 있다. 레이더는 넓은 영역에 대해 고해상도의 강우 정보를 제공할 수 있으므로 위험기상 감시 및 실황 예측 모형의 입력자료로써 활용도가 높다. 레이더 강우량은 대기 중 강수입자에 대한 레이더 반사도와 강우강도의 Z-R 관계식으로 추정되기 때문에 강우 추정 과정에 불확실성을 내포하고 있다. 특히, 우리나라의 여름철 한반도의 집중호우는 층운형 강우와 함께 대류형 강우가 동반되는 복합적인 강우시스템에서 자주 발생하지만, 레이더 강우는 일반적으로 단일 강우시스템에 대한 고정된 Z-R 관계식으로 추정하므로, 이러한 현상에 대해 과대 추정 혹은 과소 추정이 발생한다. 본 연구에서는 집중호우에 적합한 강우를 추정하기 위해 2021년 8월 21일부터 8월 25일까지 경남 호우사례를 대상으로 층운형, 대류형, 열대형의 Z-R관계식과 반사도 조건에 따라 층운형과 적운형을 구분하여 Z-R 관계식을 적용하여 레이더 강우량 자료를 산출하였으며, 지상강우자료를 이용하여 정확도를 평가하였다. 레이더 자료 처리를 위해 Radar Software Library (RSL)를 이용하여 수평으로 1km 해상도의 1.5km CAPPI (Constant Altitude Plan Position Indicator) 자료로 변환하였다. 레이더 강우 추정의 정확도를 평가하기 위해 레이더 지점으로부터 100 km 이내에 위치하고 있는 기상관서와 자동기상관측소의 강우관측 결과와 비교·분석하였다.

• International Journal of Knowledge Content Development & Technology
• /
• v.13 no.2
• /
• pp.23-35
• /
• 2023

Word templates exist for select journals, and their primary objective is to facilitate submissions to those journals, thereby optimizing editors' and publishers' time and resources by ensuring that the desired style (e.g., of sections, references, etc.) is followed. However, if multiple unrelated authors use the exact same template, a risk exists that some text might be erroneously cloned if template-based papers are not carefully screened by authors, journal editors or proof copyeditors. Elsevier Procedia® was used as an example. Select cloned text, presumably derived from MS Word templates used for submissions to Elsevier Procedia® journals, was assessed using Science Direct. Typically, in academic publishing, identical text is screened using text similarity software during the submission process, and if detected, may be flagged as plagiarism. After searching for "heading should be left justified, bold, with the first letter capitalized", 44 Elsevier Procedia® papers were found to be positive for vestigial template text. The integrity of the information in these papers has been compromised, so these errors should be corrected with an erratum, or in the case of extensive errors and vast tracts (e.g., pages long) of template text, papers should be retracted and republished.

• KNOM Review
• /
• v.22 no.3
• /
• pp.31-39
• /
• 2019

This paper introduces our research results of SDN/SON-based emergeny communications system for nuclear power plant under extreme natural diaster like Fukusima nuclear power plant incident. In such a extreme situation, nuclear power plant operational staffs which do not have technical knowledge of network provisioning and operations have to deploy the emergency network. Thus our proposed system provides capabilities to provision an emergency network autonomically and enable voice and data services. It also describes our PoC system developed based on the proposed core technology and architecture with the results of system verification testing.