• 한국연소학회지
• /
• 제13권2호
• /
• pp.1-6
• /
• 2008

An experimental study of the flame response in a turbulent premixed combustor has been conducted with room temperature, atmospheric pressure inlet conditions using premixed natural gas. The fuel is premixed with the air upstream of a choked inlet to avoid equivalence ratio fluctuations. Therefore the observed flame response is only the result of the imposed velocity fluctuations, which are produced using a variable speed siren. Measurements are made of the velocity fluctuation in the nozzle using hot wire anemometry and of the heat release fluctuation in the combustor using chemiluminescence emission. The results are analyzed to determine the phase and gain of the flame transfer function as a function of the modulation frequency. Of particular interest is the effect of flame structure on the flame response predictions and measurements. The results show that both the gain and the phase of flame transfer function are closely associated with the flame length and structure, which is dependent upon the upstream flow perturbation as well as equivalence ratio in the current study.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.247-252
• /
• 2008

This paper presents an active vibration control of cantilever beams under disturbances by a primary force. A direct velocity feedback control using a pair of PZT actuator and a velocity sensor is considered. Variation of the stability and performance with the locations of the sensor/actuator pair is investigated. It is found that the maximum gain varies with the locations of the sensor/actuator pair significantly. The maximum gain shows a symmetric distribution along the beam length with respect to the center point, although the boundary condition of the beam is unsymmetric. The control performance is affected by the location of the primary force as well as the location of the sensor/actuator pair. The active control system can more effectively reduce the vibration when the primary force is located close to the fixed boundary.

• Journal of Welding and Joining
• /
• 제8권1호
• /
• pp.23-30
• /
• 1990

The robotic welding has been adapted positively in many welding shops forthe purpose of improving the welding efficiency and liberating operators from the severe working atmosphere. But for a large-size structure with thick plates like ship-building and every kind of plants manufacturing, the application of the arc welding robots is not established yet. The reason is assumed that the conventional arc welding robots are not adaptive for multi-pass welding of thick plates whose grooves are not so accurate. As one solution to this problem, a guidance system which uses the welding arc itself as a sensor is largely used. In this study the velocity controller which changes the tip to workpiece distance for regulating the weld proposed. The proportional and integral gain of velocity controller were determined by using the computer simulation of the control system, and the simulation results compared with the experimental ones. It was revealed that the developed control system using the arc sensor principle has a good capability of tracking the weld joint, although some more studies will be needed to refine the model of arc current.

• 전자공학회논문지
• /
• 제54권7호
• /
• pp.127-132
• /
• 2017

이 논문에서는 모델 기반 설계에 근거한 이륜 도립진자 로봇의 제어이득을 설계하고 NXT 마인드스톰과 RobotC 언어를 이용하여 수업에 활용 가능한 로봇을 제작 및 실험한다. 이륜 도립진자 로봇은 NXT 마인드스톰, 서보 직류전동기, 자이로 센서, 가속도 센서로 구성된다. 직류전동기에 내장된 엔코더를 이용하여 바퀴의 회전각을 검출하며 이동평균을 이용하여 바퀴의 회전각속도를 계산한다. 자이로 센서는 몸체의 피치 각속도를 측정하며 가속도 센서는 몸체의 피치 각도를 측정한다. 자이로와 가속도의 센서 융합을 통해 몸체 각도를 계산한다. 제어기 이득 요소는 휠 각도, 휠 각속도, 몸체 피치 각도, 몸체 피치 각속도에 대한 가중치이다. 이들 제어이득의 변화에 따른 도립진자 로봇의 변화를 실험하며 유용성을 확인한다.

• 한국소음진동공학회논문집
• /
• 제18권12호
• /
• pp.1293-1300
• /
• 2008

This paper presents an active vibration control of cantilever beams under disturbances by a primary force. A direct velocity feedback control using a pair of PZT actuator and a velocity sensor is considered. Variation of the stability and performance with the locations of the sensor/actuator pair is investigated. It is found that the maximum gain varies with the locations of the sensor/actuator pair significantly. The maximum gain shows a symmetric distribution along the beam length with respect to the center point, although the boundary condition of the beam is unsymmetric. The control performance is affected by the location of the primary force as well as the location of the sensor/actuator pair. The active control system can more effectively reduce the vibration when the primary force is located close to the fixed boundary.

• 로봇학회논문지
• /
• 제15권3호
• /
• pp.212-220
• /
• 2020

This paper deals with a strategy of gain optimization for the kinematic control algorithm of a wire-driven surgical robot. The proposed controller consists of the closed-loop inverse kinematics with the back-calculation method. The closed-loop inverse kinematics has 18 PID control gains, and the back-calculation method has 6 gains. An efficient strategy is designed to optimize 18 values first and then the remaining 6 values. The optimal gain sets are searched under the step input with performance indices. In this gain optimization, the objective function is defined as the minimum value of signal-to-noise ratio of the performance indices for 6 DoF (Degree-of-Freedom) motion that is based on the Taguchi method, and the constraints are applied to obtain stable responses for each motion evenly. The gain sets obtained are verified by simulations using the test trajectories. In comparative results, the optimal gain value based on the performance index combined with ISE (integral of square error) and settling time showed the best control performance.

• 한국정밀공학회지
• /
• 제16권6호
• /
• pp.25-35
• /
• 1999

This paper presents a control gain tuning scheme for multi-axis PID control systems by Taguchi method. As an experimental set-up, a parallel mechanism machine tool has been selected. This machine has eight servodrives and each servodrive has four control gains, respectively. Therefore, total 32 control gains have to be tuned. Through a series of design of experiments, an optimal and robust set of PID control gains is tuned. The index of the sum of position error and velocity error is reduced to 61.4% after the experimental gain tuning regardless of the feedrate variation.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.442-448
• /
• 2008

This paper presents an approach to define an optimal piezoactuator length to actively control structural vibration. The optimal ratio of the piezoactuator length against beam length when a pair of piezoceramic actuator and accelerometer is used to suppress unwanted vibration with direct velocity feedback (DVFB) control strategy is not clearly defined so far. It is well known that direct velocity feedback (DVFB) control can be very useful when a pair of sensor and actuator is collocated on structures with a high gain and excellent stability. It is considered that three different collocated pairs of piezoelectric actuators (20, 50 and 100 mm) and accelerometers installed on three identical clamped-clamped beams (300 * 20 * 1 mm). The response of each sensor-actuator pair requires strictly positive real (SPR) property to apply a high feedback gain. However the length of the piezoactuator affects SPR property of the sensor-actuator response. Intensive simulation and experiment shows the effect of the actuator length variation is strongly related with the frequency range of SPR property. A shorter actuator gave a wider SPR frequency range as a longer one had a narrower range. The shorter actuator showed limited control performance in spite of a higher gain was applied because the actuation force was relatively small. Thus an optimal length ratio (actuator length/beam length) was suggested to obtain relevant performance with good stability with DVFB strategy. The result of this investigation could give important information in the design of active control system to suppress unwanted vibration of smart structures with piezoelectric actuators and accelerometers.

• Transactions on Control, Automation and Systems Engineering
• /
• 제4권1호
• /
• pp.38-42
• /
• 2002

Conditions are discussed for operating a dissymmetric human master-small (or micro) slave system in best (large position gain-small velocity gain) conditions allowing higher operator dexterity when real effects (joint compliance, link flexion delay and transmission distortion) are taken into account. It is shown that position PD feedback law advantage for ideal case no longer holds, and that more complicated feedback law depending on real effects has to be implemented with adapted transmission line. Drawback is slowdown of master slave interaction, suggesting to use more advanced predictive methods for the master and more intelligent control law for the slave.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 춘계학술대회 논문집
• /
• pp.469-470
• /
• 2008