• International Journal of Air-Conditioning and Refrigeration
• /
• v.15 no.4
• /
• pp.147-155
• /
• 2007

Mobile air conditioning systems work under widely changing operating conditions. To understand the system behavior under such dynamic conditions, a test facility that can impose transient loads as well as conducting dynamic measurements is needed. To test mobile air conditioning systems including their dynamic performance under various drive cycle patterns without using full scale vehicles in a wind tunnel, a new test facility, called "dynamic simulator," is described. It can replicate real vehicle operating conditions by interacting with the system being tested based on the measured system performance and subsequently adjusting the air properties returning to the test system based on the results of a numerical cabin model. A new dynamic simulator has been designed, constructed, and verified for performing dynamic tests. It was successful in controlling the temperature and relative humidity of the air returning to the test unit within ${\pm}0.7^{\circ}C$ and ${\pm}4%$ of their respective intended values. The verification test under the New European Driving Cycle demonstrated that detailed transient behavior of the mobile air conditioning system could be measured by using this dynamic simulator.

• Journal of the Ergonomics Society of Korea
• /
• v.31 no.5
• /
• pp.637-646
• /
• 2012

Objective: The aim of this study was to develop the adaptive device for severe physical disabilities using smart device in the driving simulator and its performance evaluation. Development of appropriate driving adaptive device for the people with serious physical limitation could contribute to maintain their community mobility. Background: There is lack of adaptive driving devices for the people with disabilities in Korea. However, if smart device systems like iPod and iPhone are used for driving a car, the people with serious physical limitations can improve their community mobility. Method: Both gyroscope and accelerometer from iPod were used to measure the tilted angle of the smart device for driving. Customized Labview program was also used to control three axis motors for steering wheel, accelerator and brake pedals. Thirteen subjects were involved in the experiment for performance evaluation of smart device in simulator. Five subjects had driver licenses. Another four subjects did not have driver licenses. Others were people with disabilities. Results: Average driving score of the normal group with driver license in the simulator increased 46.6% compared with the normal group without driver license and increased 30.4% compared with the disabled group(p<0.01). There was no significant difference in the average driving score between normal group without driver license and disabled group(p>0.05). Conclusion: The normal group with driver license showed significantly higher driving score than other groups. The normal group without driver license and disabled group could improve their driving skills with training in simulator. Application: If follow-up studies would be continued and applied in adapted vehicle for on road environment, many people with more severe disabilities could drive and improve the quality of life.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.4
• /
• pp.447-456
• /
• 2010

The application of a reliable motion simulator can contribute effectively in the evaluation of the performance of a vehicle platform in the development stage of a small unmanned aerial vehicle (UAV). Therefore, the research on a reliable motion simulator can accelerate the development of UAV and decrease the relevant cost. In this paper, the design factors considered in the preliminary design stage of a 6 degree-of freedom motion simulator are defined and the motion range of the simulator is described on the basis of these design factors. The length, acceleration, and the required thrust of actuators with respect to the motion simulator under development are also predicted. The motion range can be increased and a suitable actuator can be selected and produced by applying these results in the manufacturing process of the motion simulator. Thus, the reliability of the motion simulators can be achieved during the actual design operation of the UAV.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.6
• /
• pp.222-230
• /
• 1999

A fixed type driving simulator is constructed with a car body, beam projector, operation software , driving scenario, and audio equipments. With the simulator, the cognitive effects of fatigue due to two hour continuous driving of a straight road is investigated . The effects of alcohol on driving performance is also studied. The braking operation and lane keeping performance due to fatigue and alcohol are investigated. Changes of vehicle motion due to these effects are verified by computer simulation.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.11
• /
• pp.535-540
• /
• 2003

Since axial flux motor has an advantage over more conventional radial flux type motor such as high power density, it can be used as a power train for hybrid electric vehicle and electric vehicle. Also operating range can be extended and efficiency can be improved by changing air gap. Optimal operating air gap is estimated based on the measured efficiency at different air gap. Motor model is developed based on estimated optimal air gap and efficiency. Motor/controller performance is analyzed through simulation. Possible application area of axial flux motor was explored through simulation.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.4
• /
• pp.930-937
• /
• 2013

In this paper, a motor control algorithm for performing a mode change without an integrated starter generator (ISG) is suggested for the automatic transmission-based hybrid electric vehicle (HEV). Dynamic models of the HEV powertrains such as engine, motor, and mode clutch are derived for the transient state during the mode change, and the HEV performance simulator is developed. Using the HEV performance bench tester, the characteristics of the mode clutch torque are measured and the motor torque required for the mode clutch synchronization is determined. Based on the dynamic models and the mode clutch torque, a motor torque control algorithm is presented for mode changes, and motor control without the ISG is investigated and compared with the existing ISG control.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.12
• /
• pp.6090-6097
• /
• 2013

A pneumatically-driven driving simulator that provides a realistic representation of the driving environment was developed. The motion platform for the driving simulator is a mechatronic device that gives a driver the realistic feeling of an actual vehicle. The cost of the motion platform comprises the largest part of the expenses in developing a driving simulator. In this project, to develop a low-cost motion platform, the self-built motion platform based on the Stewart platform configuration that is constructed by six pneumatic cylinders was used as its actuator. The Stewart platform that moves in response to the operating signals of the joystick showed satisfactory tracking performance. We confirmed the possibility of the driving simulator using rFactor that is a commercially available racing game software.

• Journal of Drive and Control
• /
• v.20 no.4
• /
• pp.17-26
• /
• 2023

A forklift is an industrial vehicle that lifts or transports heavy objects using a hydraulically operated fork, and is equipped with an automatic transmission for the convenience of repetitive transportation, loading, and unloading work. The Transmission Control Unit (TCU) is a key component in charge of the shift control function of an automatic transmission. It consists of an electric circuit with an input/output signal interface function and firmware running on a microcontroller. To develop TCU firmware, the development process of shifting algorithm design, firmware programming, verification test, and performance improvement must be repeated. A simulator is a device that simulates a mechanical system having dynamic characteristics in real time and simulates various sensor signals installed in the system. The embedded transmission simulator is a simulator that is embedded in the TCU firmware. information related to the mechanical system that is necessary for TCU normal operation. In this study, an embedded transmission simulator applied to the originally developed forklift TCU firmware was designed and used to verify various forklift shift control algorithms.

• Journal of the Society of Naval Architects of Korea
• /
• v.61 no.4
• /
• pp.216-225
• /
• 2024

The sliding mode controller has characteristics that ensure stability and robustness against system uncertainty and disturbance. However, chattering occurs in the control inputs to compensate for system uncertainties and ensure that the system operates efficiently on the sliding surface. When the disturbance is large, using a sliding mode controller requires a large control gain value, which also increases chattering and reduces performance. Therefore, in this study, a nonlinear disturbance observer was used to compensate for external disturbances such as currents and waves and uncertainty in the control system for autonomous underwater vehicles. Accordingly, a robust controller can be implemented while reducing the control gain. The disturbance observer serves to ensure that the behavior of the actual system is closer to the nominal model by compensating for uncertainties between the actual system model and the nominal model during the control process. Therefore, the simulation results show that the performance and robustness of the autonomous underwater vehicle controller are improved by introducing a disturbance observer.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1132-1137
• /
• 2007

This paper describes a Unified Chassis Control (UCC) strategy to prevent vehicle rollover by integrating individual modular chassis control systems such as Electronic Stability Control (ESC) and Continuous Damping Control (CDC). The UCC threshold is determined from a rollover index computed by estimated roll angle, roll rate and measured lateral acceleration. A direct yaw moment control method is used to design the ESC based on a 2-D bicycle model. Similarly, the CDC is designed based on a 2-D roll model using a direct roll moment control method. The performance of the proposed UCC scheme is investigated and compared to that of modular chassis controllers through computer simulations using a validated vehicle simulator. It is shown that the proposed the UCC can lead to improvements in vehicle stability and efficient actuation of chassis control systems.