• Journal of Aerospace System Engineering
• /
• v.10 no.1
• /
• pp.59-65
• /
• 2016

Korea Aerospace Research Institute (KARI) is developing an electric-driven HALE UAV in order to secure system and operational technologies since 2010. Based on the 5 years of flight tests and design experiences of the previously developed electric-driven UAVs, KARI has designed EAV-3, a solar-powered HALE UAV. EAV-3 weighs 53 kg, the structure weight is 21 kg, and features a flexible wing of 19.5 m in span with the aspect ratio of 17.4. Designing the main wing and empennage of the EAV-3 the amount of the bending due to the flexible wing, 404 mm at 1-G flight condition based on T-800 composite material, and side wind effects due to low cruise speed, V_cr = 6 m/sec, are carefully considered. Also, unlike the general aircraft there is no center of gravity shift during the flight. Thus, the static margin cuts down to 28.4% and center of gravity moves back to 31% of the Mean Aerodynamic Chord (MAC) comparing to the previously developed scale-down HALE UAVs, EAV-2 and EAV-2H, to minimize a trim drag and enhance a performance of the EAV-3. The first flight of the EAV-3 has successfully conducted on the July 29, 2015 and the test flight above the altitude 14 km has efficiently achieved on the August 5, 2015 at the Goheung aviation center.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.25 no.3
• /
• pp.125-130
• /
• 2019

Shock and vibration inputs are transmitted from the vehicle through the packaging to the fruit. Inside, these cause sustained bouncing of fruits against each other and container wall. These steady state vibration input may cause serous fruit injury, and this damage is particularly severe whenever the fruit inside the package is free to bounce, and is vibrated at its resonance frequency. The determination of the resonance frequencies of the fruit and vegetables may help the packaging designer to determine the proper packaging system providing adequate protection for the fruit, and to understand the complex interaction between the components of fruit when they relate to expected transportation vibration inputs. Instrumentation and technologies are described for determining the vibration response characteristics of the pears for exporting with frequency range from 10 to 200 Hz, sweep rate of 1 octave/min, sweep method of logarithmic up and down and acceleration levels of 0.2, 0.4, 0.6, 0.8 and 1.0 G considering the domestic transportation environment. The resonance frequency of the pears ranged from 49.04 to 87.16 Hz and the amplitude at resonance was between 0.96 and 4.02 G in test frequency band and acceleration level. The resonance frequency and amplitude at resonance frequency band of the pears decreased with the increase of the sample mass. The multiple nonlinear regression equations for predicting the resonance frequency of the pears were developed using the independent variables such as mass, input acceleration.

• Toxicological Research
• /
• v.23 no.4
• /
• pp.373-382
• /
• 2007

This study was conducted to obtain acute information of the oral dose toxicity of PGB-1, a novel polyglucosamine polymer produced from a new strain Enterobacter sp. BL-2 in male and female mice. In order to calculated 50% lethal dose ($LD_{50}$) and approximate lethal dose (LD), test material was once orally administered to male and female ICR mice at dose levels of 2000, 1000, 500, 250, 125 and 0 (vehicle control) ml/kg (body wt.). The mortality and changes on body weight, clinical signs, gross observation and organ weight and histopathology of principle organs were monitored 14 days after dosing with PGB-1. We could not find any mortalities, clinical signs, body weight changes and gross findings. In addition, significant changes in the organ weight and histopathology of principal organs were not observed except for some sporadic findings. The results obtained in this study suggest that PGB-1 may not be toxic in mice and may be therefore safe for clinical use. The $LD_{50}$ and approximate LD in mice after single oral dose of PGB-1 were considered over 2000 mg/kg in both female and male mice.

• Journal of Korean Society of Transportation
• /
• v.20 no.5
• /
• pp.163-174
• /
• 2002

Speeding has been reported as one of the major causes for fatal traffic accidents in Korea. The resolution against this dangerous speeding comes to make the automated speed enforcement system an enforcement tool. The speed detection device, which measures speeds of each incoming vehicles using double loop sensors, requires high accuracy. The object of this study is to develop an accurate speed measurement algorithm using double loop detectors. Some important findings are summarized as follows: 1) It was found that speed measurement errors are caused by scanning rate, distance of two loops, irregular vehicle trajectories, multiple vehicles in detection zone. 2) A proposed algorithm using two signal set proved to reduce variance as well as mean of speed measurement. 3) A proposed filtering algorithm was effective to filter irregular driving vehicles and multiple vehicles in detection zone. A comprehensive field test of developed algorithm resulted in significant improvement of speed measurement accuracy.

• Journal of Korean Society of Transportation
• /
• v.30 no.5
• /
• pp.83-90
• /
• 2012

Driver ordinarily takes sudden braking when urgent situation is developed or when the vehicle is involved in an unexpected accident. Therefore, the most common trace at a traffic accident scene is skid mark. Currently, in investigating traffic accident, overspeed is determined by the length of skid mark. However, in order to identify accurate cause of accident, estimation of pre-braking speed which takes into account speed reduction during transient time should be considered as a requirement. In a recent study, several ways to estimate pre-braking speed were suggested, but none considered to differentiate the decelerating transient brake section and skidding section. This study analyzed trends of decelerating transient brake section and skidding section by real braking test.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.8
• /
• pp.946-952
• /
• 2013

Large scale fire tests were conducted to develop water mist nozzles as a component of fixed water- based fire fighting systems for Ro-Ro spaces and special category spaces. Fire scenarios for this system consist of two cases which are for cargo fire in a simulated truck and for passenger vehicle fire, and each case has 3 different tests according to the position between fixed water mist nozzles and fire source. Every experiment proceeded for 30 minutes and acceptance criteria were based on gas temperature, fuel package's damage and ignition of targets. This study primarily dealt with the experimental results of cargo fire and focused on fire suppression capability in accordance with discharge pressure, flow rate and flow characteristics like swirl and penetration of the developed water mist nozzles. It appeared that low pressure water mist nozzles with about 40 L/min were able to control fire occurred in Ro-Ro spaces.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.8
• /
• pp.835-841
• /
• 2012

We measured the mechanical and thermal properties of four types of cast irons used for manufacturing the brake discs of railway vehicles. It was found that these properties could be controlled by varying the composition of Ni, Cr, and Mo. Thermal fatigue tests were carried out by using a thermal fatigue tester in which thermal cycles could be controlled. Thermal crack initiation and propagation were measured on cylindrical specimens. Finally, we simulated the thermal fatigue test procedure by finite element analysis and calculated the thermal fatigue lifetimes by Manson-Coffin's equation and the maximum principal strain. The estimated thermal fatigue lifetimes corresponded to the measured lifetimes when the total crack length was $40{\mu}m{\sim}1mm$.

• Journal of Korean Academy of Nursing
• /
• v.43 no.2
• /
• pp.145-153
• /
• 2013

Purpose: The purpose of this manuscript is to discuss the need for use of evidence based practice (EBP) in LTC, the current use of evidence in long term care facilities and what we know about adoption of the use of EBP in LTC. Methods: Literature review and reporting of findings from the M-TRAIN study that was a quasi-experimental design to test the effectiveness of an intervention to increase the use of EBPs for urinary incontinence and pain in 48 LTC facilities. Results: Barriers to adopting EBPs include lack of available time, lack of access to current research literature, limited critical appraisal skills, excessive literature to review, non-receptive organizational culture, limited resources, and limited decision-making authority of staff to implement change. Strategies to promote adoption of EBP include the commitment of management; the culture of the home; leadership; staff knowledge, time, and reward; and facility size, complexity, the extent that members are involved outside the facility, NH chain membership, and high level of private pay residents. Findings from the M-TRAIN add, stability of nurse leader and congruency between the leaders perception of their leadership and the staff's perception of the leadership. Conclusion: There is clear evidence of the need and the benefits to residents of LTC and to the health care system yet adoption of EBP continues to be slow and sporadic. There is also evidence for the process of establishing best evidence and many resources to find the available EBPs. The urgent need now is finding ways to best get the EBPs implemented in LTC. There is growing evidence about best methods to do this but continued research is needed. Clearly, residents in LTC deserve the best care possible and EBPs represent an important vehicle by which to do this.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.6
• /
• pp.916-921
• /
• 2018

Recently, interest in autonomous vehicle has increased, and autonomous driving capability is also increasing. Depending on the autonomous driving ability, the maximum number of steps is divided into 6 steps. The higher the step, the less the involvement of the person in the running, and the person does not need to be involved at the highest stage. Today's autonomous vehicles have been developed high level, but solutions are not clearly defined in case of an accident, so only the test run is possible. Such an accident occurring during traveling is almost inevitable, and it is judged who has made a mistake in case of an accident, which increases the punishment for the accident. Although a black box is used to clarify such a part, it is easy to delete a record, and it is difficult to solve an accident such as a hit-and-run. In this paper, i design a driving record system using black chain to solve accidents.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.114.2-114.2
• /
• 2017

Transparent film heaters (TFHs) based on Joule heating are currently an active research area. However, TFHs based on an indium tin oxide (ITO) monolayer have a number of problems. For example, heating is concentrated in part of the device. Also, heating efficiency is low because it has high sheet resistance ($R_S$). Resistance of indium zinc oxide (IZO) is similar to ITO and it can be used to flexible applications due to its amorphous structure. To solve these problems, our study introduced hybrid layers of IZO/Ag/IZO deposited by magnetron sputtering, and the electrical, optical, and thermal properties were estimated for various thickness of the metal interlayer. It was found that the sheet resistance of the multilayer was mainly dependent on the thickness of the Ag layers. The $R_S$ of IZO(40)/Ag/IZO(40nm) multilayer was 5.33, 3.29, $2.15{\Omega}/{\Box}$ for Ag thickness of 10, 15, and 20nm, respectively, while the $R_S$ of an IZO monolayer(95nm) was $59.58{\Omega}/{\Box}$. The optical transmittance at 550nm for the IZO(95nm) monolayer is 81.6%, and for the IZO(40)/Ag/IZO(40nm) multilayers with Ag thickness 10, 15 and 20nm, is for 72.8, 78.6, and 63.9%, respectively. The defrost test showed that the film with the lowest RS had the highest heat generation rate (HGR) for the same applied voltage. The results indicated that IZO(40)/Ag(15)/IZO(40nm) multilayer has the best suitable property, which is a promising thin film heater for the application in vehicle windshield.