• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.123-126
• /
• 2002

Acoustic vibration analysis has been performed using random vibration analysis module of MSC/NASTRAN to evaluate the safety of the composite satellite antenna structure under the acoustic pressure from the launch vehicle. It was found that maximum $3\sigma$ stress by acoustic excitation was less than allowable stress.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.155-158
• /
• 2005

Sub-frame is a key component to damp the vibration of engine-born and isolate the input force from a ground. To enhance the performance of the sub-frame of vehicle, its structure should be designed to be a high performing mechanical filter that exclude the low frequency vibration elements. In this paper, a contribution analysis based on the frequency response function(FRF) is introduced to detect a high sensitive position of the target sub-frame and its results are validated with a SDM(structural dynamic modification) analysis.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.702-706
• /
• 2009

Internal running noise of a vehicle running in open field is the summation of air borne noise and structure-borne noise. In this paper vibration damping characteristics of carbody are investigated to see the effect of sound-deadening paint on the internal running noise. By using SEA method, vibration levels of complete train with and without sound-deadening paint are estimated and structure borne noise levels are estimated.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.441-446
• /
• 2008

The source transfer receiver model ('Source $\times$ Transfer = Response' model) which is widely used by NVH development process of vehicle/transport/machinery to analyze effectively and manage efficiently the structural dynamic behavior is also applicable to construction structure. If the evaluation assessment of the vibration level does not meet the target level, there are two methods, one is source treatment or replacement and the other is the reduction treatment on the transfer structure. In case of source treatment, it is done by source supplier and so, the latter is more practical method to reduce the vibration level. In this study, in order to get the accurate Transfer FE model(floor structure FE model), Experimental modal analysis of part of floor structure and FEM modal analysis of full floor structure are performed, then updating of FE model is performed after correlation analysis between these two results and finally, the modal model and FRF are compared between FE and Experimental results.

• 한국소음진동공학회논문집
• /
• 제24권8호
• /
• pp.606-612
• /
• 2014

Vehicle simulation models for noise and vibration prediction have been developed so far generally in two schemes. One is FE models generally used for problems below 200 Hz such as booming noise, and the other is SEA models for high frequencies of more than 1 kHz, representatively related to sound packages. There have been many researches to develop a simulation model for 200~1000 Hz, so-called mid-frequency region, and this paper shows one practical result that covers the trimmed body of a sedan vehicle. The simulation model is developed based on an FE model, and then FE elements at some areas are substituted with SEA elements to reduce DOFs. SEA panels are described by modal density, radiation efficiency, stiffness and damping characteristics that are found from some numerical assessments. Sound packages are modeled similarly as a conventional SEA model. The results obtained from the hybrid model were compared to experimental results. Predicted pressure and vibrational velocity generally show a good agreement. The developed simulation model and related technology are successfully being used in vehicle development process.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2006년도 정기 학술대회 논문집
• /
• pp.772-777
• /
• 2006

An acoustic finite element model of a bridge is developed to evaluate the noise generated by the traffic-induced vibration of the bridge. The dynamic response of a multi-girder bridge, modeled by a 3-dimensional frame element model, is analyzed with a 3-axle(8DOF) truck model and a 5-axle(l3DOF) semi-trailer. The flat plate element is used to analyze the acoustic pressure due to the fluid-structure interactions between the vibrating surface and contiguous acoustic fluid medium. The radiation fields of noise with a specified distribution of vibrating velocity and pressure on the structural surface are also computed using the Kirchhoff-Helmholtz integral. In an attempt to illustrate the influence of the structural vibration noise of a bridge to total noise level around the bridge, the random function is used to generate the vehicle noise source including the engine noise and the rolling noise interacting between the road and tire. Among the diverse parameters affecting the dynamic response of bridge, the vehicle velocity, the vehicle weight, the spatial distribution of the road surface roughness, the stiffness degradation of the bridge and the variation of the air temperature changing the air density are found to be the main factors that increase the level of vibration noise. Consequently, The amplification rate of noise increases with the traveling speed and the vehicle weight.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2000년도 봄 학술발표회논문집
• /
• pp.297-303
• /
• 2000

Damage estimation of a bridge structure is presented using ambient vibration data caused by the traffic loadings. The procedure consists of identification of the modal properties and assessment of the damage locations and severities. An experimental study is carried out on the bridge model subjected to vehicle loadings. Vertical accelerations of the bridge deck are measured at a limited number of locations. The modal parameters are identified from the free vibration signals extracted using the random decrement method. Then, the damage assessment is carried out based on the estimated modal parameters using the neural networks technique. The identified damage locations and severities agree reasonably well with the inflicted damages on the structure.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.266-269
• /
• 2006

Tire is in charge of a lot of function, which is supporting vehicle load, transferring traction and. brake, absorbing impact by road etc. As the silence of vehicle increase more important, the importance of tire noise is more raised. In recent, the study on reduction of tire noise is generally processed. Tire noise is divided in structure home noise and all borne noise. Tire tread properties have a lot of multiplicity. Rubber properties are caused by changing or tread hardness. That change Elastic Modulus and Loss Modulus, which is related by tire noise. In the study, we found that road noise is affected by tread hardness

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2011년도 춘계학술논문집 2부
• /
• pp.529-532
• /
• 2011

A theoretical model has been studied to describe the sound radiation analysis for structure vibration noise of vehicle tires under the action of random moving line forces. When a tire is analyzed, it had been modeled as curved beams with distributed springs and dash pots that represent the radial, tangential stiffness and damping of tire, respectively. The reaction due to fluid loading on the vibratory response of the curved beam is taken into account. The curved beam is assumed to occupy the plane y=0 and to be axially infinite. The expression for sound power is integrated numerically and the results examined as a function of Mach number, wave-number ratio and stiffness factor. The experimental investigation for structure vibration noise of vehicle tire under the action of random moving line forces has been made. Based on the Spatial Transformation of Sound Field techniques, the sound power and sound radiation are measured. Results strongly suggest that operation condition in the tire material properties and design factors of the tire govern the sound power and sound radiation characteristics.

• 한국소음진동공학회논문집
• /
• 제25권11호
• /
• pp.747-752
• /
• 2015

Underwater radiated noise is an important characteristic in the naval weapon systems. It is difficult to measure the radiation efficiency of underwater vehicle, such as UUV(unmanned underwater vehicle) and underwater weapons in real operation environment. In this study, acoustic radiation efficiency of a circular cylindrical structure is measured in the laboratory-water tank. The radiation efficiency is compared with the numerical results and it is found that they are in a good agreement. Therefore, the measurement method can be applied effectively for predicting the underwater radiation noise and effectiveness of radiation reduction means.