• International Journal of Automotive Technology
• /
• v.3 no.4
• /
• pp.165-170
• /
• 2002

For a vehicle Anti-lock Braking System (ABS), the control target is to maintain friction coefficients within maximum range to ensure minimum stopping distance and vehicle stability. But in order to achieve a directionally stable maneuver, tire side forces must be considered along with the braking friction. Focusing on combined braking and turning operation conditions, this paper presents a new control scheme for an ABS controller design, which calculates optimal target wheel slip ratio on-line based on vehicle dynamic states and prevailing road condition. A fuzzy logic approach is applied to maintain the optimal target slip ratio so that the best compromise between braking deceleration, stopping distance and direction stability performances can be obtained for the vehicle. The scheme is implemented using an 8-DOF nonlinear vehicle model and simulation tests were carried out in different conditions. The simulation results show that the proposed scheme is robust and effective. Compared with a fixed-slip ratio scheme, the stopping distance can be decreased with satisfactory directional control performance meanwhile.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.5
• /
• pp.2360-2366
• /
• 2011

The Unmanned Ground Vehicle is comprised of four systems of obstacle detection: The navigation system, vehicle controlling system, obstacle detecting and an integration system that use the various sensors. The research introduced utilizes 6 lasers to recognize obstacles. The system operates an avoidance system within the unmanned ground vehicle, using six lasers. The Unmanned Ground Vehicle's parallel parking and right angle parking is in development using algorithms. This algorithms' certification is intended to be installed in the encoder, in the GPS. By using the Laser Scannerfor the position's calculation, errors are both reduced and minimized, so the tire's slip minimized to the point where the vehicle had a limit of about 5Km/h.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.10
• /
• pp.1924-1934
• /
• 2011

This paper is concerned with the robustness evaluations of the guidance controller for a bimodal tram which is being developed by the Korea Railroad Research Institute (KRRI). The bimodal tram is an all-wheel steered multiple-articulated vehicle as a new kind of transportation vehicle. This vehicle has to be equipped with an automatic guidance system. In [1], such a controller has been recently proposed. However, since the performance is affected by weight change of the vehicle due to number of the passenger, model parameter uncertainties depending on the state of friction and the elasticity of the tire, and a typhoon, the controller designed must be examined with these conditions. As expected, because the vehicle dynamics is highly nonlinear, for the sake of investigating the robustness of the controller we compose two simulation ways based on the vehicle models which are implemented by the ADAMS and the MATLAB/LabVIEW toolboxes. Different uncertainties and a typhoon disturbance have been considered for the simulation conditions. Simulation results are shown.

• Journal of Drive and Control
• /
• v.16 no.4
• /
• pp.48-55
• /
• 2019

The Electronic Stability Program (ESP), a system that improves vehicle safety, also known as YMC (Yaw Motion Controller) or VDC (Vehicle Dynamics Control), is a system that operates in unstable or sudden driving and braking situations. Developing conditions such as unstable or sudden driving and braking situations in a vehicle are very dangerous unless you are an experienced professional driver. Additionally, many repetitive tests are required to collect reliable data, and there are many variables to consider such as changes in the weather, road surface, and tire condition. To overcome this problem, in this paper, hardware and control software such as the ESP controller, vehicle engine, ABS, and TCS module, composed of three control zones, are modeled using MATLAB/SIMULINK, and the vehicle, climate, and road surface. Various environmental variables such as the driving course were modeled and studied for the real-time ESP real-time simulator that can be repeatedly tested under the same conditions.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.3
• /
• pp.253-259
• /
• 2014

This study proposes a map-based control method to improve a vehicle's lateral stability, and the performance of the proposed method is compared with that of the conventional model-referenced control method. Model-referenced control uses the sliding mode method to determine the compensated yaw moment; in contrast, the proposed map-based control uses the compensated yaw moment map acquired by vehicle stability analysis. The vehicle stability region is calculated by a topological method based on the trajectory reversal method. The performances of model-referenced control and map-based control are compared under various road conditions and driving inputs. Model-referenced control uses a control input to satisfy the linear reference model, and it generates unnecessary tire lateral forces that may lead to worse performance than an uncontrolled vehicle with step steering input on a road with low friction coefficient. The simulation results show that map-based control provides better stability than model-referenced control.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.911-915
• /
• 2004

Recently, several experimental techniques for identifying the noise sources distributed over a moving vehicle are being developed and used in order to design a low noise vehicle. The beamforming method, which uses phase information between several microphones to localize the source position, is proved to be one of the promising techniques applicable even under complicated test environments. In this study a beamforming algorithm is developed and applied to measure the dominant noise sources on a passenger car moving at constant speed. Unlike the acoustic signals from a stationary noise source, the sound generated from a moving source is distorted due to the Doppler effects. The sound pressure are measured with an spiral array system composed of 26 microphones and a pair of photo sensors are used to measure the. vehicle speed. The information about the speed and relative position of the vehicle are used to eliminate the Doppler effects from the measured pressure signal by using a de-Dopplerization algorithm. The noise generated from a moving vehicle can be grouped in many ways, however, tire noise and the noise generated from the engine are distinguishable at the speeds being tested.

• Journal of ILASS-Korea
• /
• v.27 no.3
• /
• pp.155-160
• /
• 2022

Recently, major developed countries have strengthened automobile fuel efficiency regulations and carbon dioxide emission allowance standards to curb climate change caused by global warming worldwide. Accordingly, research and manufacturing on electric vehicles that do not emit pollutants during actual driving on the road are being conducted. Several automobile companies are producing and testing electric vehicles to commercialize them, but it takes a lot of manpower and time to test and evaluate mass-produced electric vehicles with driving mileage of more than 300km on a per-charge. Therefore, in order to reduce this, a simulation model was developed in this study. This study used vehicle information and MCT speed profile of small electric vehicle as basic data. It was developed by applying Simulink, which models the system in a block diagram method using MATLAB software. Based on the vehicle dynamics, the simulation model consisted of major components of electric vehicles such as motor, battery, wheel/tire, brake, and acceleration. Through the development model, the amount of change in battery SOC and the mileage during driving were calculated. For verification, battery SOC data and vehicle speed data were compared and analyzed using CAN communication during the chassis dynamometer test. In addition, the reliability of the simulation model was confirmed through an analysis of the correlation between the result data and the data acquired through CAN communication.

• Journal of Auto-vehicle Safety Association
• /
• v.16 no.1
• /
• pp.12-20
• /
• 2024

Side impact with MDB (moving deformable barrier) is common in side crash test protocols around the globe, most of which are quite similar to that of US NCAP side impact protocol but IIHS side impact protocol is considered to be the most harsh one due to the MDB's weight and impact speed. In this study US NCAP side impact and IIHS side impact test conditions are compared with respect to delta-V (impulse of the test vehicle), roll speed, and yaw speed as well as survival space (the smallest distance between the front driver seat cushion center to B pillar after the test). Error factors (friction between tire and ground, tolerance of vertical and longitudinal position of the MDB with respect to the test vehicle), which are resident in the test protocol is studied with respect to the global vehicle behavior (delta-V, roll, yaw) as well as survival space.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.7
• /
• pp.629-634
• /
• 2017

In the case of the UHP (Ultra high performance) tire that the demand has increased rapidly, compared with the commonly used tire, severe deformation has been observed because of the low aspect ratio. When repeated deformations are applied to the sidewall rubber, accumulated fatigue damage may cause fatigue failure. Thus, the evaluation of the durability of the tire sidewall rubber has become a very important issue to prevent accidents that occur while the vehicle is running. However, the research and design criteria for the durability performance of the tire sidewall rubber hardly exist. In this study, we suggest a lifetime prediction formula using strain energy density obtained by performing tensile tests and fatigue tests on two different kinds of the tire sidewall compounds. Additionally, the applicability of our findings for low fuel consumption tires was reviewed by converting the fatigue life of the sidewall rubber into the expected mileage of the tire.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.5
• /
• pp.820-830
• /
• 1989

The tire inflation and contact problem has been solved by a finite element method. The finite element formulation is derived from the equilibrium equations by the principle of virtual work in the form of an updated Lagrangian formulation for incremental analysis. Then, a contact formulation is added to the finite element formulation to calculate stress state of tire in contact with flat rigid road under the load due to the self-weight of a vehicle. In the finite element analysis, equations of effective material properties are introduced to analyze a plane strain model of the shell-like tire by considering the bending effect of reinforced steel cords. The proposed equations of effective material properties produced stress concentration around the edge of belt layers, which does not appear when other well-known equations of material properties are adopted. The result from the above algorithm demonstrates the validity of the formulation and the proposed equations for the effective elastic constants. The result fully interprets the cause of separation between belt layers by showing the stress concentration.