• Journal of the Korean Society of Clothing and Textiles
• /
• v.31 no.6 s.165
• /
• pp.955-965
• /
• 2007

Safety helmets are used widely in various industries by workers since they are legally required to wear them. However, thermal discomfort is one of the major complaints from helmet users. To relieve this problem, frozen gelled packs can be considered for use inside the helmets. In this paper, tests were performed on humans to evaluate the physiological strains of wearing safety helmets and to investigate the effects of using frozen gelled packs inside the helmets. Experiments were conducted in a climatic chamber of WBGT $33{\pm}1^{\circ}C$ under four differed experimental conditions: 1) not wearing a safety helmet(NH); 2) wearing a safety helmet with frozen gelled pack A(HA); 3) wearing a safety helmet with frozen gelled pack B(HB); and 4) wearing only a safety helmet(OH). The results were as follows. First, when comparing NH with OH, physiological responses such as $\bar{T}_{sk},\;T_r$, HR and sweat rate were significantly higher in OH and subjective sensations were reported as less hot and more comfortable than NH(p<.05). Second, in regard to the frozen gelled packs inserted inside the safety helmets, some physiological responses in HA were different from those in HB, according to the two different types of packs. HA was hotter, more uncomfortable and less exhausted than HB. However, result from both HA and HB were lower than those from OH in terms of temperature and humidity inside safety helmet, sweat rate, $T_r$ increase, heat storage(p<.05). When wearing safety helmets with frozen gelled packs, it was shown that heat strain can be alleviated. These results are expected to help millions of workers who complain that wearing safety helmets is uncomfortable and messy.

• Korean Journal of Environmental Agriculture
• /
• v.16 no.4
• /
• pp.295-303
• /
• 1997

To investigate the transformation characteristics of nitrogen and carbon from cow manure compost amended in soil under different moisture conditions, dynamics of nitrogen and carbon were determined periodically for 15 weeks of aerobic incubation at room temperature during July${\sim}$November, 1996. Cow manure compost matured with mixing saw dust was amended with the 4 ratios (0, 2, 4, 6%(wt/wt)) in Ap horizon soil, which collected from green house in Yesan, Chungnam. Moisture was controlled with 0.2, 0.3, 0.4, and 0.5 of mass water conte nt (${\theta}$m) to air dried soil, and water loss was compensated at every sampling. During incubation, soil pH was decreased continuously, that was caused by hydrogen generated from nitrification of ammonium nitrogen. And pH became higher with inclining cow manure compost amendment and water treatment, that meaned the increase of mineralization of organic-N to $NH_4\;^+-N$. Total nitrogen was reduced with increasing water content, but total carbon showed the contrast tendency with that of nitrogen. Therefore, C/N ratio slightly decreased in the low water condition (${\theta}$m 0.2) during incubation, but increased continuously in high water condition over ${\theta}$m 0.4. As a result, it was assumed that soil fertility is able to be reduced in the high water content over available water content. Nitrate transformation rate increased lasting in the low water content less than ${\theta}$m 0.3. Itdropped significantly in the first $2{\sim}3$ weeks of incubation over ${\theta}$m 0.4. In particular, nitrate was not detected in ${\theta}$m 0.5 of water content after the first $2{\sim}3$ weeks. In contrast, ammonium transformation was inclined with increasing water treatment. Nitrogen mineralization rate, which calculated with percentage ratio of (the sum of ex.$NH_4\;^+-N$ and $NO_3\;^--N$)/total nitrogen, was continuously increased in the low water content of ${\theta}$m 0.2 and 0.3. But it saw the different patterns in high water content over ${\theta}$m 0.4 that was drastically declined in the initial stage and then gradually inclined . From the above results, nitrogen transformation patterns differentiated decisively in water content between ${\theta}$m 0.3 and 0.4 in soil. Thus, it is very important for the maintain of suitable soil water content to enhance fertility of soil amended with manure compost. However, excess treatment of manure compost might enhance the possibility of contamination of small watershed and ground water around agricultural area.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.44 no.4
• /
• pp.45-56
• /
• 2016

In this study, an analysis has been conducted on the evaluation criteria of current G-SEED(Green Standard for Energy and Environmental Design) and on the 78 buildings, certified by G-SEED, for 3 years from November, 2012 to November, 2015. Based on the results of this analysis, four issues are driven and proposed hereinafter. Issue 1 : Nowadays, the psychological proportion of landscape architecture in building is getting greater than ever so that it shows reliable reduction of carbon dioxide. Therefore, so far as the eight kinds of buildings are concerned, the evaluation items of G-SEED must include those of landscape architecture mandatorily through its enlargement. Issue 2 : It is undesirable factor that inhibits precise evaluation on landscaping area to let other areas appraise landscape architecture because it requires outstanding professionalism. So, G-SEED should not only ensure landscaping professionalism for the correct evaluation but also let landscape area participate in assessing other areas. Issue 3 : Many previous researches turned out that landscape planting technique has excellent effect on saving energy and reducing temperature of buildings. Thus, landscape planting technique of landscape area is required to be one of the evaluation items of energy sector. Issue 4 : Tree management also has to be newly included as one of the evaluation factor for the maintenance relating to the landscape architecture. G-SEED, enacted and enforced by the Green Building Creation Support Act in 2013, surely is effective system to reduce carbon dioxide in buildings. This is a special Act in its nature that is superior to Construction Law and must be observed by all means to construct buildings. Under the umbrella of this legal system, various of researches and products are contributing to creating new jobs in construction area. However, it is a well-known fact that landscape architecture area has shown less interest on this Act than that of construction area. In conclusion, it is necessary that landscape industry should conduct continuous researches on G-SEED and pay more attention to the Act enough to harvest related products and enlarge its work area.

• Korean Journal of Poultry Science
• /
• v.42 no.3
• /
• pp.247-256
• /
• 2015

There are approximately 1,500 broiler farms in Korea, each raising 55,000 birds. Ninety-five percent of the farms are contracted with Integration Company. According to the Korean broiler performance index, broilers in Korea are marketed at 32 days with 1.52 kg of body weight. In contrast, the market age and body weight of broilers are 47 days/2.8 kg in the United States and 42 days/2.5 kg in Europe. Because of the younger market age of the Korean broiler, the pre-starter feed is important. Chicks exhibit poor absorption of dietary nutrients up to 7 days after hatching due to an immature digestive system and low enzyme secretion rate and activity. At the beginning of hatching, chicks obtain their nutrients from the egg yolk sac. It is highly recommended that chicks, after consuming the nutrients in the egg yolk sac, are given supplemented pre-starter feed to increase early growth rates and improve the performance of broiler production. Pre-starter nutrient requirements are not expressed in NRC, so Korean feeding standards for poultry and commercial breeding companies determine the nutrient requirements of pre-starter broiler chickens. Three approaches are followed to formulate specially designed pre-starter feeds for broiler chicks: (i) selective use of raw materials, (ii) proper standards of nutrient supply, and (iii) application of feed additives such as exogenous enzymes. In the selection of raw materials, those with high digestibility can be used. The absorption rate of carbohydrates in grains can be increased through feed processing at high temperature and high pressure. Soy proteins and fish meal can also be added as protein sources. As an energy source, vegetable oils are preferred over animal fats because of the former's high digestibility. It is suggested that the levels of proteins and amino acids are higher in pre-starter feed than in starter feed. With regard to energy, the sources of energy are more important than the levels of energy in feed. Feed additives such as exogenous enzymes can be used to improve nutrient digestibility. In addition, organic acids and plant extracts can be used as alternatives to animal growth promoters to stimulate immunity and prevent diseases. The growth performance of broilers is affected by various factors, such as management and disease control, in addition to the nutritional strategy; however, nutritional strategies play an important role in improving the productivity of broilers. Therefore, nutritional strategies, along with management and disease control, are required for improving the productivity of broilers in Korea.

• Korean Journal of Soil Science and Fertilizer
• /
• v.39 no.5
• /
• pp.274-279
• /
• 2006

The exact estimation of crop evapotranspiration containing reference or potential evapotranspiration is necessary for decision of crop water requirements. This study was carried out for the evaluation and application of various meteorological elements used for the calculation of reference evapotranspiration (RET) by FAO Penman-Monteith (PM) model. Meteorological elements including temperature, net radiation, soil heat flux, albedo, relative humidity, wind speed measured by meteorological instruments are required for RET calculation by FAO PM model. The average of albedo measured for crop growing period was 0.20, ranging from 0.12 to 0.23, and was slightly lower than 0.23. Determinant coefficients by measured albedo and green grass albedo were 0.97, 0.95 and standard errors were 0.74, 0.80 respectively. Usefulness of deductive regression models was admitted. To assess an influence of soil heat flux (G) on FAO PM, RET with G=0 was compared with RETs using G at 5cm soil depth ($G_{5cm}$) and G at surface ($G_{0cm}$). As the results, RET estimated by G=0 was well agreed with RET calculated by measured G. Therefore, estimated net radiation, G=0 and albedo of green grass could be used for RET calculation by FAO PM.

• Korean Journal of Materials Research
• /
• v.4 no.7
• /
• pp.759-766
• /
• 1994

Our investigation aimed to reduce the leakage current of $Ta_2O_5$ thin film capacitor by layering SnOz thin film layer under Ta thin film, thereby supplying extra oxygen ions from the $SnO_{2}$ underlayer to enhance the stoichiometry of $Ta_2O_5$ during the oxidation of Ta thin film. Tantalum was evaporated by e-beam or sputtered on p-Si wafers with various deposition temperatures and was oxidized by dry--oxygen at the temperatures between $500^{\circ}C$ and $900^{\circ}C$. Aluminum top and bottom electrodes were formed to make Al/$Ta_2O_5$/p-Si/Al or $Al/Ta_2O_5/SnO_2$p-Si/AI MIS type capacitors. LCR meter and pico-ammeter were used to measure the dielectric constants and leakage currents of the prepared thm film capacitors. XRD, AES and ESCA were employed to confirm the crystallization of the thin f~lm and the compositions of the films. Dielectric constant of $Ta_2O_5$ thin film capacitor with $SnO_{2}$ underlayer was found to be about 200, which is about 10 times higher than that of $Ta_2O_5$ thin film capacitor without $SnO_{2}$ underlayer. In addition, higher oxidation temperatures increased the dielectric constants and reduced the leakage current. Higher deposition temperature generally gave lower leakage current. $Ta_2O_5/SnO_2$ capacitor deposited at $200^{\circ}C$ and oxidized at $800^{\circ}C$ showed significantly lower leakage current, $10^{-7}A/\textrm{cm}^2$ at $4 \times 10^{5}$V/cm, compared to the one without $SnO_{2}$ underlayer. XRD showed that $Ta_2O_5$ thin film was crystallized above $700^{\circ}C$. AES and ESCA showed that initially the $SnO_{2}$, underlayer supplied oxygen ions to oxidize the Ta layer, however, Sn also diffused into the Ta thin film layer to form a new $Ta_xSn_YO_Z$ , ternary oxide layer after all.

• Journal of Life Science
• /
• v.21 no.2
• /
• pp.309-315
• /
• 2011

Rice syrup meal (RSM) was enzymatically hydrolyzed using eight commercial proteases (Protamex, Neutrase, Flavourzyme, Alcalase, Protease M, Protease N, Protease A, Molsin F) for 4 hr at optimum pH and temperature. Proteolytic hydrolysates were examined in supernatant and precipitate using Lowry protein assay, semimicro Kjeldahl method and gravimetric method using weight difference before and after enzymatic hydrolysis. Although RSM contains a high amount of protein (71.2%), only a very small amount of protein was hydrolyzed. Two proteases (Protease M and Protease N) were found to be the most effective in the hydrolysis of RSM protein. In Lowry method, 57.5 and 59.0 mg protein/g RSM were hydrolyzed after Protease M and Protease N treatments, respectively. In gravimetric method, 80.0 and 85.4 mg protein/g RSM were hydrolyzed after Protease M and Protease N treatments. In Kjeldahl method, 67.43 and 70.43 mg protein/g RSM were hydrolyzed after Protamex and Protease N treatments, respectively. For synergistic effect, two or three effective commercial proteases (Protease M, Protease N and Protease A) were applied to RSM at one time. The highest hydrolysis of RSM protein was observed in both Lowry protein assay (80.3 mg protein/g RSM) and gravimetric methods (153.2 mg protein/g RSM) when three commercial proteases were applied at one time, suggesting the synergistic effect of those proteases.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.33 no.4
• /
• pp.317-324
• /
• 2015

GNSS was firstly proposed for application in weather forecasting in the mid-1980s. It has continued to demonstrate the practical uses in GNSS meteorology, and other relevant researches are currently being conducted. Precipitable Water Vapor (PWV), calculated based on the GNSS signal delays due to the troposphere of the Earth, represents the amount of the water vapor in the atmosphere, and it is therefore widely used in the analysis of various weather phenomena such as monitoring of weather conditions and climate change detection. In this study we calculated the PWV through the meteorological information from an Automatic Weather Station (AWS) as well as GNSS data processing of a Continuously Operating Reference Station (CORS) in order to analyze the heavy snowfall of the Ulsan area in early 2014. Song’s model was adopted for the weighted mean temperature model (T_m), which is the most important parameter in the calculation of PWV. The study period is a total of 56 days (February 2013 and 2014). The average PWV of February 2014 was determined to be 11.29 mm, which is 11.34% lower than that of the heavy snowfall period. The average PWV of February 2013 was determined to be 10.34 mm, which is 8.41% lower than that of not the heavy snowfall period. In addition, certain meteorological factors obtained from AWS were compared as well, resulting in a very low correlation of 0.29 with the saturated vapor pressure calculated using the empirical formula of Magnus. The behavioral pattern of PWV has a tendency to change depending on the precipitation type, specifically, snow or rain. It was identified that the PWV showed a sudden increase and a subsequent rapid drop about 6.5 hours before precipitation. It can be concluded that the pattern analysis of GNSS PWV is an effective method to analyze the precursor phenomenon of precipitation.

• Fire Science and Engineering
• /
• v.31 no.5
• /
• pp.53-62
• /
• 2017

Electric power which is the energy source of economy and industries requires long distance transportation due to regional difference between its production and consumption, and it is supplied through the multi-loop transmission and distribution system. Prior to its actual use, electric power flows through several transformations by voltage transformers in substations depending on the characteristics of each usage, and a transformer has the structure consisting of the main body, winding wire, insulating oil and bushings. A transformer fire that breaks out in substations entails the primary damage that interrupts the power supply to houses and commercial facilities and causes various safety accidents as well as the secondary economic losses. It is considered that causes of such fire include the leak of insulating oil resulting from the destruction of bottom part of bushings, and the chain reaction of fire due to insulating oil that reaches its ignition point within 1 second. The smoke detector and automatic fire extinguishing system are established in order to minimize fire damage, but a difficulty in securing golden time for extinguishing fire due to delay in the operation of detector and release of gas from the extinguishing system has become a problem. Accordingly, this study was carried out according to needs of active mechanism to prevent the spread of fire and block the leak of insulating oil, in accordance with the importance of securing golden time in extinguishing a fire in its early stage. A bushings fireproof structure was developed by applying the high temperature shape retention materials, which are expanded by flame, and mechanical flame cutoff devices. The bushings fireproof structure was installed on the transformer model produced by applying the actual standards of bushings and flange, and the full scale fire test was carried out. It was confirmed that the bushings fireproof structure operated at accurate position and height within 3 seconds from the flame initiation. It is considered that it could block the spread of flame effectively in the event of actual transformer fire.

• Restorative Dentistry and Endodontics
• /
• v.34 no.4
• /
• pp.333-339
• /
• 2009

This study was done to determine if there is any difference in microleakage between experimental composite resins, in which various proportions of three component photoinitiators (Camphoroquinone, OPPI, Amine) were included. Four kinds of experimental composite resin were made by mixing 3.2% silanated barium glass (78 wt.%, average size; 1 ${\mu}m$) with each monomer system including variously proportioned photoinitiator systems used for photoinitiating BisGMA/BisEMA/TEGDMA monomer blend (37.5:37.5:25 wt.%). The weight percentage of each component were as follows (in sequence Camphoroquinone, OPPI, Amine): Group A - 0.5%, 0%, 1% / Group B - 2%, 0.2%, 2% / Group C - 0.2%, 1%, 0.2% / Group D - 1%, 1%, 2%. Each composite resin was used as a filling material for round class V cavities (diameter: 2/3 of mesiodistal width; depth: 1.5 mm) made on extracted human premolars and they were polymerized using curing light unit (XL 2500, 3M ESPE) for 40 s with an intensity of 600 mW/$cm^2$. Teeth were thermocycled fivehundred times between $50^{\circ}C$and $550^{\circ}C$for 30s at each temperature. Electrical conductivity (${\mu}A$) was recorded two times (just after thermocycling and after three-month storage in saline solution) by electrochemical method. Microleakage scores of each group according to evaluation time were as follows [Group: at first record / at second record; unit (${\mu}A$)]: A: 3.80 (0.69) / 13.22 (4.48), B: 3.42 (1.33) / 18.84 (5.53), C: 4.18 (2.55) / 28.08 (7.75), D: 4.12 (1.86) / 7.41 (3.41). Just after thermocycling, there was no difference in microleakage between groups, however, group C showed the largest score after three-month storage. Although there seems to be no difference in microleakage between groups just after thermocycling, composite resin with highly concentrated initiation system or classical design (Camphoroquinone and Amine system) would be more desirable for minimizing microleakage after three-month storage.